OPERATOR'S MANUAL Models SPY80-1P / SPY80-1S Push Spreader - Spyker Spreaders
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
OPERATOR'S MANUAL Models SPY80-1P / SPY80-1S Push Spreader Spyker Spreaders Contact us at 800.972.6130 www.spyker.com ! ! IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 1 1017629-D
Table of Contents + Safety TABLE OF CONTENTS OPERATE SAFELY Safety ����������������������������������������������� 2 Read Before Using: Part List �������������������������������������������� 3 • Keep bystanders away when you operate this machine. Hardware Identifier ��������������������������� 4 • Use this machine for intended purpose only. Part Explosions ����������������������������� 5-7 • Do not let children or an untrained person operate machine. Assembly ����������������������������������� 8-14 • Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts. Calibration ���������������������������������� 15-17 • Do not modify the machine or safety devices. Unauthorized Operation Instructions ���������������� 18-19 modifications to the machine may impair its function and Dial Settings������������������������������������ 20 safety, and void the warranty. Grass Seed Spreading Chart ��������� 21 • Do not let anyone sit or ride on equipment during operation. • Wear substantial footwear and long trousers. Do not Troubleshooting������������������������������� 22 operate the equipment when barefoot or wearing open sandals. Warranty ����������������������������������������� 24 • Do not wear loose fitting clothing that can get caught in moving parts. • Always wear eye protection when operating the equipment. • Stay alert for holes in the terrain and other hidden hazards. • Watch out for traffic when crossing or near roadways. • Before you operate any feature of this machine, observe your surroundings and look for bystanders. • Always wash hands after contact with fertilizers and pesticides. • Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition. • Always remove material from hopper before attaching spreader on a vehicle-mounted spreader caddy. ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 2 1017629-D
Part List DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 No. Part # Qty Description No. Part # Qty Description 1 1006084 5 Bolt, HexHd 1/4x3/4 SS 1017618 1 Handle, Lower - Stainless 54 4 1017543 1 Plate, Linkage 1017621 1 Handle, Lower - Black 5 1017501 1 Bracket, Linkage 57 1017504 2 Cap, Plastic 7 1017340 1 Control Linkage Assembly 58 L-1744-6 1 Label, Serial#, Spyker 9 1001255 1 Screw 1/4-20 X 1”HexHd, SS 1017329 1 Stand, Large Frame - Stainless 59 10 1017551 1 Bolt,HexHd 1/4-20 x 1.50 1017507 1 Stand, Large Frame - Black 11 1017503 1 Spring, Gate 1017328 1 Large Frame Weldment - Stainless 60 12 1008431 1 Rate Gate Link, Formed 1017508 1 Large Frame Weldment - Black 13 1017580 1 Plate, Hopper Bottom 63 1001607 2 Wheel, 12” Drive/Idle 14 1004880 4 Bolt, HexHd 1/4x1/2 SS 64 F-283 2 Bearing, Axle 15 1000203 1 Hopper Bottom Bearing 69 1017629 1 Manual 16 1001526 1 Accuway Adjustment Screw 70 1017578 1 Cover, Hopper 80# 17 1001525 1 Accuway Adj. Nut Bracket 71 1017546 1 Screen, 80# 18 1000210 1 Rate Gate 72 1017500 1 Hopper, 80# 19 1001523 1 Accuway Diffuser 73 1008067 1 Decal Spyker Square Blue 20 1001521 2 Guide, Rate Gate/Accuway 74 1001386 1 Spyker Accuway Label 21 1000215 1 Pine Tree Clip 76 1017776 1 Support Bracket 22 1000211 1 Dial Mount 23 1000213 1 Dial, Plastic 77 1018577 1 Parts Bag 24 1000198 2 Felt Washer 25 1000223 1 Agitator Wire 2 1001554 9 Washer, Nylon 26 1000054 1 Roll Pin 1/8 X 7/8 3 1005198 23 Nut, Nylon Lock 1/4-20, SS 27 1005211 1 Spinner Plastic Lg Black 6 1001533 2 Nylon Flange Bushing 28 1008078 1 Axle, Spinner 8 1001351 7 Washer, 1/4” SS 29 1001301 2 3/8 Spinner Shaft Bushing 44 1001262 10 Bolt, HexHd 1/4x1-1/2 SS 30 1001516 1 Bevel Gear-metal 45 1007828 2 Knob, Handle 31 1000053 1 Roll Pin 1/8 X 3/4 46 1017345 1 Lever, Control 32 1001518 1 Pinion Gear - Metal 47 1017346 1 Spring, Control Lever 33 1001299 2 Gearbox Bushing 5/8” 50 1017344 1 Control Lever Stop 34 1005389 1 Nylon Spacer, Pin Retain 51 1007888 4 Bolt, HexHd 1/4x2-1/4 SS 35 1001304 1 Dowel Pin, 3/16 x 1, SS 52 1017371 1 Bolt, HexHd, 1/4x3-1/4 SS 36 1008085 1 Axle, Wheel 53 1017617 1 Plate, Guide 37 1005336 1 Gear Box Cover Front 55 45M1111SS 6 Washer, Flat, SS-5/16” 38 1005337 1 Gear Box Cover Rear 56 1001315 4 Nut, Nylon Lock 5/16-18 39 1005368 1 Grease Zerk 1/4 Drive IN 61 1005414 1 Rue Ring Locking Pin 40 1017710 8 Bolt, PhlpHd 10-24x5/8” SS 62 1001350 5 Washer, Flat SS 41 1001308 8 Nut, Nylon Lock, #10-24 SS 65 1001274 1 Clevis Pin, 3/16x1-3/4 42 1000225 2 Handle Grip 66 1019596 1 Cotter Ring 1017620 1 Weldment, Handle - Stainless 43 67 1008811 2 Bolt,Hex 5/16-18x1 SS316 1017623 1 Weldment, Handle - Black 68 1017374 2 Bolt, Carriage, 5/16x3/4 48 1017502 1 Linkage 75 1017725 2 Lock Washer Ext/Int Tooth 5/16 49 1000000 1 On-off Decal ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 3 1017629-D
