CADDY CORPORATION Tray Make-Up Conveyor Systems - Food Service Equipment
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
CADDY CORPORATION
Food Service Equipment Air Systems
Tray Make-Up
Conveyor
SystemsITEM NO:
CADDY Food Service Systems
page 1 of 1 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
"XL" SERIES
Single track powered unit for time-saving tray completion in
medium to moderately large institutions. Elevated conveyor
bed reduces operating space, cuts down on stretching and
COFFEE DOME
turning to lessen fatigue.
AND MUG COVER
MODEL DISPENSER DISPENSER
MILK AND
XL-1 ICE CREAM
SINGLE TRACK DISPENSER
POWERED
recommended for
institutions with
150 TO 400 BEDS COLD
FOOD
UNIT
TRAY TRAY
STARTER HOT
DELIVERY
FOOD
UNIT TRUCK
HOT
FOOD HEATED
UNIT PLATE
DISPENSER
HEATED UTILITY
UNDERLINER CART
DISPENSER
Double track powered unit for maximum efficiency in large
COFFEE
hospitals. Serves as two conveyors in one without requiring
URN
large extra floor space. Trays are served from both sides
STAND
simultaneously, thus double tray production.
MODEL
XL-2
DOUBLE TRACK HOT
POWERED FOOD
recommended for UNIT
institutions with
400 TO 650 BEDS
ICE CREAM
DISPENSER
MUG
HEATED DISPENSER
UNDERLINER TOASTER
DISPENSER CADDY
COLD
FOOD HEATED
UNIT PLATE
DISPENSER
BEVERAGE
DISPENSER CADDY CORPORATION
TRAY 509 Sharptown Road P.O. Box 345
STARTERS Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-1 SERIES
long tray pick-up area, with limit switch activated by
stainless steel lever protruding through slot in belt bed. Belt
to be driven only on top surface of conveyor bed. No drain
pans. All bearings to be heavy duty ball-type, with sealed
lubrication.
Conveyor bed to be 14 gauge stainless steel of
welded construction, ground and polished. Conveyor bed
height to be 42 1/2" and to elevated over support equipment.
Structural Supports to be stainless steel and welded
to underside of conveyor bed. Conveyor to be provided with
a screwed in place access panel at tail end providing access
to bearings.
FEATURES Drive housing to consist of 18 gauge stainless steel
x Elevated design to accommodate tray assembly support enclosure on two sides with removable 18 gauge panels.
equipment underneath, thereby saving 15-20% floor Conveyor belt to direct drive by variable speed motor with
space as compared to conventional assembly lines. range of belt speed 5 to 40 feet per minute rated for
x Single track powered unit for time-saving tray completion 120/208/60/3 phase, 4 wire plus separate ground.
in medium to moderately large institutions. Motor to be controlled manually through an on/off
x Elevated conveyor bed cuts down on stretching and push-button switch and automatically through a limit switch,
turning to lessen fatigue. both located at discharge end. All wired to splashproof SCR
controller with low voltage and overload protection. All
SPECIFICATIONS: electrical components above, as well as the motor, to be
Series XL-1 EXPRESS LINE Tray make-up conveyor to be completely interwired through waterproof flex conduit and
as manufactured by Caddy Corporation Unit shall be 19" splashproof conduit connectors, terminating in waterproof
wide x ________ long, and to accommodate flat bottom circuit breaker panel(s).
trays up to 15" wide. (Specify dimensions of trays to be Leg assembly of 16 gauge tubular stainless steel 1
used.) 5/8" O.D. and 1" O.D. crossbracing completely welded.
Conveyor belt to consist of dual 1/2" diameter (Continue specifications by selecting stationary or mobile model)
Dura-San belting. Belting itself is USDA accepted, highly
Stationary Unit
resistant to abrasion, dirt, oil and most chemicals, maintains
tension without springs, sprockets or links, continuous Fitted with adjustable stainless steel bullet feet.
without ends or mechanical connection devices. Start end to Mobile Unit
be provided with 6" long tray rest. discharge end to have 20" Fitted with 5" diameter polyurethane tired casters, two with
brakes. Conveyor shall have 6'-0" long power cord.
NOMINAL LENGTH
11 3/4" 2'-0"
1'-6 3/4"
1'-3 1/2"
1 3/4" 1 3/4"
3'-6 1/2"
3'-6 1/2"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-1 SERIES
Optional Features: Double Overshelf for Storage of Cookies, Crackers,
Desserts, etc.
Wireway with Factory Installed Electric Outlets
Double overshelf to be Model ACC-6015 and to set on
Caddy-veyor to be furnished with a stainless steel wireway
curbing of conveyor. To be approximately 5'-0" long with two
recessed under conveyor bed with removable screw cover.
shelves 15" wide of 16 gauge stainless steel turned down 1"
Wireway will distribute to power risers locate at each leg
on all four sides, supported by splayed legs of 1" O.D. 16
assembly. Both sides of power riser to be provided with
gauge stainless steel tubing with guides at bottom to slide to
moisture-proof electric outlets with hinged covers for
any convenient location.
adjoining mobile equipment, all as indicated on plan. Outlets
wired to one or more circuit breaker panels with each Overhead Starter Shelf
receptacle having its own circuit breaker control with manual
Overhead tray starter shelf to be Model T-565 and to set on
reset feature and shut-off. All electrical work to be ready for
curbing of conveyor. To be approximately 3'-0" long with
single final connection by others to a circuit breaker panel at
the job site. sloped shelf of 16 gauge stainless steel turned down 1" on
Specify number of outlets, as well as voltage, phase, front and back. Cutout in shelf to accommodate three pans
wattage or motor size and location for each electrical plug-in 4" deep. Mounted on legs of 1" O.D. 16 gauge stainless
outlet required. Preferred input voltage is 120/208v, 3ph, 5 steel tubing with guides at bottom to slide to any convenient
wire system including ground. location.
*IMPORTANT NOTE ON ELECTRICAL DATA* Undermount Starter Shelf
Maximum allowable amperage for mobile tray make-up
Undermount tray starter shelf to be Model T-566 and to be
conveyor is 100 amps 3 phase. If total amperage exceeds
mounted under conveyor bed with two 14 gauge stainless
100 amp, 3 phase, a second circuit breaker panel will be
steel brackets. To be approximately 3'-0" long with sloped
require. A separate electric connection is needed in the field
shelf of 16 gauge stainless steel turned down 1" on front and
for EACH circuit breaker panel on the conveyor.
back. Cutout in shelf to accommodate three pans 4" deep.
