Standard: Numbering and Titling Specification - Standard Number: HPC-9CA-01-0002-2012 - Horizon Power
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Standard: Numbering and Titling Specification Standard Number: HPC-9CA-01-0002-2012
Document Control
Revision 17 Author Name: Claire Hand
Claire Digitally signed by
Claire Hand
Position: Engineering Drawing System
Specialist
Hand Date: 2020.06.01
19:28:33 +08'00'
Reviewed By Name: Robert Golding
Digitally signed by
Robert Golding
Position: Drawings and CAD Systems Date: 2020.06.02
22:15:53 +08'00'
Specialist
Endorsed By Name: Sandeep Magan Digitally signed by
Sandeep Magan
Date: 2020.06.03
Position: Engineering Services Manager 09:21:02 +08'00'
Approved By Name: Marc Beckx Digitally signed
by Marc Beckx
Position: Manager Engineering and Project Date: 2020.06.04
Services 15:26:06 +08'00'
Date Created/Last Updated 26 May 2020
Review Frequency* 3 years
Next Review Date 26 May 2023
* Frequency period is dependent upon circumstances– maximum is 5 years from last issue, review, or revision
whichever is the latest. If left blank, the default must be 1 year unless otherwise specified.
Revision Control
Revision Date Description
17 26/05/2020 Numbering and Titling Documents updated and combined.
HPC-9CA-01-0003-2012 Drawing Titles and HPC-9CA-01-0004-2013 Standard
Drawing Numbers superseded by incorporating into this standard.
Refer to Appendix A for Full Revision History.
STAKEHOLDERS
The following positions must be consulted if an update or review is required:
EPCM Contracts Manager Senior Engineer Secondary Systems
Engineering Services Manager Major Project Directors
Asset Managers
DM# 9118921 HPC-9CA-01-0002-2012 Page 2 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.TABLE OF CONTENTS
1 PURPOSE .................................................................................................... 5
2 COMPLIANCE .............................................................................................. 5
3 OWNERSHIP ................................................................................................ 5
4 REFERENCES ............................................................................................. 5
5 DEFINITIONS AND ABBREVIATIONS ........................................................ 5
6 GENERAL REQUIREMENTS ...................................................................... 7
6.1 Request for Numbers ............................................................................................... 7
7 DOCUMENT NUMBER STRUCTURE AND CODING ................................. 8
7.1 Legacy Drawings ...................................................................................................... 8
Current drawing number vs legacy ( Including Western Power) ............................................ 8
South Hedland and Hedland Projects..................................................................................... 8
7.2 Structure ................................................................................................................... 8
Location Drawing Number Convention ................................................................................... 8
Transmission Line Drawing Number Convention ................................................................... 8
Concept and Tender Drawing Number Convention................................................................ 9
Standalone Power Systems Numbering Convention............................................................ 10
Document Numbering Convention........................................................................................ 11
8 REDLINE NUMBERING ............................................................................. 12
9 REVISION NUMBERING ............................................................................ 13
9.1 Revision Description............................................................................................... 14
9.2 Cancelled deliverables ........................................................................................... 14
9.3 Superseded deliverables ........................................................................................ 14
9.4 File name ............................................................................................................... 14
File names for legacy drawings ............................................................................................ 14
10 STANDARDS DOCUMENTS AND NUMBERS ......................................... 15
10.1 Standard drawings numbering ............................................................................... 15
10.2 Distribution Standards Drawings ............................................................................ 16
10.3 Distribution Standards Drawings Versioning .......................................................... 17
10.4 Standards Document Numbering ........................................................................... 17
11 DRAWING TITLING ................................................................................... 19
11.1 Titles ....................................................................................................................... 19
DM# 9118921 HPC-9CA-01-0002-2012 Page 3 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX A - REVISION INFORMATION ............................................................. 20
APPENDIX B - LOCATION CODES (NUMBERING & TITLING) ............................ 21
APPENDIX C - FACILITY CODES (NUMBERING) ................................................. 28
APPENDIX D - DISCIPLINE CODES (NUMBERING) ............................................. 29
APPENDIX E - DOCUMENT AND DRAWING TYPES (NUMBERING & TITLING) 31
APPENDIX F - DRAWING TITLE REFERENCES ................................................... 42
APPENDIX G - TRANSMISSION LINE PREFIX ..................................................... 46
APPENDIX H - LEGACY NUMBERING .................................................................. 48
APPENDIX I - WESTERN POWER LEGACY DRAWING NUMBERING STANDARD
........................................................................................................ 52
DM# 9118921 HPC-9CA-01-0002-2012 Page 4 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.1 PURPOSE
This Specification defines the requirements for Numbering and Titling of Engineering Technical
Documents and Drawings for Horizon Power.
This Specification also captures legacy numbering that was used as a convention prior to Horizon
Power (previously Western Power and State Energy Commission of WA - SECWA) which is still used
in current projects.
2 COMPLIANCE
All personnel involved in the creation and/or revision of Engineering Technical Documents and
Drawings will comply with this specification. This includes project participants, Contractors, Suppliers
and Principal Representatives.
3 OWNERSHIP
Documents created by, or on behalf of Horizon Power are an asset of value.
Engineering Technical Document and Drawings are and shall remain the property of Horizon Power
and are not for distribution outside of Horizon Power except where specifically authorised by Horizon
Power.
4 REFERENCES
Document Number Description
HPC-9CA-01-0001-2012
Engineering Drawings, General Requirements, Practices and
Preparation of Drawings / CAD Specification
5 DEFINITIONS AND ABBREVIATIONS
Term Description
Attribute A unique part of a document number.
Contractor The provider of goods or services under the Contract
Commercial
Commercially related documents applicable to a contract and/or project
Documentation
Formal communication between two or more parties for example a letter or
Correspondence
memo.
This code is used to define the broad content of the document differentiating
Discipline code
between for instance Mechanical and Quality.
This code further defines the document into specific kind of documents being
either discipline specific or used by many disciplines; for instance, a single line
Document Type
diagram is a unique document type associated to the Electrical discipline while
document type plan is generic.
DM# 9118921 HPC-9CA-01-0002-2012 Page 5 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.Term Description
Documents are all documents created for the purposes of the Contract and/or
Document project that contain specific information about the facility and/or equipment and
include the electronic files of such documents.
Drawing The Principal’s Drawing Management Group provides document management
Management and control services. Including systematic registration, dissemination, control,
Group status reporting and storage of Controlled Documents.
Drawings are all drawings, plans, sketches and layouts created for the
Drawings purposes of the Contract and/or project and include electronic files of such
documents.
Ellipse Enterprise Management System.
Facility Primary area within the location that the drawing is most appropriate.
Horizon Power Regional Power Corporation.
Location Location of the Site that the drawing or document refers to.