Hardware Identifier DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER 2 Washer IDENTIFICATION OF HARDWARE DURING ASSEMBLY. Nylon (x10) ��������������������������������� 1001554 Nut: Nylon Lock 3 1/4”-20 (x23) �������������������������������������� 8 Washer 1005198 SS 1/4” (x7) ��������������������������������� 1001351 Nut: Nylon Lock, SS 41 #10-24 (x8) ����������������������������������������� Washer: 1001308 24 Felt (x2) ������������������������������� 1000198 Nut: Nylon Lock 56 5/16”-18 (x4) ������������������������������������� 1001315 55 Washer: Flat SS 5/16” (x6) ��������������������������� Flange Bushing 45M1111SS 6 Nylon (x2) ������������������������������������� 1001533 62 Washer: Flat SS (x5) ����������������������������������� 1 Bolt: Hex Head, SS 1001350 1/4 x 3/4” (x5) ��������������������������� 1006084 75 Lock Washer: 5/16 Ext/Int Tooth (x2) ����������������������� Bolt: Hex Head 10 1/4-20 x 1.50 (x1) ��� 1017225 1017551 * Exterior circumference of washers can vary. These dimensions are a measurement of the 14 Bolt: Hex Head, SS internal diameter of the washer. 1/4 x 1/2” (x4) �������������������������������� 1004880 Bolt: Hex Head, SS 44 1/4 x 1-1/2” (x10) ��������������������������������������������������������������������������������������������������� 1001262 51 Bolt: Hex Head, SS 1/4 x 2-1/4” (x4) �������������������������������������������������������������������������������� 1007888 52 Bolt: Hex Head, SS 1/4 x 3-1/4” (x1) �������������������������������������������������������� 1017371 67 Bolt: Hex Head, SS Bolt: Carriage 68 5/16-18 x 1” (x2) ����������� 5/16 x 3/4” (x2) ������������������� 1008811 1017374 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 4 1017629-D
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 5 1 3 76 4 RATE GATE + AXLE / SPINNER 8 60 3 5 3 6 7 1 1 8 2 9 1 10 3 12 13 14 = 11 3 2 8 3 3 15 23 18 20 22 16 19 17 21 24 25 27 26 28 41 = 38 24 29 31 37 32 33 35 39 34 33 36 30 40 = ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 5 1017629-D
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 FRAME & HANDLE 42 42 43 46 2 45 45 44 2 3 49 3 8 51 52 3 47 48 3 50 51 2 6 8 44 44 44 53 3 3 54 8 3 56 55 75 55 75 56 67 55 55 67 68 68 56 60 55 55 56 51 57 51 57 63 63 3 3 61 57 65 64 62 62 59 62 64 66 36 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 6 1017629-D
Part Explosions DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 69 HOPPER 70 71 44 44 2 2 2 2 72 74 73 3 3 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 7 1017629-D
ASSEMBLY Remove the Part List (page 3) / Hardware Identifier (page 4) and set aside for frequent reference during assembly. For reassurance, Hardware Iden tifier lay the nuts, bolts and washers down DO NOT RE TUR N PRO DU CT IF YO U AR on page 4 to verify ILLUST RAT ION IDENTI FICATI S ON THIS PAG ON OF HA RD E AR E TO SC ALE FO R FAS E MIS SIN G PAR TS. PLE AS E CA LL: 1 (80 0) 972 -6130 you’re using the WA RE DU RIN TER G ASS EM BLY Washer . 2 Nut: Nylon Nylon (x10) correct parts during 3 Lock ��������� 1/4”-20 (x2 10 0155 4 ������� 3) � � � � � � 10 05198 ��������� ���� assembly. Nut: Nylon 8 Washer 41 Lock, SS SS 1/4” (x7 ) ������� #10-24 (x8 10 01351 ��������� ) ������� 10 01308 ��������� ���� 24 Washer: 56 Nut: Nylon Lock Felt (x2) � 5/16”-18 (x4 ��������� )�������� 10 00198 ������ 10 01315 ��������� �� 6 Flange Bush Washer: Fla ing 55 t Nylon (x2) SS 5/16” (x6 ��������� ) ������� 10 01533 ��������� ������� 45 M1111SS 30 (80 0) 972- 61 SE CA LL: 1 S. PLEA IN G PA RT Bolt: Hex He IF YO U AR E MI SS 1 ad Washer: Fla PR OD UCT 1/4 x 3/4” (x5 , SS 62 t SS (x5) � Part List RE TU RN )�������� ��������� DO NOT 10 06 084 ������ ������� 10 0135 0 ription Qty Desc10 Bolt: Hex He ad Part # 1/4St-20ainles s x 1�5 Lock Wash No. Lower - 0 (x1) � � 75 er: 1 Handle, 10175 ck Bla51 Ex t/Int Tooth 5/16 8 Lower - (x2) � � � � � tion 101761 Handle, 1017225 ���� ��� Qty Descrip 1 1 sti c 54 101762 Ca p, Pla Bo Part # 2 14 lt: yker rial#, SpHex Head No. x3/4 SS 17504 bel, Se1/4 ,sSS xHd 1/4 10 La x 1/2e - St ain les 5 Bolt, He 57 1 rge Fram ” (x4) � � � � � � � � * Exte rior circ umf 4 kage L-1744-6 Stand, La 10 04Fr88 e - Black ��������� These dim ens eren ce of was hers can vary 100608 Plate, Lin 58 1 1 1 9 rge am0 s inte rnal diam ions are a mea . 