Worktops Product information - Pronorm
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
Worktops P C Product information The texture of stone and wood reproductions varies in different areas in both pattern and colour. This is what gives them their true-to-life appearance. Stone designs consist of a natural stone reproduction, printed in high quality colours via a sophisticated procedure. The design is a replica of the natural stone and the variations in shade, colour and structural nuances present in the natural stone are therefore faithfully reproduced. These natural variations in shade and colour, which provide this design with its particular charm, may under certain circumstances be particularly evident in the area of the joint between two worktops. These variations are unavoidable with natural stone reproductions and are not due to a manufacturing defect. Owing to the manufacturing process, a texture that is continuous and uniform in colour at worktop joints is impossible. They merely emphasise the individual, natural character of the worktop. Storage: Worktops should always be stored at an ambient temperature of 18-22° C and a relative humidity of 50-65%. Likewise, they should be stored in a horizontal position. If worktops must be stored exceptionally in a vertical position, they should be stood on the rear edge. Transport: In general, the criteria listed under „storage“ also apply to transportation. The transport protection should only be removed immediately before assembly. Cutouts: Cutouts should be performed exclusively with a manual surface milling cutter. If compass saws must be used in individual cases, the corners must be bored out. Sharp corners result in crack formation in the laminate and should therefore be avoided. Ovens / Dishwashers: Steam from ovens and dishwashers places heavy stresses on the worktop lower edge. Damage due to humidity results over time. For automatic opening dishwashers (Eco-Mode), no liability is accepted for damage caused by swelling. Areas with increased levels of moisture should be protected against vapour with aluminum tape (AZ 1072). Particularly important is the joint between edge band and the worktop. Worktop edges: Water or other liquids must be wiped away thoroughly from the worktop edging, otherwise the liquid may penetrate into the joint and result in swelling. Important, it is essential to wipe the worktop lower edge too. Worktop joins: Water or other liquid must not be allowed to remain on the joint between two worktops. In spite of the good seal, the humidity may penetrate after a period, resulting in swelling in this area. Upstand: Water must not run between the worktop and wall. This is avoided by applying upstands during assembly. The various upstand versions must be injected with sealing material. (Principally in the sink and hob areas.) Wood edging: Worktop edging is subject to very high stresses. The wood edging should therefore be sealed particularly thoroughly with acrylic or polyurethane lacquer. Drops of water on the wood edging must be wiped away immediately. Maintenance information for the consumer: Humidity (water and other liquids, damp sponges) on the joints must be removed immediately. Hot saucepans, baking trays or pans damage the laminate surface of the worktops. Please therefore always use a mat. Cutting on the worktops always results in scratches and a cutting board should always be used. We recommend watersoluble household detergents to clean and care for synthetic worktops. Wipe the surfaces evently with a clean, damp, lint-free cloth. Subsequently rub with a very slightly moistened window leather or Vileda window leather without exerting excessive pressure. Important: Never use scourers or solvents for nitrocellulose lacquer, acetone, nail varnish remover or similar products. These products will leave smears that are difficult to remove. P/C - 09/2019 10.53
Worktop decor 2020 P C
Standard (S)
225 oxide 295 bronze 315 stone grey
320 dark cement 590 oak end-grain natural 605 light grey
Important: Different zones are very noticeable
in decor and colour. Due to very noticeable
colour differences not available with post-formed
edge.
730 oak marcato 775 oak sepia 915 denver oak
1707 Concrete dark 1714 Black 2106 Soapstone black
10.54 P/C - 09/2019
Worktop decor 2020 P C
Standard (S)
2109 Raja Slate Matt 2118 Catania oak 2122 Catania oak grey-brown To suit surround
To suit surround decor 865 Catania oak. decor 895 Catania oak grey-brown.
2125 Sonoma oak natural 2130 Vesuv light 2134 Arlington oak natural
2139 Concrete greybrown 2140 Concrete arkosa 2141 Provence oak
2142 Arctic white 2147 Concrete natural 2148 Tessina
To suit surround decor 125 arctic white.
P/C - 09/2019 10.55
Worktop decor 2020 P C
Standard (S)
2150 Onyx grey 2151 Eramosa black 2152 Cement grey
To suit surround decor 665 onyx grey. To suit surround decor 360 cement grey.
2154 dark ceramic 2155 light ceramic 2156 oak end-grain
Important: Different zones are very noticeable
in decor and colour. Due to very noticeable
colour differences not available with post-formed
edge.
2157 marble grey 2169 Black structure 2170 Arctic White structure To suit surround
decor 125 arctic white.
N N N
3150 Marble terramo 8070 Vintage oak 8080 Evoke Sunset
10.56 P/C - 09/2019
Worktop decor 2020 P C Fenix (FX) 2160 Fenix arctic white 2161 Fenix Nero 2162 Fenix super-white matt laminate (MX) 3070 Marble Breccia Paradiso 3080 Marble Carrara 3090 Marble el Greco 3100 Marble Roma P/C - 09/2019 10.57
Worktop edging and colour variations P C
16 mm thick
A1-..-16 Edging in worktop finish
Front edge with PP edging
1,5 mm thick.
2 x R = 2 mm
The recess height increases
accordingly.
39 mm thick
A4-..-03 Edging in worktop finish
Front edge postformed. Not available in:
2 x R = 3 mm 320 dark cement
and
Important: 2152 Cement grey
The following decors have
radius 2 x R = 6 mm:
2009 White
A4-..-16 Edging in worktop finish
Front edge with PP edging
1,5 mm thick.
2 x R = 2 mm
57 mm thick
57
A6-..-08 Edging in worktop finish
Front edge with laminate edging.
The appearance of a worktop 57 mm
thick is achieved via the doubled
frame construction.
The recess height is reduced
accordingly.
10.58 P/C - 09/2019
Worktop edging and colour variations P C
95 mm thick
95
A10-..-08 Edging in worktop finish
Front edge with laminate edging.
The appearance of a worktop 95 mm
thick is achieved via the doubled frame
construction.
The recess height is reduced
accordingly.
P/C - 09/2019 10.59
You can also read