Removable Work and Storage Shelf for Advance
Make-Up of Soup and Beverages
Stainless Steel Pans
Work and storage shelf to be Model ACC-2010 made of 16
gauge stainless steel flanged up at rear and both sides. A set of 3 stainless steel pans (one full, two 1/3 pan) for
Shelf supported by stainless steel tubular leg with adjustable T-565 or T-566
stainless steel bullet foot. Shelf size to be 20" X 10". Rear of
shelf to be contoured to fit over and slide along curbing of
conveyor and provided with positive locking clip to engage
lower edge of conveyor bed.
Stationay Conveyor
ROUGH-IN LOCATION
WITH NO WIREWAY
ROUGH-IN LOCATION
WITH A WIREWAY
Sketches shown are for general layout purposes only,
subject to changes without prior notice consistent with latest
design changes. For final dimensional and roughing data,
special drawings applicable to a specific order should be
requested from Caddy Engineering Department.
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-2 SERIES
to be driven only on top surface of conveyor bed. No drain
pans. All bearings to be heavy duty ball-type, with sealed
lubrication.
Conveyor bed to be 14 gauge stainless steel of
welded construction, ground and polished. Conveyor bed
height to be 42 1/2" and to elevated over support equipment.
Structural Supports to be stainless steel and welded to
underside of conveyor bed. Conveyor to be provided with a
screwed in place access panel at tail end providing access
to bearings.
Drive housing to consist of 18 gauge stainless steel
enclosure on two sides with removable 18 gauge panels.
Conveyor belt to direct drive by variable speed motor
FEATURES
x Servies as two conveyors in one without requiring extra with range of belt speed 5 to 40 feet per minute rated for
large floor space. 120/208/60/3 phase, 4 wire plus separate ground.
x Double track powered unit for maximum efficiency in Motor to be controlled manually through an on/off
large institutions. push-button switch and automatically through a limit switch,
x Elevated conveyor bed cuts down on stretching and both located at discharge end. All wired to splashproof SCR
turning to lessen fatigue. controller with low voltage and overload protection. All
SPECIFICATIONS: electrical components above, as well as the motor, to be
completely interwired through waterproof flex conduit and
Series XL-2 EXPRESS LINE Tray make-up conveyor to be splashproof conduit connectors, terminating in waterproof
as manufactured by Caddy Corporation Unit shall be 36 1/4" circuit breaker panel(s).
wide x ________ long, and to accommodate flat bottom Leg assembly of 16 gauge tubular stainless steel 1
trays up to 15" wide. (Specify dimensions of trays to be 5/8" O.D. and 1" O.D. crossbracing completely welded.
used.)
(Continue specifications by selecting stationary or mobile model)
Conveyor belt to consist of dual 1/2" diameter
Dura-San belting. Belting itself is USDA accepted, highly Stationary Unit
resistant to abrasion, dirt, oil and most chemicals, maintains Fitted with adjustable stainless steel bullet feet.
tension without springs, sprockets or links, continuous
Mobile Unit
without ends or mechanical connection devices. Start end to
be provided with 6" long tray rest. discharge end to have 20" Fitted with 5" diameter polyurethane tired casters, two with
long tray pick-up area, with limit switch activated by brakes. Conveyor shall have 6'-0" long power cord.
stainless steel lever protruding through slot in belt bed. Belt
NOMINAL LENGTH
3'-0 1/4"
11 3/4" 2'-0"
1'-3 1/2"
1 3/4" 1 3/4"
3'-6 1/2"
3'-6 1/2"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-2 SERIES
Optional Features: Double Overshelf for Storage of Cookies, Crackers,
Desserts, etc.
Wireway with Factory Installed Electric Outlets
Double overshelf to be Model ACC-6015 and to set on
Caddy-veyor to be furnished with a recessed stainless steel
curbing of conveyor. To be approximately 5'-0" long with two
wireway and electric outlets with hinged moisture proof
shelves 15" wide of 16 gauge stainless steel turned down 1"
covers for adjoining mobile equipment on both sides, all as
on all four sides, supported by splayed legs of 1" O.D. 16
indicated on plan. Outlets wired to one or more circuit
gauge stainless steel tubing with guides at bottom to slide to
breaker panels with each receptacle having its own circuit
any convenient location.
breaker control with manual reset feature and shut-off. All
electrical work to be ready for single final connection by Overhead Starter Shelf
others to a circuit breaker panel at the job site.
Overhead tray starter shelf to be Model T-565 and to set on
Specify number of outlets, as well as voltage, phase,
curbing of conveyor. To be approximately 3'-0" long with
wattage or motor size and location for each electrical plug-in
sloped shelf of 16 gauge stainless steel turned down 1" on
outlet required. Preferred input voltage is 120/208v, 3ph, 5
front and back. Cutout in shelf to accommodate three pans
wire system including ground.
4" deep. Mounted on legs of 1" O.D. 16 gauge stainless
*IMPORTANT NOTE ON ELECTRICAL DATA*
steel tubing with guides at bottom to slide to any convenient
Maximum allowable amperage for mobile tray make-up
location.
conveyor is 100 amps 3 phase. If total amperage exceeds
100 amp, 3 phase, a second circuit breaker panel will be Undermount Starter Shelf
require. A separate electric connection is needed in the field Undermount tray starter shelf to be Model T-566 and to be
for EACH circuit breaker panel on the conveyor. mounted under conveyor bed with two 14 gauge brackets.
To be approximately 3'-0" long with sloped shelf of 16 gauge
Removable Work and Storage Shelf for Advance stainless steel turned down 1" on front and back. Cutout in
Make-Up of Soup and Beverages shelf to accommodate three pans 4" deep.
Work and storage shelf to be Model ACC-2010 made of 16
Stainless Steel Pans
gauge stainless steel flanged up at rear and both sides.
Shelf supported by stainless steel tubular leg with adjustable A set of 3 stainless steel pans (one full, two 1/3 pan) for
stainless steel bullet foot. Shelf size to be 20" X 10". Rear of T-565 or T-566
shelf to be contoured to fit over and slide along curbing of
conveyor and provided with positive locking clip to engage
lower edge of conveyor bed.