101754 3 Lin ka ge 101732 Stand, La - Stainles eter of the was sure men t of the Bracket, ly 1 W eldment her. 4 1 Assemb 59 50 7 rge Fr am e 101750 1 Control Linkage 1017 1 44 La Bolt: He me nt - Black 5 1 exHd, SS 8 Frame W x eld Head, SS 0 -20 X 1”H 101732 La rge1/4 x 1-1 101734 Screw 1/4 1.50 1 ive/2” /Idle(x10) 7 1 Hd 1/4 -20 x 60 101750 8 el, 12” Dr ��������� 100125 5 Bolt,Hex 2 Whe10 0126 ��������� 9 1 100160 7 , Axle 2 ��������� ��������� 101755 1 Gate Bearing Spring, rmed 63 2 ��������� 10 1 Link, Fo F-28 3 Bo Manu lt: Hex He al ���� 10 17503 Ra te Gate 64 51 1 80 # ad, SS 11 1 ttom 1/4 pp er 1 pper Bo 10 17629 ver,xHo 2-1 /4” 100843 Plate, Ho 69 1 Co (x4 ) ������� 12 1 1/4 x1 /2 SS 17 57 8 10 07888 n, 80 # � � � � � ��������� 101758 0 xHd 10 Scree ��������� Bolt, He 70 1 13 4 Bearing 101754 6 80# ��������� 100488 0 Bottom Hopper, uare Blu e � 14 Hopper ent Screw 71 1 Bolt: l He yker Sq Deca Sp x Head 1 0 52 3 y Ad jus tm 101750 , be SS 100020 Accuwa t 72 1 1/4 x 3-1 y La l 15 1 t Bracke 100806 7 yker Ac /4” wa cu (x1) 100152 6 y Adj. Nu 1 10Sp ��������� Accuwa 73 1737ort ��������� 16 5 1 te 100138 6 Supp 1 Bracket ��������� 100152 Rate Ga 74 1 � 17 1 r 6 0 y Diffuse 101777 67 Bolt: Hex He 100021 Accuwa way 76 ad , SS 18 1 te/Accu 5/16-18 x 1”g 100152 3 Rate Ga 19 2 Guide, rts Ba (x2) � � � � � � 01521 Clip 1 08Pa 10 10 Pin e Tr ee 101857 7 811 Bolt: Carria 20 1 Nylon 68 ge 5 unt 77 Washer, SS 100021 Dial Mo 9 1/4-20, 5/16 x 3/4” 21 1 100155 4 lon Lock (x2) � � � � � 100021 1 stic 2 Nut, Ny ����� Dial, Pla 23 Bushing 1017374 22 1 her ©2 198 Spy 05017 Flange 100021 3 Felt Was 3 10 ker 2Spreaders Ny lon 23 2 3 /A Bri1/4nly ” SS -Hardy Co 100153 Washer, -1/2 SS. 00198 ire 10 Ag itator W 6 7 24 1 1 d 1/4x1 Page 4 22 3 1/8 X 7/8 100135 lt, HexH 1000 Roll Pin ck 8 10 Bo 25 00054 1 stic Lg Bla 100126 2 Knob, Ha nd le 10 Sp inner Pla 44 2 26 1 8 ntrol 1017629-D 100521 1 inner 100782 Lever, Co 27 1 Axle, Sp Bu shing 45 1 Lever er Sh aft 101734 5 Control 100807 8 3/8 Spinn 46 1 Spring, 28 2 op 1 ar-metal 17346 ol Lever St 29 100130 Bevel Ge 47 10 1 Co ntr x2-1/4 SS 1 X 3/4 4 d 1/4 01516 101734 xH ll Pin 1/8 Bolt, He 30 10 1 Ro 50 4 x3-1/4 SS 00 05 3 Ge ar - Metal 10 07888 lt, He xHd, 1/4 31 10 1 Pinion 5/8” 51 1 Bo 8 Bushing 101737 1 ide 100151 Gearbox Retain Plate, Gu 32 2 52 1 -5/16” 9 acer, Pin 101761 7 Flat, SS 100129 Nylon Sp Washer, 33 1 6 x 1, SS 53 6 5/16-18 100538 9 , 3/1 45M111 1SS lon Lock 34 1 Dowel Pin 55 4 Nut, Ny Pin 4 heel 5 Locking 100130 Axle, W 100131 Rue Ring 35 1 Co ve r Front 56 1 t SS 5 x 4 Fla 100808 Gear Bo 100541 Washer, 36 1 Rear 61 5 /4 100533 6 x Cover 0 , 3/16x1-3 Gear Bo 100135 Clevis Pin 37 1 Drive IN 62 1 100533 7 Zerk 1/4 4 ng Grease SS 100127 Cotter Ri 6 38 1 -24x5/8” 65 1 1 SS31 100536 8 lpHd 10 6 5/16-18x Bolt, Ph SS 101959 Bolt,Hex 39 8 ck , #10-24 66 2 6x3/4 101771 0 Nut, Ny lon Lo 100881 1 rriage, 5/1 5/16 40 8 67 2 Bolt, Ca t To oth ip t/In 10 01308 ndle Gr less 101737 4 asher Ex 41 2 Ha le - St ain 68 2 Lock W 100022 5 nt, Hand 5 42 1 Weldme - Black 101772 0 Handle 75 101762 W eldment, 1 D 1017629- 3 43 101762 Linkage 1 2 cal 48 101750 On-off De 1 00 00 0 49 10 Page 3 rdy Co. ers/A Brinly-Ha yk er Spread ©2017 Sp ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 8 1017629-D
Assembly 1. After removing all the parts from your box, place the 3. Add 1 washer (62) to the wheel axle (36), then slide pre-assembled hopper portion in your work area. on the tire (63) and another washer (62). Start upside down and facing this direction: NOTE: If necessary, add the provided additional washer to reduce play in the axle. Fig. 1 Secure in place with the Rue Ring Locking Pin (61). (See figures 3b and 3c below). Start with this side. 62 36 62 63 Fig. 3 61 61 2. Add 2 washers (62) to the wheel axle (36). Slide on the tire (63). 61 If last washer does not fit, remove tire & one of the interior washers. Lock the wheel in place with the Clevis Pin (65) and Cotter Ring (66). Fig. 3b Fig. 3c 66 4. Run two Hex Head bolts (51) through the frame (See Fig. 4 for alignment). Lower the tubing for the 62 stand (59) on the bolts and secure in place with two Nylon Lock Nuts (3). Tighten completely with a 7/16” socket & wrench. 65 63 59 51 3 51 Front 3 Fig. 2 Fig. 4 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 9 1017629-D