Outdated or obsolete numbering no longer in use / numbering may be used for
Legacy
existing sites and facilities for revisions. May not be used for new Sites and
numbering
drawings.
A single project identifier assigned by for inclusion in all document numbers
Project Identifier
generated by Horizon Power or its Contractors.
Originator
A code to identify the organization responsible for the development of the
(Correspondence
document.
Only)
Principal Horizon Power (Regional Power Corporation)
Principal
Document A number allocated to a document by The Principal.
Number
Project
Management Documents that communicate non-technical information regarding the project.
Documentation
Project A single project identifier assigned by Horizon Power for inclusion in all
Identifier/Contract documentation numbers generated for the project; combined with the contract
Number number to define a specific Supplier package identifier.
The Horizon Power application used for storing and managing all Controlled
ProjectWise
Engineering Technical Documents, Drawings and relative Engineering Data.
An Alpha, Numeric or Numeric Alpha code to track and define the version of a
Revision
document at a particular point in the lifecycle.
Recipient
(Correspondence/ A code to identify the receiving organization.
Commercial Only)
DM# 9118921 HPC-9CA-01-0002-2012 Page 6 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.Term Description
Horizon Power Standard is a document or drawing that prescribes the
Standard
mandatory requirements for all Engineering work performed.
A person or company that assumes by secondary contract some or all of the
Subcontractor
obligations of an original contractor.
Sub Supplier A Supplier who provides goods or services to another Supplier.
Supplier Providers of equipment.
Formal information which includes text documents, databases, and drawings
Technical
that communicate technical information pertaining to the physical or functional
Documentation
requirements of a project.
WBS Work Break Down Structure.
Work The Supplier/Contractor Scope of Work and Services defined in the Contract.
6 GENERAL REQUIREMENTS
All document authors will and are responsible for ensuring an appropriate document number is
requested as per the instructions outlined in section 6.1 Request for Number; prior to development of a
document.
The Principal’s Document Control Group shall allocate all document and drawing numbers.
Registrations are recorded in the Horizon Power’s Technical Document Management System (DMS)
ProjectWise.
Supplier/Contractor will assign a Principal Document Number to all documents which are generated as
part of the execution of Work; including those produced by any Subcontractors or Sub suppliers.
6.1 Request for Numbers
All requests for numbers shall be sent to Horizon Power Document Control.
Email address: HPDC@horizonpower.com.au
All requests for numbers shall be on the latest revision of the electronic form, HPA-0000000-DC-FRM-
0001.
This is obtainable from Horizon Power Drawing Management Group.
DM# 9118921 HPC-9CA-01-0002-2012 Page 7 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.7 DOCUMENT NUMBER STRUCTURE AND CODING
7.1 Legacy Drawings
Current drawing number vs legacy ( Including Western Power)
Legacy drawing numbering convention shall only to be used in the scenario of an existing drawing (built
during the legacy drawing numbering phase) undertaking an upgrade to the already constructed
infrastructure. The legacy drawing numbering convention must not be used in the design/
commissioning phases of any new facilities. Horizon Power Drawing Management Group will allocate
all legacy drawing numbers. Refer to Appendix H.2
South Hedland and Hedland Projects
South Hedland and Hedland projects used a different numbering format as shown in Appendix H.1.
Moving forward the new numbering drawing convention will be used.
7.2 Structure
Location Drawing Number Convention
Principal’s Representative will use the following numbering convention.
Table 7-2-1 Location Drawing Number Convention
AAA - AA - AA - AAA - NNNN - NN
Location Doc. Sequence Sheet
- Facility - Discipline - - -
Code Type Number Number
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example HDT-SS-EL-LAY-0001-01
1. Location Code – Location of the Site, refer to Appendix B
2. Facility Code - For a list of Facility codes, refer to Appendix C
3. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document.
Refer to Appendix D
4. Document Type – For a list of document types, refer to Appendix E
5. Sequence – Document Control will assign a four-digit sequential number to all
documents, so each resulting number is unique.
6. Sheet Number - Document Control will assign a two-digit sequential number
Transmission Line Drawing Number Convention
The Transmission Line drawing identifier shall include the substations at both ends of the line, with the
following rules governing the order of precedence:-
DM# 9118921 HPC-9CA-01-0002-2012 Page 8 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.1) Power stations (energy sources) shall have the highest order of precedence
2) Terminal Yards shall be the next in the order of precedence
3) This will be followed by Zone substations, as the lowest order of precedence
4) If the line connects two locations of equal precedence, then the location with the higher
alphabetical order will take precedence.
Examples:
SHP - SHT 31 (SHP takes precedence as it is a Power Station and SHT is a Terminal Yard)
KRT - BUL 81 (KRT takes precedence as it is a Terminal Yard and BUL is a Zone Substation)
HDT - SHT X1 (both locations are Terminals, i.e. equal precedence. HDT takes precedence
as it is higher on the alphabetical order)
Principal’s Representative will use the following numbering convention.
Table 7-2-2 Transmission Line Drawing Number Convention
AAAAAAAA - AA - AA - AAA - NNNN - NN
Transmission Doc. Sequence Sheet
- Facility - Discipline - - -
Line Code Type Number Number
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example: KRTDMP81-TL-EL-RPL-0001-01
1. Transmission Line Code – Transmission Line codes, refer to Appendix G
2. Facility Code - For a list of Facility codes, refer to Appendix C
3. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document.
Refer to Appendix D
4. Document Type – For a list of document types, refer to Appendix E
5. Sequence – Document Control will assign a four-digit sequential number to all documents,
so each resulting number is unique.
6. Sheet Number - Document Control will assign a two-digit sequential number
Concept and Tender Drawing Number Convention
To differentiate current drawings from Tender / Concept drawings, Project specific drawing numbers
shall be allocated.
This allows the current drawing to remain available for active projects. The new project drawing will
copy the content from the live drawing. The current drawing shall be referenced in the title block of the
new project drawing.
Once the project is confirmed by the HP Project Manager, the current drawing will be checked out for
Modification and the concept drawing shall be superseded. The current drawing will incorporate the
changes from the concept as required.
DM# 9118921 HPC-9CA-01-0002-2012 Page 9 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.Principal’s Representative will use the following numbering convention.
Table 7-2-3 Concept / Tender Drawing Number Convention
AAAAAAAA - AA - AA - AAA - NNNN - NN
Project Doc. Sequence Sheet
- Facility - Discipline - - -
Number Type Number Number
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example: M0001557-TL-EL-LAY-0001-01
1. Project Number – The Job number applicable to the project defined by Ellipse
2. Facility Code - For a list of Facility codes, refer to Appendix C
3. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document.
Refer to Appendix D
4. Document Type – For a list of document types, refer to Appendix E
5. Sequence – Document Control will assign a four-digit sequential number to all documents,
so each resulting number is unique.