Stationay Conveyor
ROUGH-IN LOCATION
WITH NO WIREWAY
ROUGH-IN LOCATION
WITH A WIREWAY
Sketches shown are for general layout purposes only,
subject to changes without prior notice consistent with latest
design changes. For final dimensional and roughing data,
special drawings applicable to a specific order should be
requested from Caddy Engineering Department.
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-1C PRISON PACKAGE
long tray pick-up area, with limit switch activated by
stainless steel lever protruding through slot in belt bed. Belt
to be driven only on top surface of conveyor bed. No drain
pans. All bearings to be heavy duty ball-type, with sealed
lubrication.
Conveyor bed to be 14 gauge stainless steel of
welded construction, ground and polished. Legs to be 16
gauge tubular stainless steel 1 5/8" O.D. with 1" O.D.
crossbracing completely welded. Conveyor bed height to be
42 1/2" and to elevated over support equipment.
Structural supports to be stainless steel and welded
to underside of conveyor bed. Conveyor to be provided with
FEATURES an access panel at tail end providing access to bearings.
x No parts can be removed. Panel to be screwed in place with tamper-proof stainless
x No concealed places to store contraband steel security screws.
x All exposed fasteners are heavy duty stainless steel Drive housing to consist of 18 gauge stainless steel
tamper-proof fasteners. enclosure on two sides with removable 18 gauge panels.
x Elevated designed to accommodate tray assembly Panels to be fastened with tamper-proof stainless steel
support equipment underneath, thereby saving 15-20% security screws. Housing to have 6 1/2" high adjustable
floor space as compared to conventional assembly lines. stainless steel feet. Bottom of housing to have perforated
x Single track powered unit for time-saving tray completion stainless steel panel welded in place. No place to store
in medium to moderately large institutions. contraband will be allowed.
x Elevated conveyor bed cuts down on stretching and
Conveyor belt to direct drive by variable speed motor
turning to lessen fatigue.
with range of belt speed 5 to 40 feet per minute rated for
SPECIFICATIONS: 120/208/60/3 phase, 4 wire plus separate ground.
Series XL-1C PRISON LINE Tray make-up conveyor to be Motor to be controlled manually through an on/off
as manufactured by Caddy Corporation Unit shall be 19" push-button switch and automatically through a limit switch,
wide x ________ long, and to accommodate flat bottom both located at discharge end. All wired to splashproof SCR
trays up to 15" wide. (Specify dimensions of trays to be controller with low voltage and overload protection. All
used.) controls and wiring to be protected from disassembly and
Conveyor belt to consist of dual 1/2" diameter unauthorized adjustments.
Dura-San belting. Belting itself is USDA accepted, highly (Continue specifications by selecting stationary or mobile model)
resistant to abrasion, dirt, oil and most chemicals, maintains Mobile Unit
tension without springs, sprockets or links, continuous
Fitted with 5" diameter polyurethane tired casters, two with
without ends or mechanical connection devices. Start end to
brakes. Conveyor shall have 6'-0" long power cord.
be provided with 6" long tray rest. discharge end to have 20"
NOMINAL LENGTH
1'-6 3/4" 11 3/4" 2'-0"
1'-3 1/2"
1 3/4" 1 3/4"
3'-6 1/2"
3'-6 1/2"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
XL-1C PRISON PACKAGE
Optional Features: Shelf supported by stainless steel tubular leg with adjustable
Wireway with Factory Installed Electric Outlets stainless steel bullet foot. Shelf size to be 20" X 10". Rear of
Caddy-veyor to be furnished with a stainless steel shelf to be contoured to fit over and slide along curbing of
wireway recessed under conveyor bed with removable conveyor and provided with positive locking clip to engage
lower edge of conveyor bed.
screw cover. Wireway will distribute to power risers locate at
each leg assembly. Both sides of power riser to be provided Double Overshelf for Storage of Cookies, Crackers,
with moisture-proof electric outlets with hinged covers for Desserts, etc.
adjoining mobile equipment, all as indicated on plan. Outlets Double overshelf to be Model ACC-6015 and to set on
wired to one or more circuit breaker panels with each curbing of conveyor. To be approximately 5'-0" long with two
receptacle having its own circuit breaker control with manual shelves 15" wide of 16 gauge stainless steel turned down 1"
reset feature and shut-off. All wireway fasteners and on all four sides, supported by splayed legs of 1" O.D. 16
receptacle fasteners to be heavy duty tamper-proof stainless gauge stainless steel tubing with guides at bottom to slide to
steel security type. All electrical work to be ready for single any convenient location.
final connection by others to a circuit breaker panel at the Overhead Starter Shelf
job site.
Overhead tray starter shelf to be Model T-565 and to set on
Specify number of outlets, as well as voltage, phase, curbing of conveyor. To be approximately 3'-0" long with
wattage or motor size and location for each electrical plug-in sloped shelf of 16 gauge stainless steel turned down 1" on
outlet required. Preferred input voltage is 120/208v, 3ph, 5 front and back. Cutout in shelf to accommodate three pans
wire system including ground. 4" deep. Mounted on legs of 1" O.D. 16 gauge stainless
*IMPORTANT NOTE ON ELECTRICAL DATA* steel tubing with guides at bottom to slide to any convenient
If total amperage exceeds 100 amp, 3phase, a second location.
circuit breaker panel may be require. For mobile tray
Undermount Starter Shelf
make-up conveyor the maximum allowable amperage for
each circuit breaker panel with 6'-0" cord and plug is 100 Undermount tray starter shelf to be Model T-566 and to be
amps. A separate electric connection is needed in the field mounted under conveyor bed with two 14 gauge bracket. To
for EACH circuit breaker panel on the conveyor. be approximately 3'-0" long with sloped shelf of 16 gauge
stainless steel turned down 1" on front and back. Cutout in
Removable Work and Storage Shelf for Advance shelf to accommodate three pans 4" deep.
Make-Up of Soup and Beverages
Stainless Steel Pans
Work and storage shelf to be Model ACC-2010 made of 16
gauge stainless steel flanged up at rear and both sides. A set of 3 stainless steel pans (one full, two 1/3 pan) for
T-565 or T-566
Stationay Conveyor
ROUGH-IN LOCATION
WITH NO WIREWAY
ROUGH-IN LOCATION
WITH A WIREWAY
Sketches shown are for general layout purposes only,
subject to changes without prior notice consistent with latest
design changes. For final dimensional and roughing data,
special drawings applicable to a specific order should be
requested from Caddy Engineering Department.
