PK22 AND PKEX22 SERIES - INTENDED FOR DOMESTIC COOKING ONLY READ AND SAVE THESE INSTRUCTIONS
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
INSTALLATION INSTRUCTIONS HB0123 PK22 AND PKEX22 SERIES ! INTENDED FOR DOMESTIC COOKING ONLY ! READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 TO 13. BEST; Hartford, Wisconsin www.BestRangeHoods.com 800-558-1711 BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866-737-7770 To register your product online or for additional information visit www.BestRangeHoods.com SV20827 rev. 03
! WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR 1. For indoor use only. INJURY TO PERSONS, OBSERVE THE FOLLOWING: 2. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone 3. To avoid motor bearing damage and noisy and/or unbalanced number listed in the warranty. impellers, keep drywall spray, construction dust, etc. off power unit. 2. Before servicing or cleaning unit, switch power off at service panel 4. Your power pack motor has a thermal overload which will automatically and lock service disconnecting means to prevent power from being shut off the motor if it becomes overheated. The motor will restart switched on accidentally. When the service disconnecting means when it cools down. If the motor continues to shut off and restart, have cannot be locked, securely fasten a prominent warning device, such the power pack serviced. as a tag, to the service panel. 5. The minimum power pack distance above cooktop must not be less 3. Installation work and electrical wiring must be done by qualified than 24”. A maximum of 30” above cooktop is recommended for best personnel in accordance with all applicable codes and standards, capture of cooking impurities. including fire-rated construction codes and standards. 6. Two installers are recommended because of the large size and weight 4. Sufficient air is needed for proper combustion and exhausting of of this unit. gases through the flue (chimney) of fuel burning equipment to prevent 7. To reduce the risk of fire and to properly exhaust air, be sure to duct air backdrafting. Follow the heating equipment manufacturer’s guidelines outside — Do not exhaust air into spaces within walls or ceiling or into and safety standards such as those published by the National Fire attics, crawl space or garage. Protection Association (NFPA) and the American Society for Heating, 8. This product is equipped with a thermostat which may start blower Refrigeration and Air Conditioning Engineers (ASHRAE) and the local automatically. To reduce the risk of injury and to prevent power from code authorities. being switched on accidentally, switch power off at service panel and 5. When cutting or drilling into wall or ceiling, do not damage electrical lock or tag service panel. wiring and other hidden utilities. 9. Because of the high exhausting capacity of this unit, you should make 6. Ducted fans must always be vented to the outdoors. sure enough air is entering the house to replace exhausted air by 7. Do not use this unit with any solid-state speed control device. opening a window close to or in the kitchen. 8. To reduce the risk of fire, use only metal ductwork. 10. To reduce the risk of fire and electrical shock, the Best models PK22 series should only be installed with their own built-in blowers, and the 9. This unit must be grounded. Best models PKEX22 Series must only be installed with Best external 10. When applicable local regulations comprise more restrictive installation blower models EB6, EB9, EB12 or EB15; or Best in-line blowers and/or certification requirements, the aforementioned requirements models ILB3, ILB6, ILB9, ILB11. Other blowers cannot be substituted. prevail on those of this document and the installer agrees to conform 11. PKEX22 models used with ILB3, ILB6 or EB6 blower, must be installed to these at his own expenses. over ranges rated 60,000 Btu/hr. maximum. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 12. Please read specification label on product for further information and requirements. a) Never leave surface units unattended at high settings. Boilovers cause 13. This power pack is equipped with a RF receiver (optional remote smoking and greasy spillovers that may ignite. Heat oils slowly on low control sold separately). Changes or modifications not expressly or medium settings. approved by the party responsible for compliance could void the b) Always turn power pack ON when cooking at high heat or when user’s authority to operate this product. The remote control has been flambeing food (i.e.: Crêpes Suzette, Cherries Jubilee, Peppercorn tested and found to comply with the limits for a Class B digital device, Beef Flambé). pursuant to part 15 of the FCC Rules and the Canadian ICES-003. These limits are designed to provide reasonable protection against c) Clean ventilating fans frequently. Grease should not be allowed to harmful interference in a residential installation. The remote control accumulate on fan, filters or in exhaust ducts. generates, uses and can radiate radio frequency energy and, if not d) Use proper pan size. Always use cookware appropriate for the size of installed and used in accordance with the instructions, may cause the surface element. harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If TO REDUCE THE RISK OF INJURY TO PERSONS IN THE this equipment does cause harmful interference to radio or television EVENT OF A RANGE TOP GREASE FIRE, OBSERVE reception, which can be determined by turning the equipment off and THE FOLLOWING*: on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, • Reorient or relocate the receiving antenna then turn off the burner. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL • Increase the separation between the equipment and receiver THE FIRE DEPARTMENT. • Connect the equipment into an outlet on a circuit different from that 2. NEVER PICK UP A FLAMING PAN — You may be burned. to which the receiver is connected 3. DO NOT USE WATER, including wet dishcloths or towels — This could cause a violent steam explosion. 4. Use an extinguisher ONLY if: A. You own a Class ABC extinguisher and you know how to operate it. B. The fire is small and contained in the area where it started. C. The fire department has been called. D. You can fight the fire with your back to an exit. * Based on “Kitchen Fire Safety Tips” published by NFPA. 2