6. Sheet Number - Document Control will assign a two-digit sequential number
Standalone Power Systems Numbering Convention
Principal’s Representative will use the following numbering convention.
Table 7-2-4 Standalone Power Systems Drawing Number Convention
AAA ‐ AA ‐ AA ‐ AAA ‐ NNNN ‐ NN
Ellipse
Asset or
Doc. Sequence
Location Code - Standard - Discipline - - - Sheet Number
Type Number
Project
Identifier
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example:
EHR-GS011-EL-DGA-0005-05 – Site Asset Specific Drawing Number
EHR-GP2095-EL-DGA-0005-05 - Project Standard Specific Drawing Number
(Across Multiple Sites)
1. Location Code – Location of the Site, refer to Appendix B
2. Generation Systems / Generation Project Identifier
DM# 9118921 HPC-9CA-01-0002-2012 Page 10 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.Individual Site Assets will be allocated a unique identifier generated from Ellipse.
(GS011)
Project Standard Specific drawings that will be used across all sites will be allocated a
Generation Project Identifier. Last four digits of the project number shall be used
(GP2095)
3. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document.
Refer to Appendix D
4. Document Type – For a list of document types, refer to Appendix E
5. Sequence – Document Control will assign a four-digit sequential number to all
documents, so each resulting number is unique.
6. Sheet Number - Document Control will assign a two-digit sequential number
Document Numbering Convention
Principal’s Representative will use the following numbering convention.
Table 7-2-5 Document Numbering Convention
AAAAAAAA - AAAAAAA - AAA - AA - AAA - NNNN
Contract
Number /
PO
Project NUMBER Location Sequence
- - - Discipline - Doc. Type -
Number (If Code Number
Applicable
)
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example:
M0001557-0000000-DMP-EL-RPT-0001 - Non Contractual
M0001557-HP12345-DMP-EL-RPT-0001 Horizon Power Contractual Document
M0001557-S123456-DMP-EL-RPT-0001 – Non Specific HP Contractual Documents (
EPCM)
1. Project Number – The Job number applicable to the project defined by Ellipse
2. Contract Number / Purchase Order Number – Unique Contract / Purchase Order
Specific Identifier will be allocated by the Project. Please use the General Code
(0000000) if a Contract number / PO Number is not applicable. Horizon Power specific
Contracts shall use HPXXXXX for ease of Identification. Non Specific HP Contracts
(Supplier ie.EPCM / Subcontractor contract number) shall use SXXXXXX and will be
assigned to all supplier data documentation denoted by the prefix S
3. Location Code – Location of the Site, refer to Appendix B
DM# 9118921 HPC-9CA-01-0002-2012 Page 11 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.4. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document.
Refer to Appendix D
5. Document Type – For a list of document types, refer to Appendix E
6. Sequence – Document Control will assign a four-digit sequential number to all
documents, so each resulting number is unique.
8 REDLINE NUMBERING
A redline drawing could be a hand or electronic mark-up drawing, showing the ‘as built\as constructed’
status of the drawing. The redline drawings are used to provide as constructed and up to date
information to those who require it to proceed with Work; whilst the drawing is being back-drafted to an
‘as built’ status, if applicable.
Redline drawings are not a formal revision and as such are to be numbered using the numbering
conventions described within this document suffixed by one the following extensions.
_REV RLMU – Redline Mark Up.
_REV RLNC – Redline No Change.
For Example: HDT-SS-EL-LAY-0001-01_0 RLMU
Where there are multiple redline mark-ups on the same drawing number and revision then the suffix is
to include a numeric identifier. For example; _RLMU1, RLMU2 etc.
DM# 9118921 HPC-9CA-01-0002-2012 Page 12 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.9 REVISION NUMBERING
All revisions of a document must be issued to Horizon Power Drawing Management Group in sequential
order. Documents that skip revisions will be returned to the originator for correction.
Principal shall consider all documents having an alpha revision to be in the review or approval cycle or
to have an issue status of issued for review, issued for tender or information only.
Controlled deliverables will be allocated a Revision as shown in the matrices below.
Table 9-1 Revision Number for New Documents and Drawings
Table 9-2 Revision Sequence for the Update of Existing Documents and Drawings
DM# 9118921 HPC-9CA-01-0002-2012 Page 13 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.9.1 Revision Description
The revision description describes the status of the document within the lifecycle of the document at a
specific point in time.
The revision description is different to the issue reason; which describes why a specific document is
being transmitted.
The Project Number shall be added to the IFC and As Built Revision Descriptions, e.g. “Issued for
Construction for PN123456” “AS BUILT for PN123456”
9.2 Cancelled deliverables
Where a deliverable is cancelled, the drawings shall be revised to the next revision, watermarked
‘CANCELLED’ and the revision description updated to reflect the reason for cancellation.
Drawings are then delivered to Document Control to be uploaded onto ProjectWise.
Please Note: HorizonCAD Build Contains a Status Tool for Watermarks
9.3 Superseded deliverables
Where a deliverable is superseded by a new drawing number, the existing drawing shall be revised to
the next sequential revision, watermarked “Superseded“ with the new drawing number and the revision
description updated to reference the new drawing number
The new drawing number shall reference the superseded number in the revision description e.g.
‘Supersedes drawing BGP-GN-EL-0007-01’.
Drawings are then delivered to Document Control to be upload onto ProjectWise
Please Note: HorizonCAD Build Contains a Status Tool for Watermarks
9.4 File name
File names of drawings must follow the following conventions.
BRM-SS-EL-LAY-0001- CAD file name
01_Rev.dgn
BRM-SS-EL-LAY-0001- PDF file name
01_Rev.pdf
File names for legacy drawings
Existing drawings that have alpha-numeric file names (e.g. sdtcv01.dgn) should retain their file names
if they contain Reference Files or Raster Images. Renaming such files with attachments can break the
links from drafting software Bentley MicroStation. Files that do not have attachments shall be updated
to the Drawing Number captured on the drawing (e.g. SS174-100-1_Rev.dgn)
DM# 9118921 HPC-9CA-01-0002-2012 Page 14 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.10 STANDARDS DOCUMENTS AND NUMBERS
10.1 Standard drawings numbering
Standardised numbering conventions are required to manage standard drawings used in construction,
maintenance, projects and specifications, where quite often drawings reference other drawings. The
drawing numbering convention can be broken down in to a number of parts. Each part represents a
different step in the classification of the drawing type given in Table 10-1.