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
R NON-POWERED XL-S LOCATION:
This superior non-powered unit brings a cost cutting tray make-up system to
small hospitals and nursing homes. Affords the most sophisticated method of TRAY
achieving economy and simplicity of operation. Non-mechanized, non STARTER
powered, utilizing the skatewheel principle of tray movement.
MODEL UNDERLINER
XL-S DISPENSER
SKATEWHEEL
recommended for
institutions with HOT FOOD
up to 150 BEDs UNIT
unlimited length as desired
FROST
TOP UNIT
COFFEE
AND MUG
DISPENSER
TRAY
DELIVERY
TRUCK
DOME
COVER MILK AND
DISPENSER TOASTER ICE CREAM
AND STAND DISPENSER
FEATURES polished. Conveyor bed height to be 42 1/2" and to elevated
over support equipment. Both longitudinal curbings for
x Most economical non-mechanized, non-powered
conveyor bed to have channeled edges with 1" turndown
Caddy-veyor. Use only for flat bottom trays. (Not used for
and extending 1 1/2" above the top of the skatewheels.
trays with irregular bottoms).
Structural supports to be stainless steel and welded to
Specification: underside of conveyor bed. Each end of conveyor bed to be
provided with tray stop and hand lift access with bed
Series XL-S Skatewheel tray make-up conveyor to be as cleanout provision.
manufactured by Caddy Corporation. Unit shall be 19 1/4" Leg assembly of 16 gauge tubular stainless steel 1
wide x ________ long, and to accommodate flat bottom 5/8" O.D. and 1" O.D. crossbracing completely welded.
trays up to 16" wide. (Specify dimensions of trays to be (Continue specifications by selecting stationary or mobile model)
used.)
Conveyor bed to have two rows of 1.9" O.D. plastic Stationary Unit
skatewheels with stainless steel ball bearings spaced on Fitted with adjustable stainless steel bullet feet.
approximately 2 1/4" centers and mounted with stainless Mobile Unit
steel hardware. Conveyor to be provided with 16 gauge
Fitted with 5" diameter polyurethane tired casters, two with
stainless steel bed of welded construction, ground and
brakes. Conveyor shall have 6'-0" long power cord.
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
R NON-POWERED XL-S LOCATION:
Double Overshelf for Storage of Cookies, Crackers,
Desserts, etc.
Double overshelf to be Model ACC-6015 and to set on
curbing of conveyor. To be approximately 5'-0" long with two
shelves 15" wide of 16 gauge stainless steel turned down 1"
on all four sides, supported by splayed legs of 1" O.D. 16
gauge stainless steel tubing with guides at bottom to slide to
any convenient location.
Overhead Starter Shelf
MODEL XL-S 1'-7 1/4" Overhead tray starter shelf to be Model T-565 and to set on
curbing of conveyor. To be approximately 3'-0" long with
Optional Features: sloped shelf of 16 gauge stainless steel turned down 1" on
front and back. Cutout in shelf to accommodate three pans
Wireway with Factory Installed Electric Outlets 4" deep. Mounted on legs of 1" O.D. 16 gauge stainless
Caddy-veyor to be furnished with a stainless steel wireway steel tubing with guides at bottom to slide to any convenient
recessed under conveyor bed with removable screw cover. location.
Wireway will distribute to power risers locate at each leg
assembly. Both sides of power riser to be provided with Undermount Starter Shelf
moisture-proof electric outlets with hinged covers for Undermount tray starter shelf to be Model T-566 and to be
adjoining mobile equipment, all as indicated on plan. Outlets mounted under conveyor bed with two 14 gauge brackets.
wired to one or more circuit breaker panels with each To be approximately 3'-0" long with sloped shelf of 16 gauge
receptacle having its own circuit breaker control with manual stainless steel turned down 1" on front and back. Cutout in
reset feature and shut-off. All electrical work to be ready for shelf to accommodate three pans 4" deep.
single final connection by others to a circuit breaker panel at
the job site. Stainless Steel Pans
Specify number of outlets, as well as voltage, phase, A set of 3 stainless steel pans (one full, two 1/3 pan) for
wattage or motor size and location for each electrical plug-in T-565 or T-566
outlet required. Preferred input voltage is 120/208v, 3ph, 5
wire system including ground.
*IMPORTANT NOTE ON ELECTRICAL DATA*
Maximum allowable amperage for mobile tray make-up
conveyor is 100 amps 3 phase. If total amperage exceeds
100 amp, 3 phase, a second circuit breaker panel will be
require. A separate electric connection is needed in the field
for EACH circuit breaker panel on the conveyor.
NOMINAL LENGTH
1'-7 1/4"
1'-4 1/4"
1 1/2" 1 1/2"
3'-6 1/2"
3'-6 1/2" 3'-7 3/4"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 1 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
R NON-POWERED XL-R LOCATION:
receptacle having its own circuit breaker control with manual
reset feature and shut-off. All electrical work to be ready for
single final connection by others to a circuit breaker panel at
the job site.
Specify number of outlets, as well as voltage, phase,
wattage or motor size and location for each electrical plug-in
outlet required. Preferred input voltage is 120/208v, 3ph, 5
wire system including ground.
*IMPORTANT NOTE ON ELECTRICAL DATA*
Maximum allowable amperage for mobile tray make-up
conveyor is 100 amps 3 phase. If total amperage exceeds
100 amp, 3 phase, a second circuit breaker panel will be
MODEL XL-R require. A separate electric connection is needed in the field
FEATURES for EACH circuit breaker panel on the conveyor.
x Heavy duty deluxe tray make-up Roller-veyor, will handle Double Overshelf for Storage of Cookies, Crackers,
any type trays (flat bottom or irregular bottom). Desserts, etc.