- PK22 POWER PACK SYSTEM - MODEL 437 MODEL 441 (HIGH CAPACITY ROOF CAP) (10’’ ROUND WALL CAP) MODEL 418 (10” ROUND ADJUSTABLE ELBOW) MODEL 410 (10” ROUND DUCT — 2 FT. SECTIONS) MODEL 421 (10” ROUND VERTICAL IN-LINE DAMPER SUPPLIED WITH INTERNAL BLOWER POWER PACK) 10” ROUND ADAPTER AL3036, AL3042, AL3948, (SUPPLIED WITH INTERNAL AL3954, AL4554 OR AL4560 BLOWER POWER PACK) CUSTOM HOOD LINER (OPTIONAL) ALP36, ALP42, ALP48, ALP54 OR ALP60 AMBIENT LIGHT PANEL (OPTIONAL) ¤ - + f PK22 POWER PACK ACR1 REMOTE CONTROL (OPTIONAL) HL0192 DUAL BLOWER (1200 CFM) 3
- PKEX22 POWER PACK SYSTEM - MODEL 437 (HIGH CAPACITY ROOF CAP) MODEL ILB9 (800 CFM) OR ILB11 (1100 CFM) IN-LINE BLOWER MODEL EB12 (1200 CFM) (INCLUDES TWO 8” X 12” TO MODEL EB6 (600 CFM) OR EB15 (1500 CFM) OR EB9 (900 CFM) 10’’ ROUND TRANSITIONS) EXTERNAL BLOWER EXTERNAL BLOWER MODEL 441 (10’’ ROUND MODEL 643 WALL CAP) (8” ROUND WALL CAP) MODEL ILB6 (600 CFM) IN-LINE BLOWER (INCLUDES TWO 4½” X 18½” TO 10’’ ROUND TRANSITIONS) MODEL 418 (10” ROUND ADJUSTABLE ELBOW)— OPTIONAL MODEL ILB3 (280 CFM) IN-LINE BLOWER (INCLUDES ONE 8” TO 10” ALP36, ALP42, ALP48, ROUND TRANSITION) MODEL 410 ALP54 OR ALP60 (10” ROUND DUCT AMBIENT LIGHT PANEL (OPTIONAL) — 2 FT. SECTIONS) AL3036, AL3042, AL3948, AL3954, AL4554 OR AL4560 CUSTOM HOOD LINER (OPTIONAL) ¤ - + f ACR1 REMOTE CONTROL PKEX22 POWER PACK (OPTIONAL) HL0193 IN-LINE AND EXTERNAL BLOWER ROUGH-IN KIT (INCLUDED WITH EB6, EB9, EB12, EB15, ILB3, ILB6, ILB9 AND ILB11 BLOWERS.) 4
1. INSTALL DUCTWORK AND ELECTRICAL WIRING For a PKEX22 series power pack, either an external blower or in-line blower must be used. The PKEX22 series power pack must be installed with blower models ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 or EB15 only. Other blowers cannot be substituted (blowers sold separately.) If installing external or in-line blower, refer to instructions packed with blower and follow steps 1 to 6, 11 to 16, 18 and up of this manual. Plan where and how the ductwork will be installed. A straight, short duct run will allow the power pack to perform most efficiently. Long duct runs, elbows and transitions will reduce the performance of the power pack. Use as few of them as possible. Larger ducting may be required for longer duct runs. Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Connect metal ductwork to cap and work back towards the hood location. Use 2” metal foil duct tape to seal the joints. The minimum power pack distance above cooktop must not be less than 24’’. A maximum of 30” above cooktop is recommended for best capture of cooking impurities. Distances over 30” are at the installer and users discretion. ROOF CAP EXTERNAL BLOWER ROOF CAP 10” ROUND DUCT 10” ROUND DUCT (EXCEPT ILB3, 8’’ ROUND DUCT) IN-LINE BLOWER 10” ROUND DUCT 10” ROUND ELBOW 10” VERTICAL DAMPER WALL CAP 10” ROUND ELBOW 10” ROUND ADAPTER WALL CAP EXTERNAL POWER PACK BLOWER POWER PACK POWER PACK 24” TO 30” ABOVE COOKING SURFACE 24” TO 30” 24” TO 30” HH0189A ABOVE COOKING SURFACE HH0190A HH0191A ABOVE COOKING SURFACE PK22 DUAL INTERNAL BLOWER PKEX22 PKEX22 EXTERNAL BLOWER TYPICAL DUCTWORK IN-LINE BLOWER TYPICAL DUCTWORK TYPICAL DUCTWORK (BLOWER LOCATION IS SHOWN NOTE: For external blowers mounted in FOR REFERENCE ONLY) close proximity to power pack, sound level may be higher than specified for internal blowers. 2. PREPARE THE INSTALLATION ! WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. Make sure that the following items are included: - Power pack - Installation instructions - Accessories: • 2 Hybrid baffle filters with handles • Shielded halogen bulbs (120 V, 50 W with GU10 base) (2 for 30” and 39” width power packs, 3 for 45” width power pack) • 10” round adapter and 10” round damper (included with PK22 power pack series only, not with PKEX22 series) • Bag of parts including: 1 wire clamp, 2 wire connectors, 2 no. 8 x 3/8” screws, 6 no. 8-18 x 1¼” chrome plated screws. If applicable, discard extra screws. 5
2. PREPARE THE INSTALLATION (CONT’D) Parts sold separately: - In-line blower assembly model ILB3, ILB6, ILB9 or ILB11. - External blower assembly model EB6, EB9, EB12 or EB15. - Custom hood liner model AL3036, AL3042, AL3948, AL3954, AL4554 or AL4560 (optional). - Ambient light panel model ALP36, ALP42, ALP48, ALP54 or ALP60 (optional). - ACR1 remote control (optional). - Ducts, elbows, wall or roof caps. Refer to pages 3 and 4 for a complete list of venting options and model numbers. - 10” round adapter with rough-in plate kit for PKEX22 series models (included with in-line or external blower kits). NOTE: During installation, protect countertop and/or cooktop. 3. PREPARE CUSTOM HOOD ! WARNING • When building a custom hood, always follow all applicable construction codes and standards. • Make sure the cabinet is capable of supporting its own weight and the weight of the power pack. Failure to do so may cause personal injury or damage to countertop or cooktop. The custom hood must be constructed to fit the size and shape of the power pack. Proper structural support is required to accommodate the weight of the hood. Start with the custom hood base, because its position will determine the height of the PLYWOOD BASE THICKNESS: 3/4” power pack. We recommend the base of the custom hood should be 3/4-inch thick plywood. If an optional custom hood liner will be installed, we recommend the sides 4” FOR LINER and front of the custom hood to be 3/4-inch thick, assuming standard cabinet width . INSTALLATION If the optional custom hood liner will not be installed, the custom hood side and front thickness is at the installer’s discretion. Run power cable to installation location. Stub out a 4-foot length of electrical cable 24” TO 30” ABOVE below the custom hood. COOKING SURFACE POWER PACK WIDTH WITH INTERNAL BLOWER WITH IN-LINE OR EXTERNAL BLOWER 30" 50 LB. - STANDARD 36” H. 39" 54 LB. 36 LB. COOKTOP 45" 57 LB. 39 LB. HH0192A 4. INSTALL CUSTOM HOOD LINER (OPTIONAL) The liners are especially designed to protect the exterior base of the custom hood. Refer to the table below to find the right liner model number for your power pack and custom hood width. To view specifications, including depth for each liner model, visit www.BestRangeHoods.com or contact Technical support (phone number listed on page 13, in warranty text). To install, see instructions packed with custom hood liner. The liner must be installed before the power pack. NOTE: On some liner models, the front liner piece may overlap the power pack front flange. If so, remove the front liner piece, assemble power pack, and reassemble the front liner piece. LINER MODEL POWER PACK MODEL CUSTOM HOOD NOMINAL WIDTH AL3036 PK2230 36" AL3042 PK2230 42" AL3948 PK2239/PKEX2239 48" AL3954 PK2239/PKEX2239 54" AL4554 PK2245/PKEX2245 54" AL4560 PK2245/PKEX2245 60" HA0099A 6
