Ford Mustang Adjustable Rear Wing Part #R03030120
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Ford Mustang Adjustable Rear Wing
Part #R03030120
Installation Instructions
Application: 2005 - 2008 Ford Mustang
Before installing your Roush Performance Product(s), read through the entire installation procedure and
check to make sure all items are present.
1305-R03030121-AA Page 1 of 10 1-800-59-ROUSH
Packaging List for Rear Wing Kit
Description RPP Part Number Qty
Rear Wing Kit R03030120 1
Carbon Fiber Airfoil 1
Carbon Fiber Side Plates 2
Black Aluminum Upper Pedestal - LH 1
Black Aluminum Upper Pedestal - RH 1
Black Aluminum Lower Pedestal 2
Adjustable Rods 2
Rubber Upper Pedestal Gasket 2
Carbon Fiber Base Plate 2
Rubber Base Plate Gasket 2
M8 Nylok Nuts 6
M8 x 20mm Button Head Bolts 10
M6 Studs 8
M6 x 25mm Button Head Bolts 4
M6 Washers 8
M6 Nylok Nuts 8
3mm Hex Key 1
4mm Hex Key 1
5mm Hex Key 1
Installation Instructions R03030121 1
1305-R03030121-AA Page 2 of 10 1-800-59-ROUSH
Equipment and Supplies Required
• Metric socket set
• Metric wrench set
• E6 Inverted Torx socket
• A solvent to aid in glue removal (acetone)
• 5/16” drill bit
LIMIT OF LIABILITY STATEMENT
The information contained in this publication was accurate and in effect at the time the publication
was approved for printing and is subject to change without notice or liability.
Roush Performance Products (RPP) reserves the right to revise the information presented herein or
to discontinue the production of parts described at any time.
1. SAFETY REQUIREMENTS
STOP! READ IMPORTANT SAFETY CAUTIONS AND WARNINGS BEFORE PROCEEDING.
IMPORTANT SAFETY NOTICE
Appropriate disassembly, assembly methods and procedures are essential to ensure the personal
safety of the individual performing the kit installation. Improper installation due to the failure to
correctly follow these instructions could cause personal injury or death. Read each step of the
installation manual carefully before starting the actual installation.
1. Always wear safety glasses for eye protection.
2. Place ignition switch in the OFF position.
3. Always apply the parking brake when working on a vehicle.
4. Block the front and rear tire surface to prevent unexpected vehicle movement.
5. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide.
6. Do not smoke or use flammable items near or around the fuel system.
7. Use chemicals and cleaners in well-ventilated areas.
8. Batteries produce explosive gases, which can cause personal injury. Therefore, do not allow
flames, sparks or flammable substances to come near the battery.
9. Keeps hands and any other objects away from the radiator fan blades.
10. Keep yourself and your clothing away from moving parts when the engine is running.
11. Do not wear loose clothing or jewelry that can get caught in rotating parts or scratch surface
finishes.
1305-R03030121-AA Page 3 of 10 1-800-59-ROUSH
Factory Wing Removal
1) From the inside of the deck lid, remove the four (4) wing retaining nuts and save for reuse. The
wing is also held on with double sided tape and will not fall free yet.
2) Remove the four (4) studs using an inverted Torx socket and save for reuse.
3) Protect the top of the quarter panel under each end of the factory wing with blankets or towels to
prevent damage from contact with the wing as it is removed.
4) Break the wing (tape) free of the deck lid. Clean off any remaining tape residue from the deck lid.
Deck Lid Modification
1) Place one of the carbon fiber mounting bases on the deck lid aligning the second and third holes in
the base with the factory holes in the deck lid.
1305-R03030121-AA Page 4 of 10 1-800-59-ROUSH
2) Measure the distance from the edge of the base to the nearest edge of the deck lid at the front and
rear of the base. Adjust the location of the base so that the measurement is equal at the front and
rear aligned with the factory holes. Mark the location of the forward hole for drilling. Repeat for
the opposite side.
Mark this hole
Equal distance from edge
Align this hole
3) Drill 5/16” holes where marked.
4) Protect the bare metal in the holes you drilled with touch-up paint or similar to prevent corrosion.
1305-R03030121-AA Page 5 of 10 1-800-59-ROUSH
Assembly of the Roush Wing
Note: When installed, the ends of the wing will sweep forward. The concave edge of the wing is referred
to as forward and the convex edge as rear.
1) Place a blanket or towels over a table to prevent damage to the wing. Place the wing on the table,
bottom side up (threaded inserts facing up).
2) Place a rubber upper pedestal gasket over one pair of the mounting inserts with the short end of the
gasket facing forward.