Non-mechanized, non-powered. Double overshelf to be Model ACC-6015 and to set on
Specification: curbing of conveyor. to be approximately 5'-0" long with two
shelves 15" wide of 16 gauge stainless steel turned down 1"
Series XL-R Roller tray make-up conveyor to be as on all four sides, supported by splayed legs of 1" O.D. #16
manufactured by Caddy Corporation. Unit shall be 19 1/4" gauge stainless steel tubing with guides at bottom to slide to
wide x ________ long, and to accommodate trays up to 16" any convenient location.
wide. (Specify dimensions of trays to be used.) Overhead Starter Shelf
Conveyor bed to have a single row of full width 1 1/4"
Overhead tray starter shelf to be Model T-565 and to set on
O.D. plastic rollers with stainless steel balls in nylon curbing of conveyor. To be approximately 3'-0" long with
bearings, spaced on approximately 3" centers with stainless sloped shelf of 16 gauge stainless steel turned down 1" on
steel hardware. Conveyor to be provided with 16 gauge front and back. Cutout in shelf to accommodate three pans
stainless steel bed of welded construction, ground and 4" deep. Mounted on legs of 1" O.D. 16 gauge stainless
polished. Conveyor bed height to be 42 1/2" and to elevated steel tubing with guides at bottom to slide to any convenient
over support equipment. Both longitudinal curbings for location.
conveyor bed to have channeled edges with 1" turndown Undermount Starter Shelf
and extending 1 1/2" above the top of the skatewheels. Undermount tray starter shelf to be Model T-566 and to be
Structural supports to be stainless steel and welded to mounted under conveyor bed with two 14 gauge brackets.
underside of conveyor bed. Each end of conveyor bed to be To be approximately 3'-0" long with sloped shelf of 16 gauge
provided with tray stop and hand lift access with bed stainless steel turned down 1" on front and back. Cutout in
cleanout provision. shelf to accommodate three pans 4" deep.
Leg assembly of 16 gauge tubular stainless steel 1 Stainless Steel Pans
5/8" O.D. and 1" O.D. crossbracing completely welded.
A set of 3 stainless steel pans (one full, two 1/3 pan) for
(Continue specifications by selecting stationary or mobile model)
T-565 or T-566
1'-7 1/4"
Stationary Unit
1'-4 1/4"
Fitted with adjustable stainless steel bullet feet.
1 1/2" 1 1/2"
Mobile Unit
Fitted with 5" diameter polyurethane tired casters, two with
brakes. Conveyor shall have 6'-0" long power cord.
Optional Features:
1 1/4" O.D. Spring Loaded Plastic Rollers 3'-6 1/2" 3'-7 3/4"
Provide single row of full width 1 1/4" O.D. plastic rollers with
stainless steel balls in nylon bearings, spaced at
approximately 3" centers with stainless steel spring loaded
hexagon snap-in shafts.
Wireway with Factory Installed Electric Outlets
Caddy-veyor to be furnished with a stainless steel wire way
recessed under conveyor bed with removable screw cover.
Wireway will distribute to power risers locate at each leg
assembly. Both sides of power riser to be provided with CADDY CORPORATION
moisture-proof electric outlets with hinged covers for 509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
adjoining mobile equipment, all as indicated on plan. Outlets Tel: 856-467-4222 Fax: 856-467-5511
wired to one or more circuit breaker panels with each internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
TM-10 SERIES
indicated on plan. Outlets wired to one or more circuit
breaker panels with each receptacle having its own circuit
breaker control with manual reset feature and shut-off. All
electrical work to be ready for single final connection by
others to a circuit breaker panel at the job site.
Specify number of outlets, as well as voltage, phase,
wattage or motor size and location for each electrical plug-in
outlet required. Preferred input voltage is 120/208v, 3ph, 5
wire system including ground.
Fresh Water Beltwasher:
Provide a welded 16 gauge stainless steel beltwasher
Model BWF with top and bottom fan shaped sprays
SPECIFICATIONS: arranged so lukewarm water thoroughly washes all belt
Series TM-10 Tray Make-Up Conveyor to be as surfaces after which belt is wiped continuously. Beltwasher
manufactured by Caddy Corporation, of length as indicated to have hinged drop-down splash proof stainless steel
on plan and for trays up to 17 1/2" wide. Conveyor to be U.L. access door. Washer to be fitted interconnected water
and N.S.F. listed with labels affixed. pressure reducing valve, water pressure gauge, shutoff
Conveyor belt to consist of a stainless steel chain having valve and thermostatically controlled mixing valve with
approximately 3/4" pitch with 10" wide snap-on slats. Slats check valves. Bottom of beltwasher to have 1 1/2" drain with
to have tapered edges on all sides and molded with integral tailpiece and two removable stainless steel perforated scrap
hold-down tabs. Slats of low friction polycarbonate basket. Beltwasher piping to be complete with approved
compound replaceable without the use of special tools and type vacuum breaker and check valve. All piping exposed to
disassembling of belt chain. Slats not to overlap in any view to be chrome plated.
position to provide effective access of cleaning agents to all (for conveyor over 24 feet long, add the following paragraph)
parts of the assembled belt and conveyor bed. Start end to
be provided with 12" long tray rest. Discharge end to have Auxiliary drain to be provided near start end of conveyor
24" long tray pickup area, with limit switch activated by to obtain proper pitch of drain pan.
(for conveyor with a turn, add the following paragraph)
stainless steel lever protruding through slot in belt bed. All
bearings to be heavy duty ball type, with sealed lubrication. Conveyor to be of configuration as shown on plan.
Caddy-veyor bed to be constructed of 14 gauge Curved section to have positive hold-down tracks made of
stainless steel Type 304 with all edges turned down into 2" non-metallic material at least 1/2" thick with built-in solid
wide channels. Top of bed at longitudinal edges to be raised. lubricant for continuous lubrication of conveyor belt.
All joints to be continuously welded, ground and polished. Materials which transmit heat due to high friction and
Between the drive and tail ends, unit to have 3 1/2" wide resistance are not acceptable. Belt capable of movement
stainless steel channel bracing on approximately 5'-0" through a turn of 22" (standard) radius to the center of the
centers. Conveyor to be provided with stainless steel catch conveyor belt. (Other radii available upon request.)
pan running the full length and pitched to beltwasher.
Conveyor to be enclosed on both sides by full length
skirting approximately 12" high consisting of removable 18
gauge stainless steel panels to provide full access.
Drive housing to consist of 18 gauge stainless steel
enclosure on two sides with removable rear panel and
opposite hinged access door with full height pull. Housing to
set on 6 1/2" high adjustable stainless steel feet. Balance of
conveyor to be supported by 1 5/8" O.D. stainless steel legs
with adjustable stainless steel feet and welded 1" O.D.
stainless steel lateral and longitudinal braces. Conveyor to Model with turn should be specified
be chain driven by variable speed motor with range of belt where building limitations or
speed 0 to 40 feet per minute rated for 120/208/60/3 phase, obstacles prohibit the use of a
4 wire plus separate ground. straight conveyor. May be specified
Motor to be controlled manually through an on/off push in L-shaped, U-shaped, serpentine
button switch and automatically through a limit switch, both or practically any shape.Can't go
located at discharge end. All wired to splash proof SCR straight:
controller with low voltage and overload protection. All Specify Model TM-10 with turns
electrical components above, as well as the motor to be
conveniently located in drive enclosure and to be completely
inter wired through waterproof flexible and conduit and
splash proof circuit connectors.