5. CUT HOLE IN CUSTOM HOOD BASE If it is not done yet, cut a hole in the bottom of the cabinet, using the dimensions shown below. POWER PACK WIDTH A 30" 263⁄16" 39" 3415⁄16" 45" 417⁄8" 147⁄8" A HD0496A 6. REMOVE HYBRID BAFFLE FILTERS Remove tape on filters. Remove filters from power pack and set aside. HD0499 7. REMOVE ELECTRICAL COMPARTMENT COVER (PK22 SERIES ONLY) From inside the power pack, remove the wiring cover by removing its retaining screw and set aside. SCREW HD0502 8. INSTALL WIRE CLAMP (PK22 SERIES ONLY) Install the wire clamp (included in parts bag) on top of the power pack. HR0087 7
9. INSTALL 10" ADAPTER (PK22 SERIES ONLY) Using 2 no. 8 x 3/8” screws from parts bag, assemble the adapter on the top of the power pack. MOUNTING SCREW LOCATIONS Seal all joints with metal foil duct tape to eliminate air leaks. HJ0026 10. INSTALL 10" DAMPER (PK22 SERIES ONLY) Install 10” damper (model 421, provided with PK22 series power packs) inside the vertical ductwork that will be attached to the power pack. Do not install in a horizontal ductwork or directly on top of the adapter or it will not open and close properly. Remove shipping tape if present. Secure the 17” MIN. damper to the duct with 3 no. 8 sheet metal screws (not provided). Ensure the damper opens and closes freely. Seal all joints with metal foil duct tape to eliminate air leaks. NOTE: To optimize airflow and reduce noise, position the damper at least 17” above the top of the power pack; or as far as the duct run will allow (see figure at right). HJ0070A 11. INSTALL ROUGH-IN PLATE FOR EXTERNAL BLOWER (PKEX22 SERIES ONLY) Refer to the instructions included with the selected blower/rough-in kit (sold separately) for details on installing the rough-in plate. Install the rough-in WIRING plate so that the wiring box is located on the right side when facing the hood, COVER as specified on the blower housing label. HD0500 LOCK NUTS 8
12. CONNECT WIRING (ALL MODELS) ! WARNING Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Position the power pack below its custom hood. INTERNAL BLOWERS: Insert the house wiring cable through the wire clamp previously installed in step 8. Tighten the wire clamp to secure the cable. Connect cable into electrical compartment using included wire connectors. Connect BLACK to BLACK, WHITE to WHITE and GREEN or bare wire under green ground screw. DO NOT FORGET TO CONNECT THE GROUND. Reinstall electrical compartment cover. IN-LINE OR EXTERNAL BLOWERS: See instructions included with blower. HE0157 13. CONNECT DUCTING (ALL MODELS) A. When there is access to the top of the hood, connect ductwork and seal connections with metal foil duct tape after Step 14 Install power pack. B. When there is no access to the top of the hood, carefully pull down the metal duct through the custom hood base hole. Slide this duct over the adapter (internal blower) or over the flange of the rough-in plate (in-line or external blower). Make sure the adapter/damper assembly enters the ducting. Seal joint with metal foil duct tape. 14. INSTALL POWER PACK CAUTION Take care not to kink ducting when installing the power pack. TIP: Two of the six no. 8-18 x 1¼” provided chrome plated screws can be used to temporarely support the power pack during installation. Place the power pack inside the custom hood and insert both side screws. SUPPORT SCREW LOCATIONS The power pack can now be secured to the custom hood without having to hold it in place. HD0497 Using provided no. 8-18 x 1¼” chrome plated screws, secure the power pack inside the custom hood. Install 1 screw at each corner. (See figure at right for mounting screw locations.) MOUNTING SCREW LOCATIONS HD0498 9
15. INSTALL BLOWER (PKEX22 SERIES ONLY) ! WARNING Do not plug the two cords together. To install, see instructions packed with blower. B A Once the blower is installed, plug the blower cord (A) into the female receptacle and the power supply cord (B) onto the male connector inside the power pack. HE0078 16. REINSTALL HYBRID BAFFLE FILTERS CAUTION Remove protective plastic film covering hybrid baffle filters before installing them. 1 2 1. Insert one end of the hybrid baffle filter into the back channel of the power pack. 2. Raise the other end toward the inside and insert in the front channel of the power pack. Replacement filters are available from your dealer. See label inside power pack for part number. HD0501 17. CALIBRATE IQ BLOWER SYSTEM™ (PK22 SERIES ONLY) After the power pack is installed and wired, engage the calibration process (our Guaranteed Performance System Technology to ensure full-rated airflow is being delivered). Prior to calibration, ensure that all filters, light bulbs and duct system are installed. CALIBRATION PROCESS Hold the calibration button for 3 seconds; calibration button will light up and stay on for up to 13 minutes. The blower will start and begin the calibration process. When calibration is complete, one of two things will occur: A. The blower turns off and calibration button light turns off = Successful calibration. B. The blower turns off and calibration button light blinks continuously = Too much restriction in the ductwork is preventing the IQ Blower System™ from achieving the rated airflow. The blower is automatically set to maximum intensity. CALIBRATION BUTTON NOTE: Common items that cause restrictions: restricted damper flap (backdraft CALIBRATION LIGHT HC0066 damper, wall cap, roof cap), too many elbows, duct size less than 80% of hood outlet, poor transition, use of flex ducting and/or crushed ducting. Two options are available: 1. Press the calibration button to accept airflow as is. The IQ Blower System™ is now configured to its highest possible setting. The blinking calibration light goes out. 2. Correct duct restriction and repeat the calibration process. a. To clear the original calibration data, hold calibration button for 10 seconds. The light will blink 3 times to confirm and the blower configuration will go back to default settings. b. Repeat calibration process. 10
