Fire damper EKO-SRB1 - Installation, operating and maintenance instructions 2021-03 - EKOVENT AB
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Fire damper EKO-SRB1
Installation, operating and maintenance instructions 2021-03Installation, operating and maintenance instructions EKO-SRB1
Table of Contents
Product handling.........................................3
General assembly........................................4
Mounting accessories.................................5
Installation instructions............................ 5-6
Operation and maintenance........................7
Declaration Of Performance........................8
2
Owner of place of manufacture: EKOVENT AB, Vellinge
Certification: 0402 SP Certification
Product type description: EKO-SRB1
Aproval number: SC0848-13
Fire classification: E 60 (ve i< >o, ho i< >o) SC20 000
EKOVENT AB We reserve the right to make changes 2021-03Product handling on the construction site
Transport Storage
The fire dampers are transported to the The storage of materials on the site should
construction site with a forklift or crane be planned so that you get the least pos-
with a lifting fork. To avoid damage, they sible internal transport. The fire dampers
must be lifted, not dragged and never lo- must be protected against water and
wered hard against the ground. always stored in a dry place. Furthermore,
they must be handled so that no mechani-
Reception and inspection cal damage occurs to them.
of the delivery
The fire dampers are inspected imme- Commissioning
diately when the delivery arrives at the The fire dampers must not be put into use
workplace. The inspection is to check that until the entire installation is in operational
the delivery corresponds to the order and condition.
the consignment note. The approved deli-
very is acknowledged on the consignment
note. Products with defects or defects
must not be installed. Contact the supplier
immediately. 3
EKOVENT AB hereby disclaims all responsibility for:
– Damage due to incorrect transport, EKOVENT:s liability shall be limited to repair
handling or storage. or replacement of faulty equipment part.
– That the user has failed to inspect,
maintain and to a reasonable extent
take care of the equipment.
– Personal injury or property damage as
a result of using the product in violation
of the instructions and specifications in
this manual.
EKOVENT AB We reserve the right to make changes 2021-03Installation, operating and maintenance instructions EKO-SRB1
General assembly
Why Fire dampers?
Fire dampers are one of several factors
in a building that together must provide
good fire protection in the event of a fire.
The fire protection requirements are mainly
affected by building class, fire load, heat
output, air supply, the rescue service’s
response time and the presence of fire
protection technical installations. An al-
ternative to calculations or to prove that
selected solutions meet the set functional
requirements is to use P- and CE-marked
products.
Mounting Electrical connection
In order for the P- and CE marking to To be performed by a qualified electrician
apply, assembly must always take place according to drawings and current wiring
4 in accordance with the supplied assembly diagram.
instructions. Other details such as flexible
wall sleeve and wall to damper caulking are
ordered separately. The hole size is always
the damper diameter + 55 mm.
Wiring diagram actuator
EKOVENT AB We reserve the right to make changes 2021-03Mounting accessories EKO-SRB1
Flexible wall sleeve EKO-GIS
Installation
90
5
Mounting instructions EKO-SRB1
Installation in flexible wall
sleeve EKO-GIS
Gipsväggstos EKO-GIS_mellanvägg 2013
Plåtskruv eller
popnit av stål
1. Squeeze the wall sleeve EKO-GIS and
insert it into the hole.
2. Lock the wall sleeve with a sheet metal
screw or pop rivets in the overlap.
EKO SRBG Gipsväggsstos Mont 2013
EKOVENT AB We reserve the right to make changes 2021-03Installation, operating and maintenance instructions EKO-SRB1
Assembly instruction EKO-SRB1
Supporting construction - wall or floor in fire resistance class EI 60.
P-approval SC0848-13
Suspension
Duct
EKO-
Ø A+55
SRB1
Duct Duct
EKO- SRB1
Fire sealant *
Duct
6
Fire sealant *
Important! The smoke damper should always be installed with the blade
EKO-SRB1 Mont schakt 2014
shaft horizontal..
1. The duct system should be suspen- – The damper blade shaft must always
ded and insulated in accordance with be installed horizontally.
the fire resistance of the supporting
3. Mount the thermal sensor with the sen-
construction in which the hole is made
sor probe in the air flow, ensuring that it
(EI 60). Insulation of the ventilation
does not obstruct the movement of the
duct must be done in accordance with
damper blade.
“Installationsbrandskydd Ventilation
– Rör” section 21.3.4 (ISBN: 978-91- 4. The following minimum dimensions
633-1723-1) corresponding to the fire must be observed when mounting
resistance of the supporting construc- – Minimum distance between dampers:
tion in which the hole is made (EI 60). 200 mm.
– Minimum distance to supporting con-
2. Mount the damper in the duct.
struction: 75 mm.
– No gaps between the damper and
the supporting construction.