1305-R03030121-AA Page 6 of 10 1-800-59-ROUSH
3) Position one of the Black Aluminum Upper Pedestals over the gaskets with the long leg of the
pedestal towards the rear of the wing and the slotted side of the bolt recess facing the center of the
wing. Hand start two(2) M6 bolts. Carefully position the gasket to be centered under the pedestal
and tighten using the supplied 4mm hex key to 5 Nm (44 lb-in).
Long leg towards Slotted recess towards
rear of wing center of wing
4) Install a supplied M6 stud into the first hole in the one of the Black Aluminum Lower Pedestals and
snug using the supplied 3mm wrench. Install two (2) of the take-off wing studs into the 2nd and 3rd
holes and snug using an E6 Torx socket.
Forward
5th 4th 3rd 2nd 1st
Note: Included in the kit are enough studs, nuts and washers to use on the lower base instead of reusing
the factory takeout studs and nuts if you prefer to keep all the fasteners the same.
1305-R03030121-AA Page 7 of 10 1-800-59-ROUSH
5) Install the lower pedestal to the upper pedestal using a supplied M8 bolt and M8 Nylock Nut.
Tighten the bolt only until slightly snug. The nut will lock it in place, allowing the lower pedestal to
swivel in the assembly.
6) Install the Adjustable Rod using two (2) more M8 bolts and 8mm Nylok Nuts. Again, tighten the
bolt only until slightly snug to allow the brackets to move when adjusted. Adjust the length of the
rods for desired downforce. The recommended Roush setting is 118mm across the centers of the
adjuster mounting bolts.
7) Repeat the procedure for other pedestal.
1305-R03030121-AA Page 8 of 10 1-800-59-ROUSH
Installation of Roush Wing
1) Unlatch the deck lid lock but leave the deck lid closed.
2) Place a Base Plate Gasket over the holes on each end of the deck lid with the thick end of the
gasket towards the rear of the vehicle.
3) Align the Base Plate over the holes on the gasket.
4) Carefully drop the assembled wing into the holes. It may be necessary to push the pedestals inward
or outward to align the studs with the holes.
5) While holding the wing in place and with a factory take off “wing” nut in hand, lift the deck lid
slightly and reach in and start a nut on one stud on each side of the deck lid.
6) With the wing secured with at least 2 hand started nuts, open the deck lid and install the remaining
two (2) take off nuts onto the factory take off studs, and M6 Washers and M6 Nylock Nuts over the
supplied studs. .
7) Recheck wing, base plate, and gasket alignment and then tighten all six base nuts to 5 Nm (44 lb-
in).
1305-R03030121-AA Page 9 of 10 1-800-59-ROUSH
8) Install the side plates with the supplied M8 bolts. Tighten end plate bolts to 8Nm (70 lb-in).
Top Edge
Front Edge
Note: If items are missing or for any questions regarding the installation of this kit, please
contact Roush Performance toll free at 1-800-59-ROUSH.
WARRANTY
All retail parts carry a 90-day warranty from the date of purchase. This warranty covers defects in materials
or workmanship, and does not include (i) normal wear and tear, environmental conditions, improper
installation; (ii) road hazards, misuse, abuse, neglect, accidents, collision, fire, theft, freezing, vandalism,
riot, explosion, or objects striking the vehicle; (iii) misusing the vehicle, such as driving over curbs,
overloading, racing, or using the vehicle as a stationary power source; (iv) altering, disassembling or
modifying the parts; (v) defects caused or induced by failures, breakdowns, or damage by other parts,
components or the vehicle; (vi) subjecting the parts to excessive moisture or water or any motor vehicle
fluids (e.g.: oil, anti-freeze, battery acid, brake fluid, etc.); (vii) acts of God, natural disasters and other
similar causes beyond the reasonable control of Roush; or (viii) application of chemicals that affect the
parts. This Limited Warranty does not cover surface deterioration of paint, trim, and appearance items that
result from use and/or exposure to the elements, such as stone chips, scratches, bird droppings, lightning,
hail, windstorm, dings, dents, earthquake, road salt, tree sap, water or flood.
ROUSH SHALL NOT BE LIABLE TO REIMBURSE CUSTOMER/DEALER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE INSTALLATION OR USE OF ANY PRODUCT SOLD
THROUGH THIS CATALOG OR ARISING OUT OF ANY BREACH OF WARRANTY, EXCEPT AS MAY BE STATED
IN THIS CATALOG, ROUSH DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
ROUSH’S LIABILITY EXCEED THE PRICE PAID BY CUSTOMER/DEALER FOR PRODUCTS SOLD REGARDLESS
IF ROUSH HAS BEEN ADVISED IN ADVANCE OF ANY POTENTIAL PROBLEM OR IF A CLAIM IS BASED ON
CONTRACT, TORT, STRICT LIABILITY, PRODUCT LIABILITY OR OTHERWISE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR THEIR DURATION, OR LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY
NOT APPLY.
1305-R03030121-AA Page 10 of 10 1-800-59-ROUSHYou can also read
