MCPC TP/BNC OPERATION MANUAL
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
McPC TP/BNC Operation Manual
FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
The use of non-shielded I/O cables may not guarantee compliance with FCC RFI limits. This digital apparatus does not exceed the Class B
limits for radio noise emission from digital apparatus set out in the Radio Interference Regulation of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B
prescrites dans le Règlement sur le brouillage radioélectrique publié par le ministère des Communications du Canada.
Warranty
IMC Networks warrants to the original end-user purchaser that this product, EXCLUSIVE OF SOFTWARE, shall be free
from defects in materials and workmanship under normal and proper use in accordance with IMC Networks' instructions
and directions for a period of six (6) years after the original date of purchase. This warranty is subject to the limitations set
forth below.
At its option, IMC Networks will repair or replace at no charge the product which proves to be defective within such
warranty period. This limited warranty shall not apply if the IMC Networks product has been damaged by unreasonable
use, accident, negligence, service or modification by anyone other than an authorized IMC Networks Service Technician
or by any other causes unrelated to defective materials or workmanship. Any replaced or repaired products or parts carry
a ninety (90) day warranty or the remainder of the initial warranty period, whichever is longer.
To receive in-warranty service, the defective product must be received at IMC Networks no later than the end of the
warranty period. The product must be accompanied by proof of purchase, satisfactory to IMC Networks, denoting
product serial number and purchase date, a written description of the defect and a Return Merchandise Authorization
(RMA) number issued by IMC Networks. No products will be accepted by IMC Networks which do not have an RMA
number. For an RMA number, contact IMC Networks at PHONE: (800) 624-1070 (in the U.S and Canada) or (949) 465-
3000 or FAX: (949) 465-3020. The end-user shall return the defective product to IMC Networks, freight, customs and
handling charges prepaid. End-user agrees to accept all liability for loss of or damages to the returned product during
shipment. IMC Networks shall repair or replace the returned product, at its option, and return the repaired or new
product to the end-user, freight prepaid, via method to be determined by IMC Networks. IMC Networks shall not be
liable for any costs of procurement of substitute goods, loss of profits, or any incidental, consequential, and/or special
damages of any kind resulting from a breach of any applicable express or implied warranty, breach of any obligation
arising from breach of warranty, or otherwise with respect to the manufacture and sale of any IMC Networks product,
whether or not IMC Networks has been advised of the possibility of such loss or damage.
EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, IMC NETWORKS MAKES NO OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WITH RESPECT TO THIS IMC NETWORKS PRODUCT, INCLUDING WITHOUT
LIMITATION ANY SOFTWARE ASSOCIATED OR INCLUDED. IMC NETWORKS SHALL DISREGARD AND NOT BE
BOUND BY ANY REPRESENTATIONS OR WARRANTIES MADE BY ANY OTHER PERSON, INCLUDING EMPLOYEES,
DISTRIBUTORS, RESELLERS OR DEALERS OF IMC NETWORKS, WHICH ARE
INCONSISTENT WITH THE WARRANTY SET FORTH ABOVE. ALL IMPLIED WARRANTIES INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED TO THE DURATION OF THE
EXPRESS WARRANTY STATED ABOVE.
Every reasonable effort has been made to ensure that IMC Networks product manuals and promotional materials
accurately describe IMC Networks product specifications and capabilities at the time of publication. However, because of
ongoing improvements and updating of IMC Networks products, IMC Networks cannot guarantee the accuracy of printed
materials after the date of publication and disclaims liability for changes, errors or omissions.
ii
Table of Contents
FCC Radio Frequency Interference Statement ....................................................ii
Warranty............................................................................................................ii
About the McPC TP/BNC ...................................................................................4
Installation Instructions.......................................................................................4
Configuration .....................................................................................................5
Twisted Pair Crossover/Straight-Through Switch..................................................5
BNC Port Termination........................................................................................5
LED Indicators....................................................................................................6
IMC Networks Technical Support.......................................................................6
Specifications .....................................................................................................6
Safety Certifications............................................................................................7
iiiAbout the McPC TP/BNC
The McPC™ TP/BNC is a low-cost, preconfigured, IEEE 802.3 single-conversion PC
media converter that converts between 10Base-T twisted pair and 10Base-2 thin
coax. It is available with one RJ45 connector for the twisted pair port and one BNC
connector for the coax port.
The McPC TP/BNC can be mounted in any PC with a standard PCI slot. It includes
diagnostic LEDs for each port and a 4-pin peripheral power supply connector.