Table 10-1 Standard Drawing Number Convention
AAA - AA - AA - AAA - NNNN - NN
Unique
Doc. Sheet
HPA - SD - Discipline - - Sequence -
Type Number
Number
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example: HPA-SD-EL-LAY-0001-01
1. Location Code – HPA signifying Standard, refer to Appendix B
2. Facility Code – SD signifying Standard, refer to Appendix C
3. Discipline - The discipline selected will be the most appropriate for the content of the
document. Note that this is not necessarily the discipline that originates the document. Refer
to Appendix D
4. Document Type – For a list of document types, refer to Appendix E
5. Unique Sequence Number – Document Control will assign a four-digit unique sequential
number to all standard drawings, so each resulting number is unique from Table 10-2.
6. Sheet Number - Document Control will assign a two-digit sequential number
Table 10-2 Standard Drawing Number Convention
NNNN STANDARD DRAWING TYPE UNIQUE SEQUENCE
0000-0999 Distribution Overhead
1000-1999 Distribution Underground
2000-2999 Distribution General
3000-3999 Transmission Substation
4000-4999 Transmission Line
5000-5999 Transmission General
6000-6999 Generation Fossil
7000-7999 Generation Renewable
Drawing file name convention is DrawingNumber_VersionNumber.dgn
Example is:
HPA-SD-EL-LAY-0001-01_3.dgn for revision 3
HPA-SD-EL-LAY-0001-01_3.pdf for revision 3
DM# 9118921 HPC-9CA-01-0002-2012 Page 15 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.Examples of legacy standard drawing numbers1 superseded by this Section 10.1:
HPA-DL-S-3002-01
HPA-SD-E-0001-01
This example indicates that the drawing is for all of Horizon Power (HPA), the facility is distribution line
(DL) or Standard (SD), the discipline is structural (S) or electrical (E). The sequential number starts with
‘3’, so it is a general arrangement or ‘0’. The remainder of numbers are determined as required, the first
is the drawing number, and the last is the sheet number.
10.2 Distribution Standards Drawings
Drawings that are added to existing distribution design and construction manuals shall follow the legacy-
numbering format for that manual, e.g. Distribution Construction Standard, Distribution Substation
Manual, Distribution Design Catalogue.
An example of drawing number for the Distribution Construction Standard is shown below:
R3-1 (Title: Insulators - Reference chapter)
H16-2/4 (Title: LBS with bypass switch & 2 bushing TX - High Voltage chapter)
U9 (Title: Universal Pillar Installation Guide – LV Underground chapter)
The first letter indicates the chapter of origin (e.g. High Voltage chapter). The number
is the sequential drawing number within that chapter and ‘-x’ for sheets.
Drawing file name convention is DrawingNumber_VersionNumber.dgn
Format is AB-C-D_E e.g. R3-1_2.dgn or H16-2-4_3.dgn and same for .pdf
A – Chapter of the standard eg. R; H
B – Sequential number of construction type eg. 3; 16
C – Alternate construction type of same sequential number eg. 1; 2
D – Sheet number of drawing where multiple sheets (numeric) eg nil; 4
E – Revision number (numeric) eg, 2; 3, is separated by underscore “_”
An example of drawing number for the Distribution Substation Manual is shown below:
DSM-3-02 SHT 1
DSM-3-02 SHT 2
The first three letters indicate the manual of origin, the second number (3) indicates the chapter of origin
(Substation Arrangements). The final number is the drawing number. Drawings from this manual
frequently have multiple sheets, but the sheet number is not formally part of the drawing number.
Note: the Distribution Substation Manual is being gradually incorporated into the Distribution
Construction Standard as Chapter G.
1
Superseded standard HPC-9CA-01-0004-2013: Standard Drawing Numbers
DM# 9118921 HPC-9CA-01-0002-2012 Page 16 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.An example of drawing number for the Distribution Design Catalogue is shown below:
PO15 (Pole)
TX1-2 (Transformer)
LU11 (Universal Pillar)
The first portion (consisting of letters) indicate the chapter of origin (Transformers).
The remainder is the designation of the Compatible Unit (CU). Drawings from this
manual frequently address multiple CUs, which differ from each other by the bill of
materials.
For PO15 drawing revision 1, the drawing file name will be PO15_1.dgn
If there is more than 2 sheets on the drawing, the sheet numbers will be presented with a
dash and revision with an underscore for the filename. For example TX1 has sheet 1 and
sheet 2 on version 3, the drawing file names will be TX1-1_3.dgn and TX1-2_3.dgn
10.3 Distribution Standards Drawings Versioning
Note that Distribution Construction Standards have revision numbers as letters, for historical reasons.
When these are revised, they should be transitioned to numbered revisions. For example, an existing
drawing of revision C would be superseded by a new drawing marked revision 4.
The convention of the date on all distribution standards drawings and revisions will be
dd/mm/yy format.
10.4 Standards Document Numbering
A legacy system of standards document numbering will be retained since the convention has
been in use and cross-referenced in multiple documents that relate to compliance and
regulatory obligations.
The numbering format is contained in the Standards Register (DM#1918455) that is used to
maintain the currency and review period of standards within Horizon Power. Table 10-3
shows the numbering convention for standards documents.
Table 10-3 Standards Documents Number Convention
HPC - X A A - XX - NNNN YYYY
Doc. Engineering Work Sequential Registration
HPC - - Category -
Type Area Type Number year
Note: No spaces shall be created before or after any attribute; including the hyphen.
For Example: HPC-8DJ-12-0002-2019 – LV Connected Battery Energy Storage Systems
1. Location Code – HPC signifying Standard Document
2. Document Type – 8 signifying Specification
3. Engineering Area – D signifying Electrical
4. Work Type – J signifying Requirements
DM# 9118921 HPC-9CA-01-0002-2012 Page 17 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.5. Category – 12 signifying Generation Renewable
6. Sequence – 0002; Document Control will assign a four-digit sequential number to all
documents from the register (DM#1918455), so each resulting number is unique.
7. Year – 2019; year the standard number was generated and registered
Refer to the Standards Register (DM#1918455) for the numbering format and convention
details.
DM# 9118921 HPC-9CA-01-0002-2012 Page 18 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.11 DRAWING TITLING
Titles of drawings in general will conform to the five-line format as described within this specification.
All drawings shall be appropriately titled to clearly identify the location and item depicted by the drawing.
Existing drawings being revised which do not conform to the current specification titling are to be
updated to conform to this standard.
11.1 Titles
To standardise the approach of drawing titling and assist in the data base search functions. The
following shall apply:
1. Title Line 1 shall have the Geographical location, refer to Appendix B, e.g. KARRATHA
TERMINAL
No Deviation from these parameters shall be permitted
2. Title Line 2 shall be the Facility Type, Equipment Type or Switchyard Area, refer to
Appendix F
No Deviation from these parameters shall be permitted.