Assembly FLIP SPREADER OVER 7. Add the Handle Weldment (43) by lining it up on the Lower Handle tubing from step 6. Secure the Handle in place by running four Hex 5. Align the two holes of the Lower Handle (54) with the two holes of the outer, rear edges of the Frame Head Bolts (44) through the two handle ends from (60). Place one of the Lock Washers with teeth (75) the outside. Tighten with four Nylon Lock Nuts (3) between the square hole of the Handle (54) and the from the inside of the Lower handle (60). curved slot on the Frame (60). Tighten with a 7/16” socket & wrench. Starting from the inside of the Frame, run a Carriage Bolt (68) through the curved slot of the Frame (60). 44 The Carriage Bolt will also pass through the square hole of the Lower Handle (54) and the end will be facing out. Loosely secure with a washer (55) and a Nylon Lock Nut (56). Use a 1/2” Socket & Wrench. Repeat on the 3 other side. 43 Do NOT tighten (yet). 60 44 60 54 68 Fig. 7 56 55 75 8. Setting the spreader handle height. Determine the angle / height you will want your handle. (At the highest point, the handle will be 37” off the ground. At the lowest point, the handle will Fig. 5 be 32” off the ground). TA LL 6. Add one washer (55) to a hex head bolt (67). Starting ES T SE from the outside edge, run the bolt through the circular TT holes of the Lower Handle & Frame, then loosely secure IN G with another washer (55) & a Nylon Lock Nut (56). SHO RTE Use a 1/2” Socket & Wrench. Repeat on the other side. ST S ETT ING Do NOT tighten (yet). 54 60 Fig. 8 67 55 55 56 Tighten the hardware from steps 5 & 6 completely with a 1/2” socket & wrench. Fig. 6 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 10 1017629-D
Assembly 9. Adding the Control Lever Stop. 43 Orientation is very important on this step. - The Control Lever Stop (50) needs to be centered 50 over the three holes on the right side of the handle. 51 (Same side as the On/Off sticker). 43 - Leave the 3 51 center hole 8 open and run 50 two hex head bolts (51) through the outer two holes of the Handle Weldment (43). Bolts should also pass Fig. 9c Fig. 9a through the Control Lever Stop (50) and two 1/4” washers (8). - The lip of the the Control Lever Stop (50) needs to be POINTED OUT & AWAY from the handle - Add two Nylon Lock Nuts (3) on the ends of the tubing. (See Fig 9b). Bolt (51). Verify the Control Lever Stop is centered (see Fig 9a) before tightening the Nuts (3) completely, securing everything in place. 10. Adding the linkage bar. Slide the Linkage bar (48) into the Linkage Assembly (7) from the side from left to right at a 50 43 low angle, then lift it up toward the handle. (See Fig. 10b). 48 48 48 Fig. 9b 7 Fig. 10a Fig. 10b ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 11 1017629-D
Assembly 11. Adding the Linkage Guide. 12. Using Fig. 12 as a guide, insert a Hex Head Bolt Orientation is very important on this step. (44) through the remaining hole at the top of the Lower Handle (54). For this step, please follow the illustration notations The bolt (44) should pass through the oval hole of below: the Linkage Guide (53) and a washer (8). Loosely secure in with a Nylon Lock Nut (3). 53 Do NOT tighten (yet). 48 Fig. 12 44 Fig. 11a Use the lower, circular hole of 48 the Linkage Guide (53) and add it to the Linkage bar (48). 8 3 53 53 48 13. a) Adding the Control Lever Start to slide a hex head bolt (52), through the remaining center hole on the handle Fig. 11b Slightly lower linkage (48). Slide guide (53) down linkage & under the lower handle (60). End of the bolt comes out through the side of the handle with the On/Off sticker and the Control Lever Stop (50) that was added on Step 9. 48 Do NOT push the bolt 100% through (yet). 53 At a sideways angle, slide the bottom hole of the Control Lever onto the Linkage Bar (48). See Fig. 13a b) Twist the Control Lever toward the hopper and then up, aligning the center hole of the Lever Fig. 11c Lift the linkage (48), aligning the with the bolt (52) that was added in the last step. top hole of the guide (53) with the Push the bolt (52) through the Control Lever. hole of the lower handle (60). See Fig. 13b ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 12 1017629-D