18. LIGHT BULBS This power pack requires shielded halogen lamps (120 V, 50 W, PAR16 with GU10 base, 2 for 30” and 39” width power packs, 3 for 45” width power pack), included. NOTE: Before using lamps, remove shipping tape on them (if present). ! WARNING Do not touch lamps during or soon after operation. Burns may occur. In order to prevent the risk of personal injury, only install shielded halogen lamps. Also, never install a cool beam, a dichroic lamp, a lamp not suitable for use in recessed luminaires or identified for use in enclosed fixtures. 1. Install the lamps by placing the bulb leads into their grooves in the socket. 2. Gently push upwards and turn clockwise until secure. 1 2 To remove lamps, gently push upwards and turn counterclockwise to disengage bulb leads from their grooves. NOTE: If need be, use a rubber dishwashing glove to add grip when removing the bulb; or use suction cup tool available from Best to ease removal of the bulbs. Contact Best Customer Service at 1-800-558-1711 to order suction cup tool, part number 99526707. HO0090 19. USE AND CARE Hybrid Baffle Filters The hybrid baffle filters should be cleaned frequently. Use a warm detergent solution. Wash more often if your cooking style generates greater grease — like frying foods or wok cooking. Remove hybrid baffle filters by pushing them towards the back of power pack and rotating filters downward. Baffle filters are dishwasher safe. Allow filters to dry completely before reinstalling them in the power pack. Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergent or as a result of local water conditions — but this will not affect filter performance. This discoloration is not covered by the warranty. Internal Blowers Cleaning Remove filters in order to access blowers. Vacuum blowers to clean. Do not immerse in water. Power Pack Cleaning Stainless steel cleaning: Do: Don’t: • Regularly wash with clean cloth or rag soaked with warm water • Use any steel or stainless steel wool or any other scrapers to and mild soap or liquid dish detergent. remove stubborn dirt. • Always clean in the direction of original polish lines. • Use any harsh or abrasive cleansers. • Always rinse well with clear water (2 or 3 times) after cleaning. • Allow dirt to accumulate. Wipe dry completely. • Let plaster dust or any other construction residues reach the • You may also use a specialized household stainless steel power pack. During construction/renovation, cover the power cleaner. pack to make sure no dust sticks to stainless steel surface. Avoid when choosing a detergent: - Any cleaners that contain bleach will attack stainless steel. - Any products containing: chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly. - Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are highly explosive and should never be used close to a range. 11
20. OPERATION Always turn your blower on before you begin cooking to establish an airflow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. A) Blower delay-off button SPEED 1 2 3 4 LIGHTING INTENSITY 1 2 3 B) ON blower/Speed control button C) OFF blower/ Filter maintenance button D) OFF lighting E) ON light button (3 settings) HC0016 A B C D E A. BLOWER DELAY-OFF BUTTON: When blower is on, press the delay-off button to activate the delay-off function. The corresponding speed indicator LED will start flashing to indicate this function is activated. The fan will continue to operate for 10 minutes and will stop automatically. To cancel the delay-off function, press the blower delay-off button once again; the blower will then work in normal mode. NOTE: The blower speed can be increased—or decreased—during delay-off mode without starting another 10-minute cycle. B. ON BLOWER/SPEED CONTROL BUTTON: Press this button to turn on the blower at the last selected speed. To change the blower speed, press the button again until the desired speed is obtained. Press and hold this button for 2 seconds to decrease the speed level down by one increment. Possible decreases are then: 4 to 3; 3 to 2; 2 to 1 and 1 to OFF. NOTES: 1. Each time you press the speed control button, the speed changes by increments of 1 (e.g.: speed 1 to speed 2, to speed 3, and then speed 4). From the fourth speed, the speed goes down to level 1. 2. The last speed used is kept in memory so that when the unit is turned on, it will return to the last setting except the fourth, the next time the blower will be turned on, it will return to speed 3. The memorized speed level is also synced with the optional remote control. HEAT SENTRY™ The power pack is equipped with a protective device that activates when excessive heat is detected inside the power pack. This device takes control of the blower and deactivates speed 4 for a 10-minute period and sets it on speed 3. During the Heat Sentry activation, only speed 3 can be used; the speed 4 button will flash while the speed 3 button will light up. ! WARNING The HEAT SENTRY can start the blower during a range top fire or other excessive heat situations even if the power pack is turned off. In this case, it is impossible to turn the blower OFF with blower button. If you must stop the blower on PK22 series models: set the main power switch located behind the baffle filters in OFF position, if it is possible to do safely (see illustration below). For PKEX22 series models: do it from the main electrical panel. PK22 SERIES ONLY MAIN POWER SWITCH HD0517 C. OFF BLOWER/FILTER MAINTENANCE BUTTON: Press this button to turn off the blower. Pressing this button also cancels the delay-off function (if activated). NOTE: After 25 hours of operation, the 4 blower speed lights will flash 30 seconds to indicate the filters need to be cleaned in order to maintain efficient power pack operation. Pressing the OFF button or remote control “f” button will reset the code to indicate that maintenance has been completed. D. OFF LIGHTING: Press this button to turn lights off. E. ON LIGHT BUTTON: Press this button to turn on the halogen lamps. The light intensity changes by increments of 1 (e.g.: Press once for low setting, once again for medium, again for high). From the higher setting, press once to go back to the lower setting. NOTE: The last light setting used is kept in memory. The next time the halogen lamps are turned on, the last setting will be used. The memorized light setting is also synced with the optional remote control. 12