Caddy-veyor to be furnished with a recessed stainless CADDY CORPORATION
steel wireway and electric outlets with hinged moisture proof 509 Sharptown Road P.O. Box 345
covers for adjoining mobile equipment on both sides, all as Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR LOCATION:
R
TM-10 SERIES
(Continue specifications, indicating applicable service)
Timed Belt Washing Cycle
Optional Features: (for clean-up operations.)
Beltwasher to be controlled by automatic timer activated by
Automatic Water Saver Control for a push button switch inside beltwasher housing in such a
Fresh Water Beltwasher manner that the conveyor and beltwasher will operate
Operation of beltwasher to be controlled by solenoid valve without interruption for an adjustable cycle of up to 16
integrally wired to on/off switch of conveyor to provide minutes. After completion of wash cycle the conveyor is
automatic operation of beltwasher while conveyor is running. ready for the next start-up.
A separate on/off switch to be provided to permit operation
of conveyor without beltwasher. Detergent Injector
(Select for maximum sanitation. Recirculating beltwasher
optional feature is recommended with this option.)
Beltwasher with Recirculating Water
(Recommended for reduction of water consumption and / or in
A siphon type detergent injector working in conjunction with
conjunction with detergent injection.) the beltwasher water supply is to be furnished.
Provide a welded 16 gauge stainless steel beltwasher
Model BWR with top and bottom fan shaped sprays Removable Work and Storage Shelf
arranged so lukewarm water thoroughly washes all belt Work and storage shelf to be Model ACC-2010 made of 16
surfaces after which belt is wiped continuously. Beltwasher gauge stainless steel flanged up at rear and both sides.
to have hinged drop-down splash proof stainless steel Shelf is supported by stainless steel tubular leg with an
access door. Washer to be fitted interconnected water adjustable stainless steel bullet foot. Shelf size is 20" x 10".
pressure reducing valve, water pressure gauge, shutoff Rear of shelf to be contoured to fit over and slide along the
valve and thermostatically controlled mixing valve with curbing of the conveyor and provided with a positive locking
check valves. Bottom of beltwasher to have two removable clip to engage the lower edge of the conveyor bed.
stainless steel perforated scrap basket and 1 1/2" drain with
Double Overshelf
tailpiece and removable constant overflow standpipe to
maintain water level. A pump to be provided to recirculate Double overshelf to be Model ACC-6015 and to set on the
water from reservoir through spray nozzles. Recirculating curbing of the conveyor. Two shelves to be 5'-0" long x 15"
system to include a removable filter to facilitate cleaning. wide of 16 gauge stainless steel turned down 1" on all four
Operation of beltwasher is continuous. A separate on/off sides, supported by splayed legs of 1" O.D. 16 gauge
switch to be provided to permit operation of conveyor stainless steel tubing with guides at the bottom to slide to
without beltwasher. All piping exposed to view to be chrome any convenient location.
plated.
A ROUGH-IN SCHEDULE
NOTE: ALL ROUGH-INS TO BE 4"AFF
SYM QTY DESCRIPTION
A 1 1 1/2" I.P.S. WASTE
B 1 1/2" I.P.S. HOT WATER
C 1 1/2" I.P.S. COLD WATER
D 1 ELECTRICAL CONNECTION
B C D PLAN VIEW
1'-10 1/4"
1'-6 1/4"
NOMINAL LENGTH 2" 2"
2'-0" 3'-0"
1'-0"
1'-0"
2'-10"
2'-10"
ELEVATION VIEW END VIEW
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
Choice of Polycarbonate Slatted LOCATION:
R
or Stretchless PVC Belt
Optional Features:
TR-10 belt is low
friction polycarbonate Wireway with Factory Installed Electric Outlets
slatted belt. Provide a recessed stainless steel wireway and electric
outlets with hinged moistureproof covers for adjoining mobile
equipment on both sides. Outlets wired to one or more
circuit breaker panel(s) as determined by application with
each receptacle having its own circuit breaker control with
manual reset feature and shutoff. All electrical work to be
ready for single final connection by others to each circuit
breaker panel at job site.
MODEL TR-10 Specify number of outlets, as well as voltage, phase,
wattage or motor size and location for each electrical plug-in
outlet required. Preferred input voltage is 120/208v, 3ph, 5
PVC belt is stretchless.
wire system including ground.
Replaces obsolete moisture
*IMPORTANT NOTE ON ELECTRICAL DATA*
absorbing and fraying fabric
Maximum allowable amperage for mobile tray make-up
and neoprene belts.
conveyor is 100 amps 3 phase. If total amperage exceeds
PVC belt is FDA approved.
100 amp, 3 phase, a second circuit breaker panel will be
MODEL SM-10 require. A separate electric connection is needed in the field
FEATURES for EACH circuit breaker panel on the conveyor.
x Ideal as banquet or assembly conveyors for tray up to 17" Removable Work and Storage Shelf for Advance
wide. Make-Up of Soup and Beverages
EX.: airlines, school lunchrooms or convention centers. Work and storage shelf to be Model ACC-2010 made of 16
gauge stainless steel flanged up at rear and both sides.
GENERAL SPECIFICATIONS: Shelf supported by stainless steel tubular leg with adjustable
(Select one) stainless steel bullet foot. Shelf size to be 20" X 10". Rear of
Traymaster TR-10 Servmaster SM-10 shelf to be contoured to fit over and slide along curbing of
Tray Make-Up Conveyor shall Tray Make-Up Conveyor conveyor and provided with positive locking clip to engage
have variable speed 10" wide shall have variable speed 10" lower edge of conveyor bed.
self-tracking stainless steel wide X 1/8" thick deep fused Double Overshelf for Storage of Cookies, Crackers,
chain. Chain shall have snap moisture-proof double sided Desserts, etc.
on/off low friction PVC belt with adjustable
Double overshelf to be Model ACC-6015 and to set on
polycarbonate slats take-up device for tracking.
curbing of conveyor. to be approximately 5'-0" long with two
removable without the use of
shelves 15" wide of 16 gauge stainless steel turned down 1"
tools. Slats shall not overlap
on all four sides, supported by splayed legs of 1" O.D. #16
for ease of cleaning and
gauge stainless steel tubing with guides at bottom to slide to
sanitation.
any convenient location.