Fig. 13a 52 14. Checking the Rate Gate Ensure the rate gate closes completely when the gate control lever is pulled back and locked 48 into place. Fig. 13b 52 After adding the Control Lever to the Linkage Rod (48), rotate the lever forward Fig. 14 into the ON position and push the bolt (52) through. 48 15. Rate Gate Adjustment If the gate IS closed, skip to step 16. Fig. 13c If it is NOT closed, follow these steps: 52 a) Ensure the hopper is empty. b) Turn the Spyker dial to #9. Remove the spring 47 tension on the gate control lever by moving the 2 lever to the Open position. 3 6 48 50 51 c) Add the Nylon Flange Bushing (6) to the bolt. 51 *Be sure to have the extended notch of the Flange facing the Lever. Push the small extended notch of the Nylon Flange Bushing (6) into the center hole of the assembled Control Lever. OPEN (Dial Setting at 9) OPEN (View From Above) Add the Control Lever spring (47) to the rest of the exposed bolt. Loosely keep parts in place c) Loosen the two bolts (51) that attach the control with a Nylon Washer (2) & a Nylon Lock Nut (3). lever stop (50). d) Slide the control lever stop (50) forwards very slightly, then retighten bolts (51). Do NOT tighten (yet). ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 13 1017629-D
Assembly e) Move the gate control lever to CLOSED and re- 17. Checking / Adjusting *Front of evaluate the rate gate. If it is closed, then no the Accuway Spreader further adjustment is necessary. f) If the rate gate is still open, then repeat steps 3-5 until the gate is closed. 16 Fig. 15a Start rotating the Accuway Adjustment Screw CLOSED (Dial Setting at 1) CLOSED (View From Above) (16) clockwise. Continue to rotate the ACCUWAY Adjustment 16. Tighten the Bolts Screw (16) clockwise (Fig. 15a) until the Accuway is out of view while looking down into the hopper The center bolt that runs through the Control Lever (Fig. 15b). needs to be tightened enough to keep the Lever secure, but also be free enough to function. This Control Lever Stop (50) can shift a little up or down the length of the handle as needed. 50 Fig. 15b 70 44 18. Final Step Place the Screen 71 (71) down inside the hopper. 72 53 Secure the Linkage Guide (53) in place by Attach the Hopper tightening the bolt (44) that goes through the lower Cover (70) by hooking handle. (See step 12 on page 12 for clarification). it around the rim of the Hopper (72). *Bolt can remain slightly loose, allowing Linkage Guide to move. ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 14 1017629-D
Calibration ! READ BEFORE USING Spreader Calibration - Two items must be considered when calibrating a spreader: 1. First, is the DISTRIBUTION PATTERN of the 2. Second, is the PRODUCT APPLICATION RATE. spreader. This is the pattern the product makes as This is the amount of product applied per thousand it strikes the ground after being broadcasted from square feet. This is important because over- the spreader’s spinner. There are many factors that application can be costly and may cause plant injury, affect the distribution pattern of a rotary spreader while under application will reduce the effectiveness and some of them relate directly to the material. For of the material. this reason, it is recommended that the spreader be calibrated separately for every material. 3. Set the Spyker dial to the correct dial position (see WARNING: Avoid Injury! the dial settings chart on page 20). ! Chemicals can be dangerous. Avoid injury to operators or bystanders. 4. Align the spreader approx. 20 feet in front of the gap in the row of pans. How to Test for a 5. Push the spreader approx. 3 mph, and open the Uniform Distribution Pattern: gate lever approx. 15 feet before pans. 6. Push the spreader through the gap in the pans, 1. Lay out shallow boxes or pans in a row on a line then close the hopper lever about 5 feet past the perpendicular to the spreader’s travel direction. In pans. the middle of the row, leave a gap wide enough for the spreader to be pushed through. 7. Repeat steps 4-6 approx. 15 times or until enough material is in the pans so that it can be measured. 8. For each pan, record the distance from the end of the pan to the center line and weigh the material. RH 1 RH 2 RH 3 RH 4 RH 5 CENT ER LI RH 6 NE . CENT ER LI RH 7 NE . CENT ER LI NE 2. To conduct the test, begin with the Accuway completely rearward, and not in the way of the gate plate opening. Continues on page 14... ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 15 1017629-D