20. OPERATION (CONT’D) OPTIONAL REMOTE CONTROL: ¤ ¤ The power pack can also be operated using the optional ACR1 remote control. When a button is pressed on the remote control, it sends a coded signal to the receiver (factory - + - + installed on the power pack), indicating which function to activate. f ¤ : Activates/deactivates delay-off. f f : Filter maintenance indication timer reset/OFF blower. - : Decreases blower motor speed until turned OFF (4 to 3, 3 to 2, 2 to 1 and 1 to OFF). 1 + : Turns blower motor ON and increases speed (OFF to 1, 1 to 2, 2 to 3, 3 to 4). : Changes light intensity (1-2-3-OFF-1-2-3-OFF). 1 : LED indicator ring (lights up yellow when signal is transmitted to power pack). NOTE: For more information, refer to the instructions included with the remote control. HC0065 The remote control is already configured to operate with the type of RF receiver used in the power pack. However, it is possible to link the remote control to a specific power pack. This procedure may be useful in apartments or condos where many products controlled by a remote control are close to each other. LINKING PROCEDURE (to a specific power pack): 1- Turn lights and blower off. 2- Press and hold the remote control ¤ button for 3 seconds (the LED indicator ring lights up). 3- Press and hold power pack button A for 3 seconds to confirm link. Lighting LED indicators 1 and 3 will then blink 3 times as a completion feedback. Linking procedure needs to be confirmed within 30 seconds, otherwise it will be cancelled. NOTE: Pressing power pack button A for 3 seconds will not enter the linking mode. The linking mode can only be activated from the remote control ¤ button. UNLINKING PROCEDURE: 1- Turn lights and blower off. 2- Press and hold power pack button E for 10 seconds. Lighting LED indicator 2 will then blink 3 times as a completion feedback. 21. WARRANTY ONE-YEAR LIMITED WARRANTY FOR BEST PRODUCTS Broan-NuTone LLC (Broan-NuTone) warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. This warranty does not extend to fluorescent lamp starters, tubes and bulbs, fuses, filters, ducts, roof caps, wall caps and other accessories for ducting. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negligence, accident, improper maintenance or repair (other than by Broan-NuTone), faulty installation or installation contrary to recommended installation instructions. The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states or provinces do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you. BROAN-NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-nutone’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-nutone SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you ma y also have other rights, which vary from state to state or province to another. Any modification performed on this product without the authorization of Broan-NuTone will void this warranty. This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. In USA - Best®, 926 W. State Street, Hartford, WI 53027 (1-800-558-1711) In Canada - Best®, 550 Lemire Blvd., Drummondville, QC, Canada (1-866-737-7770) www.bestrangehoods.com 13
22. WIRING DIAGRAMS Best PK22 series RF RECEIVER POWER E MT_THM1 BLK L K1 K2 K3 K4 WHT N MT_THM2 MOTOR 5 WHT HIGH 4 NEUTRAL BLK RELAY INTERFACE MED HIGH 3 SPEED 1 5 BLU MED LOW 2 SPEED 2 4 5 WHT 3 LOW 1 SPEED 3 4 ORG 2 SPEED 4 3 J1 1 LAMP 3 CALIBRATION BUTTON 2 ~ ~ CALIBRATION - + Q1 - + LOW VAC 2 1 REF ~ ~ 1 J6 J7 YEL RED BLDC1 HALL_1 HALL_2 BLDC2 WHT COLOR CODE BLK 1 2 3 1 2 3 BLK BLACK WHT BLU BLUE RED ORG ORANGE RED RED WHT WHT WHITE T1 WHT YEL YELLOW MAIN SWITCH M M BLK 120 VAC LINE NEUTRAL WHT GROUND BLK BLK HE0156A LAMP LAMP LAMP Best PKEX22 series BLK 1 1 BLK 120 ORG 120 2 2 RF RECEIVER ORG 3 3 BLU 88 WHT 4 4 PPL 60 T3 BLU 5 5 PNK 45 YEL 10 K1 K2 K3 K4 6 6 MOTOR 5 7 7 WHT 0 BLK 8 8 HIGH 4 WHT 9 9 WHT 0 BLK MED HIGH 3 ORG BLK BLK 120 MED LOW 2 1 1 ORG 120 2 2 LOW 1 ORG 3 3 BLU 88 WHT WHT PPL 60 BLK 5 BLU BLU 4 4 PNK 45 T2 J1 5 5 YEL 10 4 LAMP 3 6 6 WHT 0 ~ ~ YEL 7 7 3 Q1 - LOW VAC 2 8 8 - + + RED WHT WHT 0 2 REF 1 9 9 ~ ~ 1 WHT J7 BLK 1 1 BLK 120 ORG 120 2 2 J6 ORG 3 3 BLU 88 WHT PPL 60 BLU 4 4 PNK 45 T1 5 5 YEL 10 6 6 WHT 7 7 WHT 0 8 8 WHT 9 9 WHT 0 FUSE 8 A BLK WHT WHT WHT BLK BLK BLK COLOR CODE LAMP WHT BLK BLACK BLU BLUE BLK BRN BROWN M 120 VAC LINE BLK BLK YEL GRN GREEN LAMP WHT WHT ORG ORANGE NEUTRAL GRN PNK PINK GROUND GRN PPL PURPLE RED RED LAMP WHT WHITE ROUGH-IN PLATE YEL YELLOW HE0155A 14
23. SERVICE PARTS Best PK22 series 1 2 3 16 15 4 5 6 14 REPLACEMENT PARTS AND REPAIRS 13 In order to ensure your unit remains in good working condition, you must use Broan-NuTone genuine replacement 7 parts only. Broan-NuTone genuine replacement parts are specially designed for each unit and are 8 manufactured to comply with all the applicable certification standards and 9 12 maintain a high standard of safety. Any third party replacement part 10 used may cause serious damage and drastically reduce the performance 11 level of your unit, which will result in premature failing. Broan-NuTone recommends to contact a certified service depot for all replacement parts and repairs. HL0199 KEY QTY. (POWER PACK WIDTH) PART NO. DESCRIPTION NO. 30" 39" 45" 1 SV08541 10” ROUND ADAPTER 1 1 1 2 SV08542 10” ROUND DAMPER 1 1 1 3 S97018985 BLDC BLOWER, 600 CFM 2 2 2 4 SV20818 ELECTRONIC DRIVE FOR DUAL BLDC BLOWER 1 1 1 5 SV20817 CALIBRATION BUTTON 1 1 1 6 SV08548 BLACK ROCKER SWITCH 1 1 1 7 SV05917 SOCKET GU10 2 2 3 8 SV09435 SOCKET HOLDER GU10 2 2 3 9 SV09434 LIGHT TRIM STAINLESS STEEL 2 2 3 10 SV05921 HALOGEN BULB 120 V, 50 W, PAR16 WITH GU10 BASE 2 2 3 11 SV61044 FILTER FILLER 0 0 2 SV61045 BAFFLE FILTER WITH MICROMESH + HANDLE 12” X 10” 2 0 0 12 SV61046 BAFFLE FILTER WITH MICROMESH + HANDLE 17” X 10” 0 2 2 13 SV20816 REMOTE CONTROL PCB 1 1 1 14 SV20814 CONTROL INTERFACE PCB FOR INTERNAL BLOWER 1 1 1 15 SV09022 TRANSFORMER 120 VAC, 9 VOLTS DC 1 1 1 16 SV05869 BEST LOGO 1 1 1 * SV20827 INSTALLATION INSTRUCTIONS 1 1 1 PARTS BAG: 1 WIRE CLAMP, 2 WIRE CONNECTORS, 2 NO. 8 X 3/8” SCREWS, * SV20830 1 1 1 6 NO. 8-18 X 1¼” CHROME PLATED SCREWS. * NOT SHOWN. 15