* Fire sealing must be done using an
approved method that complies with
the relevant fire classification, e.g.
EKO-KER, EKO-GIS and fire protection
sealant.
EKOVENT AB We reserve the right to make changes 2021-03Operation and maintenance
Operation check which is located on the front of
Fire damper EKO-SRB1 is a P- and CE the monitoring unit (applies to EKO-KE).
marked damper for fire separation of hea- Powerless damper closes. Check that
ting, ventilation and air conditioning instal- the damper is fully open during opera-
lations in buildings. EKO-SRB1 is always tion, closes and opens completely during
supplied with an electric safety actuator testing and closes completely in the event
complete with thermal sensor that discon- of a power failure. Otherwise follow the
nects the power to the actuator if the tem- instructions for monitoring systems EKO –
perature exceeds 72 °C. The facility must MKE/SKE, EKO-KE, EKO-TME/TSE, MME/
have a smoke detector which indicates an SME.
alarm and which closes the fire damper
and which must be connected to moni- Cleaning
toring systems EKO-MKE/SKE, EKO-KE, We advocate preventive maintenance of
EKO-TME/TSE, MME/SME or equivalent. the damper according to the facilities
Automatic function check takes place eve- needs. Clean the damper blade and dam-
ry 48 hours (or at more frequent intervals), per (inside) with a brush, vacuuming or
malfunction is shown in the display. wiping. NOTE! Water or other liquids must
not be used. Regular testing according to
Maintenance 7
the P-approval.
External and internal control
At least every three years, check the elec-
Note!
trical wiring for actuators, end position
After inspection, the fire damper must
contacts and smoke detectors as well as
be left in normal working position.
the damper cover so that no foreign de-
tails can prevent the damper blade from
Warning!
moving. Also check the attachment of
Never keep your hands inside the dam-
the actuator, damper blade and sealing
per when it closes. Risk of crushing
strip so that no damage has occurred.
injuries.
Also check that the corrosion protection
is intact.
Spare parts list
Function control Actuator, see type designation of the ac-
Automatic: see above. tuator.
Manuell: Manual: Manual function check
can be performed from the central unit
menu. During installation, manual function
check can also be performed on the re-
spective slave unit (applies to EKO-MKE/
SKE, EKO-TME/TSE, MME/SME). Manual
function check can be done by pressing
the test button for automatic function
EKOVENT AB We reserve the right to make changes 2021-03Installation, operating and maintenance instructions EKO-SRB1
Declaration Of Performance
DECLARATION OF PERFORMAN
CE
Fire Damper SRB1
Type and batch number accord
ing to product label.
Fire damper to be used in conjun
ction with fire separating eleme
compartmentation of at least 60 nts to maintain fire
min according to EN 15650.2010
EKOVENT AB, Mejselgatan 7, 23532
Vellinge, www.ekovent.se
Certificate:
SP Technical Research Institute
of Sweden, nr 0402, has perfor
the manufacturing plant and factor med type testing, initial inspection
y production control (FPC) under of
system 1
EC Certificate of Conformity 0402-
CPR-SC0844-13
Size
Type
Ø 100 mm till Ø 630 mm Classification
8 Horizontal duct
E 60 (ho i o) S
Vertical duct
E 60 (Ve i o) S
Classification according to EN 13501
-3
Nominal activation conditions/s
ensitivity: Pass
- Sensing element load bearing ISO 10294-4
capacity
- Sensing element response tempe
rature
Response delay (reponse time):
Pass EN 1366-2
-Closure time
Operational reliability:
Pass EN 1366-2
-Cycling
Durability of response delay:
Pass EN 1366-2
- Sensing element responset o
temperature and load bearing capac
ity
Durability of operational reliability:
20 000 cycles -Pass EN 15650:2010
-Open and closing cycle tests
The performance of SRB1 is in confo
rmity with the declared performance
above.
This declaration of performance
is issued under the sole responsibili
ty of EKOVENT AB.
Signed for and on behalf of the
manufacturer by:
______________________________
_________
Vellinge 2017-09-20, Michael Bränd
ström R&D Manager
EKOVENT AB, Mejselgatan 7
SE-235 32 Vellinge Sweden, +46
40 42 16 00
EKOVENT AB We reserve the right to make changes 2021-03Notes:
9
EKOVENT AB We reserve the right to make changes 2021-03REGIONAL OFFICE GÖTEBORG
Boråsvägen 5, 435 31 Mölnlycke
HEAD OFFICE Tel 031-23 07 40
Mejselgatan 7, 235 32 Vellinge
Tel 040-42 16 00 REGIONAL OFFICE STOCKHOLM
Vallgatan 9, 170 67 Solna
www.ekovent.se info@ekovent.se Tel 08-508 613 00You can also read