Calibration ! READ BEFORE USING How to Test for a Uniform Distribution Pattern: ( ...continued from page 15). CHART A LH LH LH LH LH LH LH RH RH RH RH RH RH RH CENTER PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN PAN 7 6 5 4 3 2 1 1 2 3 4 5 6 7 DISTANCE FROM CENTER WEIGHT OF MATERIAL 9. Review the recorded weights. Ideally for an Adjusting the Accuway even distribution, LH Pan NOTE: Moving the Accuway plate will shift the material on the spinner. Adjustment is very 1 and RH Pan 1 would sensitive & should be done in small increments until the spread pattern is centered. have approximately the same material. The same for LH Pan 2 and RH Pan 2, etc. 10. If the spreader pattern is not even, then adjust the Accuway according to these charts and repeat steps 3-9. Travel Please adjust in very small increments, as the Accuway is Spread HEAVY to the Left HEAVY to the Right very sensitive. Pattern Turn dial & shift Accuway Turn dial & shift Accuway to the back half of the opening. to the front half of the opening. (front) ↑ (front) ↑ How to Adjust the Accuway Setting: ↓ (handle) ↓ (handle) ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 16 1017629-D
Calibration ! READ BEFORE USING How to Set the Correct Product Application Rate (Spyker Dial Setting): Complete “How to Test for a Uniform Distribution Pattern” (pages 15-16) to ensure distribution is even. 1. Once distribution is even, use the same data in 5. Weigh 20 lbs. of product and place it in the spreader Chart A (pg 16) to complete the steps below. hopper. Place Spyker Dial at #4 position. Spread material over the distance necessary to equal the 2. Find the pan on both the LH and RH side of the linear distance found in step 4 (Ex. 125 ft.). center that has approximately 50% of the amount of material as the center pan. Example: While you are spreading, ensure you are traveling at a constant speed, usually 3 mph. A. Center Pan has 0.25lb of material. 6. Weigh the product left in the hopper and subtract B. Divide .25 lb / 2 = 0.125 lb this amount from the amount with which you started. C. Find the LH and RH pan with The result is the application rate for this product in approximately 0.125 lbs of material. pounds per 1,000 sq. ft. 3. The effective pattern width is the distance from the A. Example: LH pan to the RH pan found in step 2. To find the 20 lbs – 10 lbs (left over in hopper effective width, find the distance between the LH after spreading for 125 ft) pan and RH pan. = 10lbs A. Example: 7. Adjust the Spyker dial up or down as needed and LH Pan = 48” from center repeat this procedure until the correct application RH Pan = 48” from center rate is achieved. Total Width = 96” (8 ft) Remember, speed is important, so 4. Find the linear distance needed to spread 1,000 ensure the speed you calibrate your NOTE: sq. ft, taking into consideration the effective pattern spreader is the same speed that width. you travel during actual use. A. Example: 1,000 sq ft / 8 ft (effective width) = 125 ft. B. Measure out a linear distance equal to 125 ft. ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 17 1017629-D
Operation Instructions ! WARNING: AVOID INJURY! Chemicals can be dangerous. Avoid injury to operators or bystanders NOW YOU ARE NOW YOU ARE READY TO SPREAD READY TO PUT MATERIAL IN THE HOPPER • Keep spinner blade clean. Excess material build-up can cause an uneven spread pattern. • Keep the spinner blade level when spreading. • Make sure the rate gate is in the closed position. • DO NOT overload. Maximum capacity of these models is 80 lbs. • Read chemical • DO NOT use on windy days. container label for handling instructions. • Spread header strips at the ends of the area OPPOSITE of the A Material Safety Data Sheet direction of spreading. This will provide a “turn-around” area, an (MSDS) should be supplied by area to re-align the spreader for the return spread. the chemical dealer and • Example shown is for 6 ft. wide spread. Make the first spread pass provides proper safety at one-half the spread width from the edge of the spreading area or information. in this case, approximately 3 feet (or one big step). • Wear proper clothing and • Additional spreading passes will be at the full spread width or safety equipment while approximately 6 ft. apart. handling or applying chemicals. • TAKE A SIGHTING AT THE FAR END. Keep your eye on