3. Title Line 3 shall contain a description of the type of drawing, refer to Appendix E Page
30 to 32
No Deviation from these parameters shall be permitted
4. Title Line 4 describe the area, item of plant or other information covered by the drawing.
It should include identification by circuit number, bay number or any other information to
describe the applicability of the drawings. The layout of the line should follow circuit
number, voltage, circuit type and description. The description may be 1 or 2 lines
5. Title Line 5 (Optional) As above
Some Typical Drawings (numbers and titles) as follows
Number DMP-SS-EL-MAT-0001-01
Title Line 1 DAMPIER SUBSTATION
Title Line 2 AUXILIARY POWER SUPPLIES
Title Line 3 MATERIAL LIST
Title Line 4 440V AC SUPPLY &
Title Line 5 CHANGEOVER BOARD
Number HDT-SS-EL-SCH-0001-01
Title Line 1 HEDLAND TERMINAL
Title Line 2 PROTECTION
Title Line 3 SCHEMATIC DIAGRAM
Title Line 4 HDT508 22kV REACTOR 52C
Title Line 5 DC PROTECTION
DM# 9118921 HPC-9CA-01-0002-2012 Page 19 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX A - REVISION INFORMATION
(Informative) Horizon Power has endeavoured to provide standards of the highest quality and would
appreciate notification of errors or queries.
Each Standard makes use of its own comment sheet which is maintained throughout the life of the
standard, which lists all comments made by stakeholders regarding the standard.
The document DM# 1539733 can be used to record any errors or queries found in or pertaining to this
standard, which can then be addressed whenever the standard gets reviewed.
Date Rev No. Notes
02/11/11 3 Added Location Codes for Rio Tinto Power Stations & Substations
01/12/11 4 Added Location Code for Carnarvon Solar Farm
25/01/12 5 Added Location Codes for Utah Point & Rottnest
24/05/12 6 Added Location Codes for new BHP Substations
30/05/12 7 Changed Document into a Standard
29/10/12 8 Reformatted and document and project numbering added
Renamed, reformatted and project document numbering modified and
21/01/13 9
new document types added
16/04/13 10 Added Location Codes for South Hedland Terminal
Document Revised to incorporate the addition of one more numerical
field in part 4 of the drawing number for the South Hedland Project,
10/05/13 11
and to split the project numbering and document numbering parts into
separate documents.
Removed location codes and referenced CS#10 for ‘single source of
29/10/14 12 truth’.
Added revision control
Changed title from Generating Drawing Numbers for New Sites post
Western Power to Drawing Numbers. Merged with GHD version 12.
07/12/17 13
Added new sections for Standards Drawings, WP standard template
drawings.
17/01/2018 14 New CS 10 Number
13/12/2019 15 Issued for Review
07/05/2020 16 Numbering and Titling Documents Updated and Combined.
Numbering and Titling Documents updated and combined.
26/05/2020 17 HPC-9CA-01-0003-2012 Drawing Titles and HPC-9CA-01-0004-
2013 Standard Drawing Numbers superseded by incorporating into
this standard.
DM# 9118921 HPC-9CA-01-0002-2012 Page 20 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX B - LOCATION CODES (NUMBERING & TITLING)
DMP-SS-EL-MAT-0001-01
CODE LOCATION TYPE
HPA HORIZON POWER REGION
AST ANDERSON STREET SUBSTATION SUBSTATION
AYN ARDYALOON COMMUNITY
AYN ARDYALOON POWER STATION POWER STATION
BLG BALGO COMMUNITY
BGB BEAGLE BAY COMMUNITY
BGB BEAGLE BAY POWER STATION POWER STATION
BEN BENTLEY TOWN
BEN BENTLEY SUBSTATION SUBSTATION
BYA BIDYADANGA COMMUNITY
BYA BIDYADANGA POWER STATION POWER STATION
BLA BILLILUNA COMMUNITY
BRM BROOME TOWN
BRM BROOME POWER STATION POWER STATION
BUL BULGARRA SUBSTATION SUBSTATION
LOM CAMBALLIN / LOOMA TOWN
LOM CAMBALLIN / LOOMA POWER STATION POWER STATION
CLB CAPE LAMBERT SUBSTATION SUBSTATION
CRN CARNARVON TOWN
CRG CARNARVON POWER STATION POWER STATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 21 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
CRD CARNARVON RENEWABLE - DERMS POWER STATION
CRN CARNARVON SUBSTATION SUBSTATION
CRL CORAL BAY TOWN
CRL CORAL BAY POWER STATION POWER STATION
CRS CORAL BAY SOLAR FARM SOLAR FARM
CRL CORAL BAY WIND FARM WIND FARM
CUE CUE TOWN
CUE CUE POWER STATION POWER STATION
DMP DAMPIER TOWN
DMP DAMPIER SUBSTATION SUBSTATION
DEN DENHAM TOWN
DNP DENHAM POWER STATION POWER STATION
DBY DERBY TOWN
DBY DERBY POWER STATION POWER STATION
DRN DJARINDJIN COMMUNITY
DRN DJARINDJIN POWER STATION POWER STATION
EKI EAST KIMBERLEY REGION
EPI EAST PILBARA REGION
ESP ESPERANCE TOWN
EHR ESPERANCE HARBOUR ROAD SUBSTATION SUBSTATION
EHR ESPERANCE POWER STATION POWER STATION
EHR ESPERANCE WIND FARM WIND FARM
EXP EXMOUTH TOWN
EXP EXMOUTH POWER STATION POWER STATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 22 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