SPECIFICATIONS:
Unit shall be 20 1/4" wide x 34" high and ________ long,
which includes 12" starter section and 24" tray pickup at
discharge end.
Top of 14 gauge stainless steel (with raised sides
including stainless steel drive housing). Unit shall have 2
removable 18 gauge stainless steel panels and a removable
crumb shelf inside housing.
Drive with 1/4 h.p. washdown-type motor, reduction
gear, on/off switch, limit switch with tripper arm interwired in
a NEMA 4 enclosure. Unit shall be overload protected and
U.L. listed stationary or mobile.
Leg assembly of 16 gauge tubular stainless steel
1 5/8" O.D. and 1" O.D. crossbracing completely welded.
(Continue specifications by selecting stationary or mobile model)
Stationary Unit
Fitted with adjustable stainless steel bullet feet.
Mobile Unit CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Fitted with 5" diameter polyurethane tired casters, two with Bridgeport, NJ 08014-0345
brakes. Conveyor shall have 6'-0" long power cord. Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 2 of 2 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
Choice of Polycarbonate Slatted LOCATION:
R
or Stretchless PVC Belt
MODEL TR-10
MODEL SM-10
1'-8 1/4"
1'-4 1/4"
NOMINAL LENGTH
2" 2"
2'-0" 11"
2'-10" 2'-10"
TR-10 SECTION
TR-10 ELEVATION VIEW
1'-8 1/4"
1'-4 1/4"
NOMINAL LENGTH
2" 2"
2'-0" 9"
2'-10" 2'-10"
SM-10 SECTION
SM-10 ELEVATION VIEW
Sketches shown are for general layout purposes only,
Stationay Conveyor subject to changes without prior notice consistent with latest
ROUGH-IN LOCATION design changes. For final dimensional and roughing data,
WITH NO WIREWAY special drawings applicable to a specific order should be
requested from Caddy Engineering Department.
ROUGH-IN LOCATION
WITH A WIREWAY
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 1 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
LOCATION:
R NON-POWERED / RCF
Optional Features:
1 1/4" O.D. Spring Loaded Plastic Rollers
Provide single row of full width 1 1/4" O.D. plastic rollers with
stainless steel balls in nylon bearings, spaced at
approximately 3" centers with stainless steel spring loaded
hexagon snap-in shafts.
Wireway with Factory Installed Electric Outlets
Provide a recessed stainless steel wireway and electric
outlets with hinged moistureproof covers for adjoining mobile
MODEL RCF equipment on both sides. Outlets wired to one or more
circuit breaker panel(s) as determined by application with
FEATURES each receptacle having its own circuit breaker control with
manual reset feature and shutoff. All electrical work to be
x Heavy duty deluxe tray make-up Roller-veyor, will handle ready for single final connection by others to each circuit
any type trays (flat bottom or irregular bottom). breaker panel at job site.
Non-mechanized, non-powered. Specify number of outlets, as well as voltage, phase,
wattage or motor size and location for each electrical plug-in
Specification: outlet required. Preferred input voltage is 120/208v, 3ph, 5
Series RCF Roller tray make-up conveyor to be as wire system including ground.
manufactured by Caddy Corporation Unit shall be 19 1/4" *IMPORTANT NOTE ON ELECTRICAL DATA*
wide x ________ long, and to accommodate trays up to 16" Maximum allowable amperage for mobile tray make-up
wide. (Specify dimensions of trays to be used.) conveyor is 100 amps 3 phase. If total amperage exceeds
Conveyor bed to have a single row of full width 1 1/4" 100 amp, 3 phase, a second circuit breaker panel will be
O.D. plastic rollers with stainless steel balls in nylon require. A separate electric connection is needed in the field
bearings, spaced on approximately 3" centers with stainless for EACH circuit breaker panel on the conveyor.
steel hardware. Conveyor to be provided with 16 gauge Removable Work and Storage Shelf for Advance
stainless steel bed of welded construction, ground and Make-Up of Soup and Beverages
polished. Conveyor to be 34" high to top of rollers. Both
Work and storage shelf to be Model ACC-2010 made of 16
longitudinal curbings for conveyor bed to have channeled
gauge stainless steel flanged up at rear and both sides.
edges with 1" turndown and extending 1 1/2" above
Shelf supported by stainless steel tubular leg with adjustable
the top of the roller. Structural supports to be stainless steel
stainless steel bullet foot. Shelf size to be 20" X 10". Rear of
and welded to underside of conveyor bed. Each end of
shelf to be contoured to fit over and slide along curbing of
conveyor bed to be provided with tray stop and hand lift
conveyor and provided with positive locking clip to engage
access with bed cleanout provision.
lower edge of conveyor bed.
Leg assembly of 16 gauge tubular stainless steel
1 5/8" O.D. and 1" O.D. crossbracing completely welded. Double Overshelf for Storage of Cookies, Crackers,
Desserts, etc.
(Continue specifications by selecting stationary or mobile model) Double overshelf to be Model ACC-6015 and to set on
curbing of conveyor. to be approximately 5'-0" long with two
Stationary Unit shelves 15" wide of 16 gauge stainless steel turned down 1"
Fitted with adjustable stainless steel bullet feet. on all four sides, supported by splayed legs of 1" O.D. 16
Mobile Unit gauge stainless steel tubing with guides at bottom to slide to
any convenient location.
Fitted with 5" diameter polyurethane tired casters, two with
brakes. Conveyor shall have 6'-0" long power cord.
1'-7 1/4"
1'-4 1/4"
1 1/2" 1 1/2"
2'-10" 2'-11 1/4"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 1 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
LOCATION:
R NON-POWERED / SWF
Optional Features:
Wireway with Factory Installed Electric Outlets
Provide a recessed stainless steel wireway and electric
outlets with hinged moistureproof covers for adjoining mobile
equipment on both sides. Outlets wired to one or more
circuit breaker panel(s) as determined by application with
each receptacle having its own circuit breaker control with
manual reset feature and shutoff. All electrical work to be
ready for single final connection by others to each circuit
breaker panel at job site.