23. SERVICE PARTS (CONT’D) Best PKEX22 series 12 1 11 10 REPLACEMENT PARTS AND REPAIRS 2 In order to ensure your unit remains in good working condition, you must use Broan-NuTone genuine replacement 9 parts only. Broan-NuTone genuine replacement parts are specially designed for each unit and are 3 manufactured to comply with all the applicable certification standards and 4 maintain a high standard of safety. Any third party replacement part 5 8 used may cause serious damage and 6 drastically reduce the performance level of your unit, which will result 7 in premature failing. Broan-NuTone recommends to contact a certified service depot for all replacement parts and repairs. HL0200 KEY QTY. (POWER PACK WIDTH) PART NO. DESCRIPTION NO. 39" 45" 1 SV61049 AUTOTRANSFORMER AND FUSE KIT (INCLUDING METAL SUPPORT) 1 1 2 SV20816 PCB FOR REMOTE CONTROL 1 1 3 SV05917 SOCKET GU10 2 3 4 SV09435 SOCKET HOLDER GU10 2 3 5 SV09434 LIGHT TRIM STAINLESS STEEL 2 3 6 SV05921 HALOGEN BULB 120 V, 50 W, PAR16 WITH GU10 BASE 2 3 7 SV61044 FILTER FILLER 0 2 8 SV61046 BAFFLE FILTER WITH MICROMESH + HANDLE 17” X 10” 2 2 9 SV13924 MALE POWER CONNECTOR 1 1 10 SV13923 FEMALE POWER CONNECTOR 1 1 11 SV20815 CONTROL INTERFACE PCB FOR EXTERNAL BLOWER 1 1 12 SV05869 BEST LOGO 1 1 * SV20827 INSTALLATION INSTRUCTIONS 1 1 PARTS BAG: 1 WIRE CLAMP, 2 WIRE CONNECTORS, 2 NO. 8 X 3/8” SCREWS, * SV20830 1 1 6 NO. 8-18 X 1¼” CHROME PLATED SCREWS. * NOT SHOWN. 16
GUIDE D’INSTALLATION HB0123 SÉRIES PK22 ET PKEX22 ! CONÇUES POUR USAGE DOMESTIQUE SEULEMENT ! LIRE ET CONSERVER CES DIRECTIVES INSTALLATEUR : LAISSER CE GUIDE AU PROPRIÉTAIRE. PROPRIÉTAIRE : DIRECTIVES D’UTILISATION ET D’ENTRETIEN EN PAGES 27 À 29. BEST; Hartford, Wisconsin www.BestRangeHoods.com 800 558-1711 BEST; Drummondville, QC, Canada www.BestRangeHoods.com 866 737-7770 Pour enregistrer votre produit en ligne ou pour obtenir plus d’information, consultez notre site www.BestRangeHoods.com SV20827 rév. 03
! AVERTISSEMENT ATTENTION AFIN DE RÉDUIRE LES RISQUES D’INCENDIE, 1. Pour une utilisation à l’intérieur seulement. D’ÉLECTROCUTION OU DE BLESSURES CORPORELLES, 2. Pour usage domestique seulement. Ne pas utiliser pour évacuer des SUIVEZ LES DIRECTIVES SUIVANTES : vapeurs ou des matières dangereuses ou explosives. 1. N’utilisez cet appareil que de la façon prévue par le manufacturier. Si 3. Afin d’éviter tout dommage au moteur et de débalancer ou de vous avez des questions, contactez le manufacturier à l’adresse ou au rendre bruyante la roue du moteur, garder votre appareil à l’abri des numéro de téléphone indiqués dans la garantie. poussières de gypse et de construction/rénovation, etc. 2. Avant de réparer ou de nettoyer l’appareil, couper l’alimentation 4. Le moteur de votre hotte encastrable possède une protection électrique en verrouillant le panneau de distribution afin d’éviter sa thermique qui éteindra automatiquement le moteur s’il devient remise en marche accidentelle. Si le panneau de distribution ne peut surchauffé. Le moteur redémarrera automatiquement une fois refroidi. être verrouillé, y fixer un avertissement en évidence, telle qu’une Si le moteur continue à arrêter et à redémarrer, faites-le vérifier. étiquette de couleur vive. 5. La distance minimale entre le bas de votre hotte et la surface de 3. Les travaux d’installation et de raccordement électrique doivent être cuisson ne doit pas être inférieure à 24 po. Un maximum de 30 po effectués par une personne qualifiée, conformément aux codes et au-dessus de la surface de cuisson est recommandé pour une aux standards de construction, incluant ceux concernant la protection meilleure évacuation des odeurs de cuisson. contre les incendies. 6. Deux installateurs sont recommandés lors de l’installation vu la grande 4. Une quantité d’air adéquate est requise afin d’assurer une bonne dimension et le poids de cet appareil. combustion et l’évacuation des gaz par la cheminée dans le cas des équipements alimentés au gaz afin de prévenir les retours de 7. Afin de réduire les risques d’incendie, assurez-vous d’évacuer l’air à cheminée. Conformez-vous aux instructions et aux standards de l’extérieur. Ne pas évacuer l’air dans des espaces restreints comme sécurité des manufacturiers d’équipement de chauffage, tel qu’ils l’intérieur des murs ou plafond ou dans le grenier, faux plafond sont publiés par la National Fire Protection Association (NFPA) et ou garage. l’American Society for Heating, Refrigeration and Air Conditioning 8. Cet appareil est équipé d’un thermostat pouvant faire démarrer le Engineers (ASHRAE) ainsi que les responsables des codes locaux. ventilateur automatiquement. Afin de réduire le risque de blessure, 5. Lorsque vous coupez ou perforez un mur ou un plafond, prenez garde couper le courant à partir du panneau électrique et le verrouiller ou de ne pas endommager les fils électriques ou autre installation qui apposer un avertissement sur le panneau afin de prévenir que la hotte pourraient y être dissimulés. ne soit mise en marche accidentellement. 6. Les ventilateurs avec conduits doivent toujours évacuer l’air 9. À cause de la grande capacité d’évacuation de cet appareil, il est à l’extérieur. recommandé d’ouvrir une fenêtre dans ou près de la cuisine afin de 7. Ne pas utiliser cet appareil avec une commande de vitesse à remplacer l’air évacué. semi-conducteur. 