FDS FAIRWAY DRIVE SUBSTATION SUBSTATION
FIT FITZROY CROSSING TOWN
FIT FITZROY CROSSING POWER STATION POWER STATION
BRM FREDERICK STREET SUBSTATION SUBSTATION
GPR GAP RIDGE SUBSTATION SUBSTATION
GAS GASCOYNE REGION
GJN GASCOYNE JUNCTION TOWN
GJ GASCOYNE JUNCTION POWER STATION POWER STATION
HC HALLS CREEK TOWN
HC HALLS CREEK POWER STATION POWER STATION
HDR HARDING RIVER DAM SUBSTATION SUBSTATION
HDT HEDLAND TERMINAL TERMINAL
HTN HOPETOUN TOWN
HTP HOPETOUN POWER STATION POWER STATION
BPS IPP - BOODARIE POWER STATION POWER STATION
BKN IPP - BROCKMAN SUBSTATION SUBSTATION
CBS IPP - CAPE LAMBERT BULK SUPPLY POWER STATION
DBS IPP - DAMPIER BULK HANDLING SUB SUBSTATION
DMS IPP - DAMPIER MAIN SUBSTATION SUBSTATION
FIH IPP - FINUCANE INNER HARBOUR SUB SUBSTATION
FIN IPP - FINUCANE ISLAND SUBSTATION SUBSTATION
FOH IPP - FINUCANE OUTER HARBOUR SUB SUBSTATION
GWY IPP - GOLDSWORTHY SUBSTATION SUBSTATION
HPS IPP - HEDLAND POWER STATION POWER STATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 23 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
HDS IPP - HOPE DOWNS SUBSTATION SUBSTATION
HBI IPP - HOT BRIQUETTE IRON POWER STATION POWER STATION
JAD IPP - JUNA DOWNS SUBSTATION SUBSTATION
KRP IPP - KARRATHA POWER STATION POWER STATION
LPS IPP - LAMBERT POWER STATION POWER STATION
MAO IPP - MARANDOO SUBSTATION
MSM IPP - MILLSTREAM SUBSTATION
MSM IPP - MILLSTREAM SUBSTATION SUBSTATION
NPS IPP - NELSON POINT SUBSTATION SUBSTATION
NGA IPP - NIMINGARRA POWER STATION
PWA IPP - PANAWONICA SUBSTATION
PDC IPP - PDC OTHER
BHP IPP - PORT HEDLAND SUBSTATION SUBSTATION
RYL IPP - ROY HILL SUBSTATION SUBSTATION
SGP IPP - SHAY GAP SUBSTATION SUBSTATION
SRY IPP - STRELLEY SUBSTATION SUBSTATION
TPE IPP - TOM PRICE TOWN
WAS IPP - WEST ANGELES SUBSTATION
WCT IPP - WICKHAM 1 OPERATIONS POWER STATION POWER STATION
JGL JIGALONG COMMUNITY
KLU KALUMBURU COMMUNITY
KLU KALUMBURU POWER STATION POWER STATION
KRT KARRATHA TOWN
DM# 9118921 HPC-9CA-01-0002-2012 Page 24 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
KTP KARRATHA TEMPORARY POWER POWER STATION
KTS KARRATHA TEMPORARY SUBSTATION SUBSTATION
KRT KARRATHA TERMINAL TERMINAL
KIM KIMBERLEY REGION
KUN KUNUNURRA TOWN
KPC KUNUNURRA PARRYS CREEK SUBSTATION SUBSTATION
KUG KUNUNURRA POWER STATION POWER STATION
KUN KUNUNURRA SUBSTATION SUBSTATION
LAK LAKE ARGYLE TOWN
LAK LAKE ARGYLE SUBSTATION SUBSTATION
LAV LAVERTON TOWN
LAV LAVERTON POWER STATION POWER STATION
LEO LEONORA TOWN
LEO LEONORA POWER STATION POWER STATION
MLB MARBLE BAR TOWN
MLB MARBLE BAR POWER STATION POWER STATION
MKA MEEKATHARRA TOWN
MKA MEEKATHARRA POWER STATION POWER STATION
MEN MENZIES TOWN
MEN MENZIES POWER STATION POWER STATION
MID MIDWEST REGION
MMG MOUNT MAGNET TOWN
MMG MOUNT MAGNET POWER STATION POWER STATION
MNM MOUNT NEWMAN MINING SUBSTATION SUBSTATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 25 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
MGP MUNGALLAH POWER STATION POWER STATION
MRO MURCHISON RADIO ASTRONOMY POWER STATION
MDR MURDOCH DRIVE SUBSTATION SUBSTATION
NRS NORSEMAN TOWN
NRS NORSEMAN POWER STATION POWER STATION
NUL NULLAGINE TOWN
NUL NULLAGINE POWER STATION POWER STATION
ONS ONSLOW TOWN
OWP ONSLOW POWER STATION POWER STATION
OLT ONSLOW SOLAR SOLAR FARM
OLT ONSLOW TOWN ZONE SUBSTATION SUBSTATION
ORD ORD RIVER HYDRO POWER STATION POWER STATION
PBO PARABURDOO TOWN
PCK PEGS CREEK SUBSTATION SUBSTATION
PIL PILBARA (NWIS REGION
PSN POINT SAMPSON TOWN
PSN POINT SAMPSON SUBSTATION SUBSTATION
PHD PORT HEDLAND TOWN
RPS REDBANK POWER STATION POWER STATION
ROE ROEBOURNE TOWN
ROE ROEBOURNE SUBSTATION SUBSTATION
RTP ROTTNEST ISLAND REGION
RTP ROTTNEST ISLAND POWERSTATION POWER STATION
SAN SANDSTONE POWERSTATION POWER STATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 26 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE LOCATION TYPE
SAN SANDSTONE TOWN
SHP SOUTH HEDLAND POWER STATION POWER STATION
SHT SOUTH HEDLAND TERMINAL TERMINAL
GLD SOUTH REGION REGION
SWC SOUTH WEST CREEK SUBSTATION SUBSTATION
SHL STOVEHILL SUBSTATION SUBSTATION
UTP UTAH POINT SUBSTATION
WBN WARBURTON COMMUNITY
WRN WARMUN COMMUNITY
WRN WARMUN POWER STATION POWER STATION
WFD WEDGEFIELD SUBSTATION SUBSTATION
WKI WEST KIMBERLEY REGION
WPI WEST PILBARA REGION
WCT WICKHAM TOWN
WIL WILUNA TOWN
WIL WILUNA POWER STATION POWER STATION
WYN WYNDHAM TOWN
WPS WYNDHAM EMERGENCY POWER STATION POWER STATION
WYN WYNDHAM SUBSTATION SUBSTATION
YAL YALGOO TOWN
YAL YALGOO POWER STATION POWER STATION
YGA YUNGNORA COMMUNITY
YGA YUNGNORA POWER STATION POWER STATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 27 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX C - FACILITY CODES (NUMBERING)
DMP-SS-EL-MAT-0001-01
CODE FACILITY
BS BATTERY ENERGY STORAGE SYSTEM
DE DEPOTS