the sighting as you spread. You will not need to wonder where you are • Prohibit all smoking, drinking, or where you have been. Continue until spreading is completed. and eating around chemicals. • Leftover fertilizer can be spread under trees and other high feeding • When spreading products areas without showing “edge of spread” lines. containing herbicides, exercise extreme caution with respect to careless spreading Tip: When not and to wind-drift. Contact Of spreading (and if Some Products On Some pushing the spreader Header Plants Can Be Fatal. some distance) tip • Fill the spreader on a flat, the spreader so only level surface only. Fill on the idle wheel is on sidewalk, driveway, cardboard, the ground. etc. to avoid material loss. • When filling hopper with 3’ 6’ 6’ material, always use screen to help break up clumps. Header ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 18 1017629-D
Operation Instructions TIPS: • Become familiar with the spreader before you put • Some products can be fatal to some plants material in the hopper. • Always remove material from hopper before attaching • Practice walking with the spreader, opening and spreader on a vehicle-mounted spreader caddy. closing the rate gate at the appropriate times. • If a dial setting is not found, use the size and weight • Travel at a constant speed and operate the spreader comparison table found in this manual. Determine a lever position. Remember: Open the rate gate after dial setting on the low side. If the setting proves to be the spreader is in motion at operating speed (about 3 too low, cover the area more than one time. A higher mph, or at a brisk walking pace). setting can be used when a proven dial setting is established. • Close the rate gate while spreader is still at operational speed. NOTE: Published dial settings are approximate only. The operation of the spreader, the condition • The spread width ranges from 4 - 12 ft. wide depending of the material (damp or dry or over-pulverized) and on the density of the material and the operators weather conditions, are all contributing factors. For walking speed. these reasons, it is often a good idea to spread the • The spread thins or feathers at the outer edges, area 2 times - or one-half rate - in cross directions eliminating sharp, “Edge Of Spread” lines which (SEE INFORMATION ON ONE-HALF RATE DIAL cause stripes and streaks. Extra coverage can be SETTINGS ON PAGES 20-21). One-half rate dial given under trees and other heavy feeding areas settings are highly recommended under damp without showing “Edge Of Spread” lines. and humid conditions. AFTER USE / CLEANING THE SPREADER: CLEAN AND OIL SPREADER IMMEDIATELY AFTER EACH USE METHOD #1 METHOD #2 NOTE: Good “Dry Cleaning” (Method #1) is preferable to poor “Wet Cleaning” (Method #2). Wipe Wash, rinse, spreader and dry the spreader. • It is virtually impossible to have rust and corrosion on a thoroughly clean, dry, oiled surface. Note: Drying takes time. with an oily • Again - just before using - oil all bearings & moving parts. Moisture trapped in bearing cloth. Oil all areas is slow to go. • In storage, ideally the spreader should be hung by the bearings and handle. In any case, do not pile weight on the spreader, as bearing Immediately after drying excess weight over a period of time can distort the tires. areas. - oil all bearings and moving parts. Make certain all operations are thorough. Oil Bearings and All Moving Parts Make sure the spreader is running freely! ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 19 1017629-D
Dial Settings Rate Dial NOTE: DIAL SETTINGS ARE APPROXIMATE ONLY! The settings shown in the charts below are for reference only. For initial settings that will result in true pounds per 1,000 sq ft, please return to “How to set the Correct Product Application Rate” on page 19. The RATE DIAL has 9 numbers with 10 stops between each number. This allows for accurate control of the spreading rate. The dial is set with only a turn, it will automatically lock into the set position. LINE UP THE DIAL NUMBER WITH THE DIAL INDICATOR. WARNING: When spreading products containing herbicides, exercise extreme caution with respect to ! careless spreading and to wind-drift. Use the rotary agitator only if needed. Free-flowing, lump-free materials will not require the agitator. The rotary agitator is easily installed or removed. Note the clockwise rotation and sweep. Place felt washer