MODEL SWF Specify number of outlets, as well as voltage, phase,
wattage or motor size and location for each electrical plug-in
FEATURES outlet required. Preferred input voltage is 120/208v, 3ph, 5
wire system including ground.
x Most economical non-mechanized, non-powered *IMPORTANT NOTE ON ELECTRICAL DATA*
Caddy-veyor. Use only for flat bottom trays. (Not used for Maximum allowable amperage for mobile tray make-up
trays with irregular bottoms). conveyor is 100 amps 3 phase. If total amperage exceeds
Specification: 100 amp, 3 phase, a second circuit breaker panel will be
require. A separate electric connection is needed in the field
Series SWF Skatewheel tray make-up conveyor to be as for EACH circuit breaker panel on the conveyor.
manufactured by Caddy Corporation. Unit shall be 19 1/4"
wide x ________ long, and to accommodate flat bottom
trays up to 16" wide. (Specify dimensions of trays to be Removable Work and Storage Shelf for Advance
used.) Make-Up of Soup and Beverages
Conveyor bed to have two rows of 1.9" O.D. plastic
Work and storage shelf to be Model ACC-2010 made of 16
skatewheels with stainless steel ball bearings spaced on
gauge stainless steel flanged up at rear and both sides.
approximately 2 1/4" centers and mounted with stainless
Shelf supported by stainless steel tubular leg with adjustable
steel hardware. Conveyor to be provided with 16 gauge
stainless steel bullet foot. Shelf size to be 20" X 10". Rear of
stainless steel bed of welded construction, ground and
shelf to be contoured to fit over and slide along curbing of
polished. Conveyor to be 34" high to top of skatewheels.
conveyor and provided with positive locking clip to engage
Both longitudinal curbings for conveyor bed to have
lower edge of conveyor bed.
channeled edges with 1" turndown and extending 1 1/2"
above the top of the skatewheels. Structural supports to be Double Overshelf for Storage of Cookies, Crackers,
stainless steel and welded to underside of conveyor bed. Desserts, etc.
Each end of conveyor bed to be provided with tray stop and Double overshelf to be Model ACC-6015 and to set on
hand lift access with bed cleanout provision. curbing of conveyor. to be approximately 5'-0" long with two
Leg assembly of 16 gauge tubular stainless steel 1 5/8" shelves 15" wide of 16 gauge stainless steel turned down 1"
O.D. and 1" O.D. crossbracing completely welded. on all four sides, supported by splayed legs of 1" O.D. 16
gauge stainless steel tubing with guides at bottom to slide to
(Continue specifications by selecting stationary or mobile model)
any convenient location.
Stationary Unit
Fitted with adjustable stainless steel bullet feet.
Mobile Unit
Fitted with 5" diameter polyurethane tired casters, two with
brakes. Conveyor shall have 6'-0" long power cord.
1'-7 1/4"
1'-4 1/4"
PRECISION SKATEWHEELS
1 1/2" 1 1/2"
WITH STAINLESS STEEL
BALL BEARINGS ON 2 1/4"
CENTERS
2'-10" 2'-11 1/4"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07ITEM NO:
CADDY Food Service Systems
page 1 of 1 PROJECT:
TRAY MAKE-UP CADDY-VEYOR
CANTILEVERED MOBILE CONVEYOR (RCC/SWC) LOCATION:
TABLE OR HOT FOOD MOUNT CONVEYOR (SKW)
R
MODEL SWC MODEL RCC MODEL SKW
FEATURES
FEATURES x Skatewheel conveyor can turn any table or hot food unit
x Provides maximum flexibility in the positioning of Roller or into an efficient system for assembling trays for upto 150
Skatewheel conveyor during serving time in conjunction beds.
with hot food Caddy. Conveyor can be rolled away and x Most economical non-mechanized, non-powered
stored with not in use. Caddy-veyor. Use only for flat bottom trays. (Not used for
trays with irregular bottoms).
Specification:
Specification:
Cantilevered support structure of all welded stainless
steel construction with all welds ground smooth and Series SKW Skatewheel tray make-up conveyor to be as
polished. Base to be formed of two 12 gauge stainless steel manufactured by Caddy Corporation. Unit shall be 19 1/4"
channels fitted with four heavy duty 4" swivel casters, two wide x ________ long, and to accommodate flat bottom
with brakes. Uprights to be 1 5/8" O.D. stainless steel tubing. trays up to 16" wide. (Specify dimensions of trays to be
Support braces of 12 gauge stainless steel welded to used.)
stainless steel to stainless steel sleeves allowing vertical Conveyor bed to have two rows of 1.9" O.D. plastic
adjustment of conveyor bed from 14 1/2" to 20 1/2" above skatewheels with stainless steel ball bearings spaced on
top deck of hot food Caddy. approximately 2 1/4" centers and mounted with stainless
Conveyor (covered under separate specifications section) to steel hardware. Conveyor to be provided with 16 gauge
be bolted to the two cantilever brackets resulting in unitized stainless steel bed of welded construction, ground and
mobile assembly. Entire assembly to be: polished. Conveyor to be 10 1/2" above hot food unt or
table. Both longitudinal curbings for conveyor bed to have
(Select one)
channeled edges with 1" turndown and extending 1 1/2"
Model SWC Model RCC above the top of the skatewheels. Structural supports to be
Tray make-up conveyor to be Tray make-up conveyor to be 1" x 1/4" stainless steel flat bar with mounting holes and
as manufactured by Caddy as manufactured by Caddy welded to underside of conveyor bed. Each end of conveyor
Corporation. Unit shall be 19 Corporation. Unit shall be 19 bed to be provided with tray stop and hand lift access with
1/4" wide x ________ long, 1/4" wide x ________ long, bed cleanout provision.
and to accommodate flat and to accommodate trays up
bottom trays up to 16" wide. to 16" wide. (Specify 1'-7 1/4"
(Specify dimensions of trays dimensions of trays to be 1'-4 1/4"
to be used.) used.) 1 1/2" 1 1/2"
1'-7 1/4" 1'-2 1/2"
10 1/2"
1'-4 1/4"
1 1/2" 1 1/2"
RCC SWC
ADJUSTABLE
FROM
4'-6 1/2" TO
4'-0 1/2"
CADDY CORPORATION
509 Sharptown Road P.O. Box 345
Bridgeport, NJ 08014-0345
Tel: 856-467-4222 Fax: 856-467-5511
internet: www.caddycorp.com
All specifications subject to change without notice 08/07You can also read