DL DISTRIBUTION LINES
GF GEOTHERMAL FARM
GS GENERATION SYSTEMS ( SPS)
HF HYDRO FARM
HG HYBRID GENERATION SYSTEM
HY HYDROGEN POWER STATION
PS POWER STATIONS
SD STANDARD ** ONLY USE FOR HP STANDARD NUMBERING**
SF SOLAR FARM
SS SUBSTATIONS AND SWITCHYARDS
TF TIDAL FARM
TL TRANSMISSION LINES
WF WIND FARM
DM# 9118921 HPC-9CA-01-0002-2012 Page 28 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX D - DISCIPLINE CODES (NUMBERING)
DMP-SS-EL-MAT-0001-01
CODE DESCRIPTION
AD ADMINISTRATION
AR ARCHITECTURAL
BD BUSINESS DEVELOPMENT / STRATEGIC MARKETING
CI CIVIL
CS COMMISSIONING
CM COMMUNICATION SYSTEMS
CN CONSTRUCTION/CONSTRUCTION MANAGEMENT
CO CONTRACTS
DC DOCUMENT CONTROL
EL ELECTRICAL
EN ENVIRONMENTAL
EP EPCM
ES ESTIMATING
FA FABRICATION
FI FINANCE
GE GEOLOGY & GEOTECHNICAL
HS HEALTH & SAFETY
HR HUMAN RESOURCES
IM INFORMATION MANAGEMENT
IS INFORMATION SYSTEMS/ICT
IX INSPECTION SERVICES
DM# 9118921 HPC-9CA-01-0002-2012 Page 29 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
IC INSTRUMENTATION & CONTROL
LA LANDSCAPE
LO LOGISTICS AND MATERIAL MANAGEMENT
MA MAINTENANCE
ML MATERIALS/METALLURGY
ME MECHANICAL
MT METERING
MD MULTI DISCIPLINE
OP OPERATIONS
PA PLANNING APPROVALS AND LAND DEVELOPMENT
PC PROJECT CONTROLS AND PLANNING
PI PIPING
PM PROJECT MANAGEMENT
PT PROCUREMENT
QA QA/QC
RI RISK
SD SAFETY IN DESIGN (ENSMS)
SR SAFETY & RISK
SC SCADA
SE SECURITY
ST STRUCTURAL
SU SURVEYING /GIS
DM# 9118921 HPC-9CA-01-0002-2012 Page 30 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX E - DOCUMENT AND DRAWING TYPES (NUMBERING &
TITLING)
DMP-SS-EL-MAT-0001-01
CODE DESCRIPTION
PROJECT MANAGEMENT
AGC AGREEMENT
AGN AGENDA
COE CLOSE OUT EVALUATION
FNO FILE NOTE
FRM FORM
HDD HANDOVER DOSSIER
IMG IMAGE
IST INSTRUCTION
LTR LETTER
MEM MEMORANDUM
MOM MINUTES OF MEETING
PHT PHOTO
ORG ORGANISATION CHART
POS POSITION DESCRIPTION
PRS PRESENTATION
PPL PROPOSAL / TENDER SUBMISSION TO CLIENT
SOW SCOPE OF WORK AND/OR SERVICES
STR STRATEGY
DM# 9118921 HPC-9CA-01-0002-2012 Page 31 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
PROJECT CONTROLS
BUD BUDGET
CST COST REPORT
CTR COST TIME RESOURCE
EST ESTIMATE
PCR PROJECT CHANGE REQUEST
PGR PROGRESS REPORTS
VAR VARIATION
WBS WORK BREAKDOWN STRUCTURE
CONTRACTS
ADD RFP ADDENDUM
AWL CONTRACT AWARD COVER LETTER
BKG BANK GUARANTEE
CBE COMMERCIAL BID EVALUATION
CDA CONFIDENTIALITY DEED/AGREEMENT
CEC CONTRACT EXECUTION CHECKLIST
CLA CLARIFICATION/DEPARTURE
CLM CLAIM
COT CONDITIONS OF TENDERING
CRV CONTRACT VARIATION
CTS CONTRACT SECURITY
DM# 9118921 HPC-9CA-01-0002-2012 Page 32 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
DEE DEED OF SETTLEMENT
EOI EXPRESSION OF INTEREST
EVL TENDER EVALUATION
EXC EXECUTED CONTRACT
INV INVOICE
ITT INVITATION TO TENDER
LOI LETTER OF INTENT
MOU MEMORANDUM OF UNDERSTANDING
NOD NOTICE OF DELAY
NOV NOTICE OF VARIATION
NSP NOTICE OF SUCCESSFUL PROPOSAL
NUP NOTICE OF UNSUCCESSFUL PROPOSAL
PCO PURCHASE ORDER
POP PROPOSAL OPENING RECORD
POR PURCHASE ORDER REQUISITION
PQL PRE-QUALIFICATION
PRC PROGRESS CLAIM
QTE SUPPLIER QUOTATION
RFA RECOMMENDATION FOR AWARD
RFS RECOMMENDATION FOR SHORTLIST
RFI REQUEST FOR INFORMATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 33 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
RFP REQUEST FOR PROPOSAL
RFQ REQUEST FOR QUOTATION
SDR SUPPLIER DATA REQUIREMENTS (SDRL)
SOR SERVICE ORDER
SSJ SOLE SOURCE JUSTIFICATION
TBE TECHNICAL BID EVALUATION
TDP TECHNICAL DEVIATION PROPOSAL / CONCESSION REQUEST
TRA DOCUMENT TRANSMITTAL
VAQ VARIATION APPROVAL REQUEST
WCO WORKS CONTRACT
QUALITY
ALT SAFETY ALERT
CKL CHECKLIST
AUD AUDIT REPORT
CAR CORRECTIVE ACTION REQUEST
CAT CALIBRATION AND TEST RECORD
FAT SUPPLIER TESTING DOCUMENTS
FTC FUNCTION TEST CERTIFICATE
GDE GUIDE
IAI INSPECTION ASSESSMENT INSTRUCTION
ITP INSPECTION & TEST PLAN
DM# 9118921 HPC-9CA-01-0002-2012 Page 34 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
ITR INSPECTION & TEST REPORT
NCR NON-CONFORMANCE REPORT
POL POLICY
PRO PROCEDURE
PQS SUPPLIER PRE-QUALIFICATION
QAN QUALITY ALERT NOTICE
QSS QUALITY SHOP SURVEY
WOI WORK INSTRUCTION
DOCUMENT CONTROL
DRF DRAWING REQUEST FORM
PDM PROJECT DISTRIBUTION MATRIX
TEM TEMPLATE
ENGINEERING
AEL AUTHORISED ENGINEERS LIST
BOD BASIS OF DESIGN
BOM BILL OF MATERIALS
CAL CALCULATION
CER CERTIFICATE
CHT CHART
COC CERTIFICATE OF COMPLETION
CPK CONSTRUCTION WORK PACK
DM# 9118921 HPC-9CA-01-0002-2012 Page 35 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
DEC DESIGN CRITERIA
DAS DATASHEET
EDQ EQUIPMENT DATA QUESTIONNAIRE
ENM ENGINEERING ANALYSIS MODEL
FLC FLOWCHART
FRP FORTNIGHTLY REPORT
HMS HAZARDOUS MATERIAL SCHEDULE
HZR HAZARD REPORT
IDX INDEX
IOM INSTALLATION AND OPERATIONS MANUAL
JOB JOB BOOK / DOCUMENT INDEX
LST LIST (E.G. EQUIPMENT, LINE TIE-INS, BATTERY LIMITS ETC.)