10. Afin de réduire les risques d’incendie et d’électrocution, les modèles 8. Afin de réduire les risques d’incendie, n’utilisez que des conduits Best de la série PK22 doivent être installés uniquement avec leurs de métal. ventilateurs internes intégrés et les modèles Best de la série PKEX22 9. Cet appareil doit être mis à la terre. avec les ventilateurs externes EB6, EB9, EB12 ou EB15 ou un 10. Lorsqu’une réglementation est en vigueur et qu’elle comporte des ventilateur en ligne ILB3, ILB6, ILB9, ILB11. Aucun autre ventilateur ne exigences d’installation et/ou de certification plus restrictives, lesdites doit être utilisé. exigences prévalent sur celles de ce document et l’installateur entend 11. Les modèles PKEX22 utilisés avec les ventilateurs ILB3, ILB6 ou s’y conformer à ses frais. EB6, doivent être installés au-dessus d’une cuisinière produisant un maximum de 60 000 Btu/h. AFIN DE RÉDUIRE LES RISQUES DE FEU DE CUISINIÈRE : 12. Veuillez consulter l’autocollant apposé à l’intérieur du produit pour a) Ne jamais laisser les appareils de cuisson sans surveillance lorsqu’ils plus d’information ou autres exigences. sont réglés à feu vif. Les débordements engendrent de la fumée et 13. Cette hotte encastrable est munie d’un récepteur radio (télécommande des déversements graisseux pouvant s’enflammer. Chauffez l’huile optionnelle vendue séparément). Tous changements ou modifications lentement, à feu doux ou moyen. qui ne sont pas approuvés par la partie responsable de la b) Mettez toujours la hotte en marche lorsque vous cuisinez à feu vif ou conformité pourraient annuler la possibilité d’opérer l’équipement. que vous cuisinez des mets flambés (par ex. : crêpes Suzette, cerises La télécommande a été testée et est en accord avec les limites de jubilé, steaks au poivre flambés). la Classe B appareil numérique et est conforme au chapitre 15 des c) Nettoyez régulièrement la (les) roue(s) du ventilateur. Ne laissez pas règlements FCC et ICES-003 canadien. Ces limites sont développées la graisse s’accumuler sur le ventilateur, les filtres ou les conduits afin de fournir une protection raisonnable contre des interférences d’évacuation. dommagables dans une installation résidentielle. La télécommande d) Utilisez le bon format de casserole. Servez-vous toujours de casseroles génère, utilise et peut émettre des flux de fréquences radio qui et d’ustensiles appropriés à la dimension de la surface chauffante. peuvent causer des interférences aux communications radio, si elle n’est pas installée selon les instructions. Cependant, il n’y a aucune AFIN D’ÉVITER TOUT RISQUE DE BLESSURES LORS D’UN garantie que ces dites interférences ne se produiront pas dans une FEU DE CUISINIÈRE, SUIVEZ CES DIRECTIVES* : installation particulière. Si cet équipement cause des interférences 1. Étouffez les flammes avec un couvercle hermétique, une tôle à biscuits à un récepteur radio ou un téléviseur, cela peut être confirmé en ou un plateau métallique et ensuite, éteindre le brûleur. PRENEZ éteignant et rallumant l’appareil, l’usager est encouragé à corriger SOIN D’ÉVITER les brûlures. SI LES FLAMMES NE S’ÉTEIGNENT cette situation en essayant les solutions suivantes : PAS IMMÉDIATEMENT, ÉVACUEZ LES LIEUX ET APPELEZ • Réorienter ou relocaliser l’antenne réceptrice LES POMPIERS. • Augmenter la distance entre l’équipement et le récepteur 2. NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMMES DANS VOS MAINS. Vous pourriez vous brûler. • Connecter l’équipement à une autre prise électrique ou un autre disjoncteur différent de celui du récepteur 3. N’UTILISEZ PAS D’EAU, incluant un linge à vaisselle ou une serviette mouillée, cela pourrait occasionner une violente explosion de vapeur. 4. N’utilisez un extincteur QUE DANS LE CAS OÙ : A. Vous savez qu’il s’agit d’un extincteur de classe ABC et que vous en connaissez le fonctionnement. B. L’incendie est petit et limité à l’endroit où il a débuté. C. Les pompiers ont été avisés. D. Vous pouvez combattre l’incendie en ayant accès à une sortie de secours. *Tirées du Kitchen Fire Safety Tips publié par la NFPA. 18
- SYSTÈME DE HOTTE ENCASTRABLE - SÉRIE PK22 MODÈLE 437 MODÈLE 441 (CAPUCHON DE TOIT (CAPUCHON MURAL À HAUT RENDEMENT) 10 PO ROND) MODÈLE 418 (COUDE AJUSTABLE DE 10 PO ROND) MODÈLE 410 (CONDUIT DE 10 PO ROND — SECTIONS DE 2 PI) MODÈLE 421 (VOLET VERTICAL EN LIGNE DE 10 PO ROND FOURNI AVEC LA HOTTE ENCASTRABLE À VENTILATEUR INTERNE) REVÊTEMENT D’ARMOIRE (OPTIONNEL) ADAPTATEUR DE 10 PO ROND AL3036, AL3042, AL3948, (FOURNI AVEC LA HOTTE ENCASTRABLE À VENTILATEUR INTERNE) AL3954, AL4554 OU AL4560 PANNEAU D’ÉCLAIRAGE (OPTIONNEL) ALP36, ALP42, ALP48, ALP54 OU ALP60 ¤ - + f HOTTE ENCASTRABLE PK22 TÉLÉCOMMANDE ACR1 (OPTIONNELLE) HL0192 VENTILATEUR INTERNE (1200 PCM) 19
- SYSTÈME DE HOTTE ENCASTRABLE - SÉRIE PKEX22 MODÈLE 437 (CAPUCHON DE TOIT À HAUT RENDEMENT) VENTILATEUR EN LIGNE MODÈLE ILB9 (800 PCM) OU ILB11 (1100 PCM) (INCLUANT DEUX VENTILATEUR EXTERNE VENTILATEUR EXTERNE TRANSITIONS RONDES DE MODÈLE EB6 (600 PCM) MODÈLE EB12 (1200 PCM) 8 PO X 12 PO À 10 PO) OU EB15 (1500 PCM) OU EB9 (900 PCM) MODÈLE 441 MODÈLE 643 (CAPUCHON MURAL (CAPUCHON 10 PO ROND) MURAL 8 PO ROND) VENTILATEUR EN LIGNE MODÈLE ILB6 (600 PCM) (INCLUANT DEUX TRANSITIONS RONDES DE 4½ PO X 18½ PO À 10 PO) MODÈLE 418 (COUDE AJUSTABLE DE 10 PO ROND) — OPTIONNEL VENTILATEUR EN LIGNE 10 PO MODÈLE ILB3 (280 PCM) (INCLUANT UNE TRANSITION MODÈLE 410 PANNEAU D’ÉCLAIRAGE (OPTIONNEL) RONDE DE 8 PO À 10 PO) (CONDUIT DE 10 PO ROND ALP36, ALP42, ALP48, — SECTIONS DE 2 PI) ALP54 OU ALP60 REVÊTEMENT D’ARMOIRE (OPTIONNEL) AL3036, AL3042, AL3948, AL3954, AL4554 OU AL4560 ¤ - + f TÉLÉCOMMANDE ACR1 HOTTE ENCASTRABLE PKEX22 (OPTIONNELLE) HL0193 PLAQUE VENTILATEUR POUR VENTILATEURS EXTERNES OU EN LIGNE (INCLUSE AVEC LES VENTILATEURS EB6, EB9, EB12, EB15, ILB3, ILB6, ILB9 ET ILB11). 20
1. INSTALLER LES CONDUITS ET LE CÂBLAGE ÉLECTRIQUE Les hottes encastrables de série PKEX22 doivent être munies d’un ventilateur externe ou en ligne. Elles doivent être installées avec un ventilateur de modèle ILB3, ILB6, ILB9, ILB11, EB6, EB9, EB12 ou EB15 seulement. Aucun autre ventilateur ne peut être utilisé (ventilateurs vendus séparément). Si un ventilateur externe ou en ligne est installé, se reporter aux directives incluses avec celui-ci et suivre les étapes 1 à 6, 11 à 16, 18 et suivantes de ce guide. Déterminer à quel endroit et de quelle façon les conduits seront installés. Un conduit droit et court permettra à la hotte encastrable de fonctionner plus efficacement. Un conduit long avec des coudes et des transitions réduira la performance de la hotte. En utiliser le moins possible. Pour une grande distance, un conduit d’évacuation d’air au diamètre plus grand peut être requis. Installer des conduits de dimensions appropriées, coude(s) et capuchon de mur ou de toit selon le type de ventilateur. Relier le conduit de métal au capuchon, puis acheminer le conduit jusqu’à l’emplacement de la hotte. Sceller les joints avec du ruban adhésif de métal de 2 po de largeur. La distance minimale entre le bas de la hotte et la surface de cuisson ne doit pas être inférieure à 24 po. Un maximum de 30 po au-dessus de la surface de