Installation Instructions
To install a McPC, perform the
following steps:
1. Turn off the power on your PC.
2. Remove the cover.
3. Find an empty slot.
4. Align the McPC in the slot.
5. Mount the McPC by screwing its
bracket to the computer casing,
making sure the McPC does not
extend past the edge of your
case.
6. Attach the keyed mini-power
connector to the McPC.
7. Attach the male end of the “Y” connector to a standard size power connector in
your computer.
8. Replace the cover.
9. Attach the cables between the McPC and the devices that will be interconnected.
Note
McPCs DO NOT plug into the motherboard. The McPC only needs power from the
computer; no additional power source is necessary.
4Configuration
The following diagram shows the faceplate for the McPC TP/BNC:
McPC TP/BNC, Front View
After installation, you can configure McPCs for the following features, depending on
the requirements of your installation:
• Crossover/straight-through connection on the twisted pair port
• BNC Port Termination.
Twisted Pair Crossover/Straight-Through Switch
The twisted pair port features a push-button switch, located next to the RJ45
connector, for selecting a crossover workstation connection or straight-through
repeater/hub connection for this port.
To select a straight-through connection, simply press the push-button IN. A crossover
connection is selected when the push-button is OUT.
If uncertain whether a crossover or straight-through connection is needed, set the
push-button to the position that makes the LNK (link) LED glow.
BNC Port Termination
The McPC TP/BNC features a 2-position switch next to the BNC connector that
allows a thin coaxial segment to be terminated at the port without an additional ‘T’
connector and terminator.
If the McPC TP/BNC is attached to a mid-point of
a thin Ethernet segment, attach a ‘T’ connector to
the BNC port. Termination must be OFF
(disabled). Termination is disabled when the
switch is in the left position.
If a thin Ethernet segment is to be terminated at
the McPC TP/BNC, attach the cable directly to the
BNC connector and set the termination switch to ON (enabled – factory default) by
moving the switch to the right position.
5LED Indicators
The McPC TP/BNC features four diagnostic LEDs.
These LEDs include the following:
• TP LNK - Blinks yellow when twisted pair port is receiving data.
• BNC ACT - Glows green when a BNC port is receiving data.
• BNC COL - Blinks red in normal operation indicating normal collisions are being
detected on the BNC segment.
• POWER - Glows yellow when the McPC is receiving power.
IMC Networks Technical Support
Phone: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada);
+32-16-550880 (Europe)
Fax: (949) 465-3020
E-Mail: techsupport@imcnetworks.com
Web: www.imcnetworks.com
Specifications
Operating Temperature*:
32° to 104°F (0° to +40°C); 5% to 90% (non-condensing), 0 to 10,000 ft. altitude
Storage Temperature*:
22° to +160°F (-6° to +71°C); 5 to 95% (non-condensing)
Electrical
Input Load: 5 VDC ±5%, 0.7 A max
Dimensions
A single PCI slot module for use in a PC chassis.
6Safety Certifications
UL/CUL: Listed to Safety of Information Technology Equipment, including
Electrical Business Equipment.
CE: The products described herein comply with the Council Directive on
Electromagnetic Compatibility (89/336/EEC) and the Council Directive
on Electrical Equipment Designed for use within Certain Voltage Limits
(73/23/EEC). Certified to Safety of Information Technology Equipment,
Including Electrical Business Equipment. For further details, contact
IMC Networks.
Class 1 Laser product, Luokan 1 Laserlaite,
Laser Klasse 1, Appareil A’Laser de Classe 1
European Directive 2002/96/EC (WEEE) requires that any equipment that bears this
symbol on product or packaging must not be disposed of with unsorted municipal
waste. This symbol indicates that the equipment should be disposed of separately
from regular household waste. It is the consumer’s responsibility to dispose of this
and all equipment so marked through designated collection facilities appointed by
government or local authorities. Following these steps through proper disposal and
recycling will help prevent potential negative consequences to the environment and
human health. For more detailed information about proper disposal, please contact
local authorities, waste disposal services, or the point of purchase for this equipment.
719772 Pauling • Foothill Ranch, CA 92610-2611 USA
TEL: (949) 465-3000 • FAX: (949) 465-3020
www.imcnetworks.com
© 2007 IMC Networks. All rights reserved.
The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any
errors that may appear in this document. McPC TP/BNC is a trademark of IMC Networks. Other brands or product
names may be trademarks and are the property of their respective companies.
Document Number 55-80246-00 A3 July 2007
If the product’s part number begins with an “8”, it is compliant with the Restriction of Hazardous Substances (RoHS)
directive.You can also read