MAN MANUAL
MAP MAPS
MTX MATRIX
MDL MASTER DOCUMENT LIST
MDR MANUFACTURER'S DATA REPORT
MRP MONTHLY REPORT
MST METHOD STATEMENT
MTO MATERIAL TAKE OFF
PHI PHILOSOPHY
DM# 9118921 HPC-9CA-01-0002-2012 Page 36 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
PLN PLAN
REC RECORD
REF REFERENCE
REG REGISTER
REQ REQUISITION
RPT REPORT
SCO CONTRACT SPECIFICATION
SDL SUPPLIER DOCUMENT / DRAWING LIST
SFT SOFTWARE
SPC SPECIFICATION
SRL SUPPLIER REQUIREMENT LIST
SST STANDARD SPECIFICATION
TEN TECHNICAL NOTE /STUDY
TQR TECHNICAL QUERY
VIP VALUE IMPROVEMENTS
WRP WEEKLY REPORT
DRAFTING (DRAWING TYPES)
ALM ALIGNMENT SHEET
APL AREA PLAN
AMT ARRANGEMENT
ASY ASSEMBLY
DM# 9118921 HPC-9CA-01-0002-2012 Page 37 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
BLK BLOCK DIAGRAM
CPT CONCEPT DRAWING
CON CONNECTION DIAGRAM
DES DESCRIPTIVE
DET DETAIL
DNG DRAINAGE DRAWING
ELE ELEVATION
FND FOUNDATIONS
GAR GENERAL ARRANGEMENT
HAZ HAZARDOUS AREA
INS INSTALLATION DETAIL
INC INTERCONNECTION DIAGRAM
KEY KEY DIAGRAM
LAY LAYOUT
LSP LIGHT & SMALL POWER
LOC LOCATION PLAN
MAF MANUFACTURER DRAWING
MAT MATERIAL LIST
MOD MODEL
NET NETWORK DIAGRAM
OIN OVERHEAD INSTALLATION
DM# 9118921 HPC-9CA-01-0002-2012 Page 38 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
ONE OVERHEAD NETWORK
OSE OVERHEAD SERVICES
PIP PIPING SUPPORT DRAWING
PLA PLAN
PFD PROCESS FLOW DIAGRAM
PRF PROFILE DRAWING
RAT RATING DIAGRAM
RPL ROUTE PLAN
SCD SCHEDULE
SCH SCHEMATIC DIAGRAM
SEC SECTION DRAWING
SFD SIGNAL FLOW DIAGRAM
SLD SINGLE LINE DIAGRAM
SIP SITE PLAN
SUT SITE UTILISATION
SIW SITE WORK
SKT SKETCH
STW STEELWORK DRAWING
SYS SYSTEM FUNCTION DIAGRAM
TAB TABLE
TER TERMINATION DIAGRAM
DM# 9118921 HPC-9CA-01-0002-2012 Page 39 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
UIN UNDERGROUND INSTALLATION
UNE UNDERGROUND NETWORK
UGS UNDERGROUND SERVICES
WID WIRING DIAGRAM
CONSTRUCTION
CIR CONSTRUCTION INSPECTION REPORT
COS CONSTRUCTION STRATEGY
FCN FIELD CHANGE NOTICE
FIR FIELD INSPECTION REPORT
FQY FIELD QUERY
JSA JOB SAFETY ANALYSIS
POB PERSONS ON SITE REGISTER
SIN SITE INSTRUCTION
SQR SITE QUERY
COMMISSIONING
CDR DAILY REPORT
CMM COMMISSIONING METHOD STATEMENT
CMS COMMISSIONING MANAGEMENT SYSTEM GENERATED DOCUMENT
CPL COMMISSIONING PUNCH LIST
CPS COMMISSIONING PARAMETER SETTINGS
CRP COMMISSIONING REPORT
DM# 9118921 HPC-9CA-01-0002-2012 Page 40 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.CODE DESCRIPTION
COM COMMISSIONING PROCEDURE
CWP COMMISSIONING / COMPLETIONS WORK PACK
DOS COMMISSIONING DOSSIER
NOE NOTICE OF ENERGISATION
OTP OPERATION TEST PROCEDURE
TRN TRAINING DOCUMENTS
DM# 9118921 HPC-9CA-01-0002-2012 Page 41 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.APPENDIX F - DRAWING TITLE REFERENCES
FACILITY TYPE, EQUIPMENT TYPE OR SWITCHYARD AREA
***Line TWO of the Title***
DESCRIPTION REMARK
ALARMS SCHEMATICS
AUXILIARY POWER SUPPLIES AC SUPPLIES & DISTRIBUTION
BUILDING INTERNAL PLANS
BATTERY ENERGY STORAGE SYSTEM
BUSBARS DRAWINGS ASSOCIATED WITH RIGID BUSBARS
CIRCUIT BREAKERS
CAPACITOR BANKS
COUPLING CAPACITORS
CONDUCTORS
CIVIL
SCHEDULES & ACCESSORIES (INCLUDING SEALING
CABLING ENDS)
CONSUMER MAINS
INCLUDES TERMINAL PALMS, ADAPTOR PLATES &
CONNECTORS SPACERS
COMMUNICATIONS INCLUDES PILOT WIRE SYSTEMS
CONTROL PANELS MIMIC TYPE
CONTROL SCHEMATICS
CABLE TRENCHES
DM# 9118921 HPC-9CA-01-0002-2012 Page 42 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.DESCRIPTION REMARK
CURRENT TRANSFORMERS
CURRENT & VOLTAGE TRANSFORMERS COMBINED CT & VT
CABLE TRAYS
DC SUPPLIES
DEPOTS
DISCONNECTOR
DISTRIBUTION NETWORK
DISTRIBUTION SUBSTATION
DISTRIBUTION CONNECTION
EARTHING
EARTHING COMPENSATORS
ELECTRICAL CONTROL ROOM
EQUIPMENT ENCLOSURES MARSHALLING BOX, FUSE BOX
ELECTRICAL RESTRICTED USE
EARTH SWITCH
FENCES
FIRE PROTECTION
GEOTHERMAL FARM
GENERAL PROPERTY DETAILS ETC.
GENERATION SYSTEMS
HYDRO FARM
DM# 9118921 HPC-9CA-01-0002-2012 Page 43 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.DESCRIPTION REMARK
HYBRID GENERATION SYSTEMS
HEAT RECOVERY SYSTEM
HYRDOGEN POWER STATION
INTERCONNECTION LINES
INSULATORS
INSULATOR SET HARDWARE
LABELS SCHEDULES AND DETAILS
LIGHTING
LANDSCAPING
LINE TRAPS
MICROGRID
METERING
PROTECTION CUBICLE ARRANGEMENT & WIRING DIAGRAMS
PROTECTION RACKS ARRANGEMENT & WIRING DIAGRAMS
PROTECTION SCHEMATICS
POWER STATION
REACTORS
ROADS
RTU CUBICLE
SWITCHBOARD
SCADA
DM# 9118921 HPC-9CA-01-0002-2012 Page 44 of 54 Print Date 25/05/2020
© Horizon Power Corporation
Uncontrolled document when downloaded. Refer to CS10 for current version.You can also read