cuisson est fortement recommandé pour une meilleure évacuation des odeurs de cuisson. Une distance de plus de 30 po demeure à la discrétion de l’installateur et de l’utilisateur. CAPUCHON VENTILATEUR EXTERNE CAPUCHON DE TOIT DE TOIT CONDUIT ROND CONDUIT ROND DE 10 PO DE 10 PO (SAUF ILB3, CONDUIT ROND DE 8 PO) CONDUIT ROND VENTILATEUR EN LIGNE DE 10 PO COUDE ROND DE 10 PO VOLET VERTICAL CAPUCHON COUDE ROND DE 10 PO ROND DE 10 PO DE MUR ADAPTATEUR CAPUCHON DE 10 PO ROND VENTILATEUR DE MUR EXTERNE HOTTE HOTTE HOTTE ENCASTRABLE ENCASTRABLE ENCASTRABLE DE 24 PO À 30 PO DE 24 PO À 30 PO AU-DESSUS AU-DESSUS DE LA SURFACE DE LA SURFACE DE CUISSON DE 24 PO À 30 PO HH0189F AU-DESSUS DE LA SURFACE DE CUISSON HH0190F HH0191F DE CUISSON INSTALLATION TYPE PK22 INSTALLATION TYPE INSTALLATION TYPE VENTILATEUR INTERNE DOUBLE VENTILATEUR EN LIGNE PKEX22 VENTILATEUR EXTERNE PKEX22 (L’EMPLACEMENT DU VENTILATEUR NOTE : Le niveau sonore peut être plus EST ILLUSTRÉ À TITRE élevé que spécifié lorsqu’un DE RÉFÉRENCE SEULEMENT) ventilateur externe est installé à proximité de la hotte encastrable. 2. PRÉPARER L’INSTALLATION ! AVERTISSEMENT Il est recommandé de porter des lunettes et des gants de sécurité lors de l’installation, de l’entretien et de la réparation de cet appareil. NOTE : Avant de commencer l’installation, vérifier le contenu de la boîte. Si des pièces sont manquantes ou endommagées, contacter le manufacturier. S’assurer que les articles suivants soient inclus : - La hotte encastrable - Le guide d’installation - Accessoires : • 2 filtres à chicane hybrides avec poignées • Ampoules halogènes avec écran (120 V, 50 W à culot GU10) (2 pour les modèles de 30 po et 39 po de largeur, 3 pour le modèle de 45 po de largeur) • Adaptateur de 10 po rond et volet de 10 po rond (inclus avec le modèle PK22 seulement, et non avec le modèle PKEX22) • Sac de pièces incluant : 1 serre-fils, 2 capuchons de connexion, 2 vis n° 8 x 3/8 po, 6 vis n° 8-18 x 1¼ po plaquées chrome. Jeter les vis excédentaires s’il y a lieu. 21
2. PRÉPARER L’INSTALLATION (SUITE) Pièces vendues séparément : - Ventilateur en ligne modèle ILB3, ILB6, ILB9 ou ILB11. - Ventilateur externe modèle EB6, EB9, EB12 ou EB15. - Revêtement d’armoire, modèle AL3036, AL3042, AL3948, AL3954, AL4554 ou AL4560 (optionnel). - Panneau d’éclairage d’ambiance modèle ALP36, ALP42, ALP48, ALP54 ou ALP60 (optionnel). - Télécommande ACR1 (optionnelle). - Conduits, coudes, capuchons de mur ou de toit. Consulter les pages 19 et 20 pour la liste complète des accessoires de ventilation et les numéros de modèle. - Adaptateur de 10 po rond avec plaque ventilateur pour les modèles de la série PKEX22 (inclus avec les ensembles ventilateur en ligne ou externes). NOTE : Lors de l’installation, protéger le plan de cuisson et le comptoir de cuisine. 3. PRÉPARER L’ARMOIRE POUR HOTTE ! AVERTISSEMENT • Toujours suivre les codes et standards en vigueur lors de la contruction de l’armoire pour hotte. • S’assurer que l’armoire puisse supporter son propre poids en plus de celui de la hotte encastrable. Ne pas suivre cette directive peut entraîner des blessures corporelles ou des dommages à la surface de cuisson ou au comptoir de cuisine. Construire l’armoire en fonction du format et du poids total de la hotte encastrable. Une structure de soutien appropriée est nécessaire afin de supporter adéquatement le poids de la hotte. ÉPAISSEUR DE LA BASE DE CONTREPLAQUÉ : 3/4 PO Commencer par la base de l’armoire, car sa position déterminera la hauteur de la hotte encastrable. Nous recommandons qu’elle soit faite de contreplaqué de 4 PO POUR L’INSTAL. DU 3/4 po d’épaisseur. Si un revêtement d’armoire optionnel sera installé, nous REVÊTEMENT D’ARMOIRE recommandons que les côtés et l’avant de l’armoire aient aussi 3/4 po d’épaisseur, selon que l’armoire soit de largeur standard. Si le revêtement d’armoire optionnel 24 PO À 30 PO n’est pas installé, l’épaisseur des côtés et de l’avant de l’armoire est à la discrétion AU-DESSUS de l’installateur. DE LA SURFACE DE CUISSON Passer l’alimentation électrique jusqu’à l’endroit de l’installation. Laisser dépasser une longueur de 4 pi de câble électrique sous l’armoire. LARGEUR DE LA AVEC VENTILATEUR AVEC VENTILATEUR HOTTE ENCASTRABLE INTERNE EN LIGNE OU EXT. SURFACE DE CUISSON STANDARD 30 PO 50 LB - DE 36 PO DE HAUTEUR 39 PO 54 LB 36 LB 45 PO 57 LB 39 LB HH0192F 4. INSTALLER LE REVÊTEMENT D’ARMOIRE (OPTIONNEL) Les revêtements d’armoire sont spécialement conçus pour protéger la base de l’armoire. Consulter le tableau ci-dessous afin de trouver le modèle de revêtement correspondant à votre hotte ainsi qu’à la largeur de l’armoire. Visiter le site www.BestRangeHoods.com ou communiquer avec le service technique (le numéro de téléphone se trouve dans le texte de garantie, en page 29) afin de connaître leurs caractéristiques, incluant la profondeur de chacun des modèles. Pour l’installation, voir la feuille d’instruction du revêtement d’armoire. Le revêtement d’armoire doit être installé avant la hotte encastrable. NOTE : Il est possible que la pièce avant de certains modèles de revêtement d’armoire empiète sur le rebord avant de la hotte encastrable. Si tel est le cas, retirer cette pièce, assembler la hotte encastrable et réinstaller la pièce avant du revêtement d’armoire. REVÊTEMENT HOTTE ENCASTRABLE LARGEUR NOMINALE DE L’ARMOIRE AL3036 PK2230 36 PO AL3042 PK2230 42 PO AL3948 PK2239/PKEX2239 48 PO AL3954 PK2239/PKEX2239 54 PO AL4554 PK2245/PKEX2245 54 PO AL4560 PK2245/PKEX2245 60 PO HA0099F 22
5. DÉCOUPER LE TROU DANS LA BASE DE L’ARMOIRE Si ce n’est pas déjà fait, découper le trou dans la base de l’armoire selon les dimensions indiquées ci-dessous. LARGEUR DE LA A HOTTE ENCASTRABLE 30 PO 263⁄16 PO 39 PO 3415⁄16 PO 147⁄8 PO 45 PO 417⁄8 PO A HD0496F 6. RETIRER LES FILTRES À CHICANE HYBRIDES Retirer le ruban adhésif des filtres. Retirer les filtres de la hotte encastrable et les mettre de côté. HD0499 7. RETIRER LE COUVERCLE DU COMPARTIMENT ÉLECTRIQUE (SÉRIE PK22 SEULEMENT) Par l’intérieur de la hotte encastrable, enlever le couvercle du compartiment électrique en retirant sa vis de retenue et le mettre de côté. VIS HD0502 8. INSTALLER LE SERRE-FILS (SÉRIE PK22 SEULEMENT) Installer le serre-fils (inclus dans le sac de pièces) sur le dessus de la hotte encastrable. HR0087 23
You can also read