around spinner shaft before inserting agitator. DIAL DIAL RATE GATE Lbs. DIAL SETTINGS PARTICLE SETTINGS SETTINGS PRODUCT per 1000 SIZE Full Rate Half Rate sq. ft. Once Over Twice Over LESCO SPYKER SETTINGS SETTINGS 1 3.6 3.1 Fine 2 4.0 3.5 Pellets 3 4.2 3.7 23 5.5 22 5.2 Mixed 2 3.7 3.2 21 4.9 Fine 4 4.7 4.1 Pellets 20 4.6 6 5.2 4.5 19 4.3 2 3 2.2 18 4.0 Small 4 4.2 3.7 Pellets 17 3.7 6 4.5 4 16 3.5 Medium 1 3.5 3 15 3.2 Nitrogen 2 4.2 3.7 14 2.9 Pellets 3 4.7 4 13 2.5 2 3.5 3 12 2.2 Medium Pellets and 4 4.2 3.8 11 1.9 Granuals 6 5.2 4.5 10 1.6 2 3.8 3.3 9 1.1 Large Heavy 4 4.9 4.1 Pellets 6 5.9 4.9 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 20 1017629-D
Grass Seed Spreading Chart GRASS SEED SPREADING CHART The settings shown in this chart are for reference only. For initial settings that will result in true pounds per 1,000 sq ft, please see the Operation Instructions on page 18. Bag Sq. Ft. Dial Setting Dial Setting Spread Product Weight Coverage Full Rate Half Rate Width Blue Grass or Red Top 0.5 lbs 1,000 1.25 - 4 1 lb 1,000 2.0 - 4 2 lbs 1,000 2.5 - 4 Park, Merion, Delta or Kentucky Bluegrass 0.5 lbs 1,000 2.5 - 4 1 lb 1,000 3.0 - 4 2 lbs 1,000 3.5 - 4 Hulled Bermuda 2 lbs 1,000 2.75 2.25 6 3 lbs 1,000 3.0 2.5 6 4 lbs 1,000 3.25 2.75 6 Mixtures Including Coarse Seeds 2 lbs 1,000 6.0 - 6 4 lbs 1,000 7.0 - 6 6 lbs 1,000 7.0 - 6 Rye Grasses or Tall Fescue 2 lbs 1,000 6.0 - 6 4 lbs 1,000 7.0 - 6 6 lbs 1,000 7.75 - 6 Dichondra 4 oz. 1,000 1.9 - 8 8 oz. 1,000 2.1 - 8 12 oz. 1,000 2.5 - 8 Pensacola Bahia 4 lbs 1,000 4.5 3.75 7 5 lbs 1,000 4.75 4.0 7 6 lbs 1,000 5.0 4.25 7 ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 21 1017629-D
Troubleshooting TROUBLESHOOTING / FREQUENTLY ASKED QUESTIONS Problem Diagnosis Solution Thoroughly wash out hopper and shut off plates with water. Ensure debris is not stuck between shut off plate and rate gate plate. Rate gate is binding and will not Rate gate is jammed - Very slightly loosen bolt 1017551 (10) open/close properly. with debris. allowing linkage 1017340 (7) to float. - Very slightly loosen screw 1001255 (9) allowing linkage 1017340 (7) to float. - Slide bracket 1017776 (76) to the left or right. There is not an even distribution Reference the Accuway adjustment The Accuway is not set properly. coming from the spreader. chart on page 16 of this manual. Lever control is slow to open or Lever Control (46) is rubbing against Loosen spring (47) by loosening locknut there is a grinding noise. the Control Lever Stop (50). (3). See fig 13C. Lever control is making a Linkage (48) is rubbing against the Loosen guide plate (53) and grinding noise. Guide Plate (53). adjust up/down. Question Solution Is there a Deflector available Yes! We have a Deflector that is sold separately. Part # SPYFD-80100 for this product? Please visit our website for more info: spyker.com The Accuway Adjustment Screw (16) is a small black screw with a rectangular head, located on the front of the Spreader. This screw controls the direction of What is the difference between the distribution. See page 16. the Accuway and Rate Gate? The Rate Gate Dial (23) is a white circular knob on the back of the Spreader. This dial controls the amount of distribution. See page 20. For initial setup, please reference step 17 of the assembly (on page 14) and then How do I use the Accuway? calibrate your spreader. See calibration steps: pages 15-17. To adjust your Accuway settings, refer to the chart on page 16. ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 22 1017629-D
Notes ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 23 1017629-D
WARRANTY 1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase. Spyker Spreaders will not be liable for any loss, damage or expense including, but not limited to, consequential or incidental damages, arising from the operation, condition or use of the item. The sole and exclusive remedy against Spyker Spreaders being the replacement of the defective parts. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This express warranty, which is applicable only to the original purchase, is in lieu of and excludes all other warranties, whether expressed or implied by operation of law or otherwise, including any warranty of merchantability or fitness for particular purpose. SPYKER SPREADERS Jeffersonville, IN 47130 USA Phone: 800.972.6130 www.spyker.com ©2021 Spyker Spreaders/A Brinly-Hardy Co. Page 24 1017629-D
You can also read