QUEEN CHARLOTTE PHARMACY UPGRADE - PROJECT ADDRESS: 3209 OCEANVIEW DRIVE, QUEEN CHARLOTTE, BC, CANADA
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
QUEEN CHARLOTTE PHARMACY UPGRADE
PROJECT ADDRESS: 3209 OCEANVIEW DRIVE, QUEEN CHARLOTTE, BC, CANADA
PROJECT TEAM
OWNER: ARCHITECT:
NORTHERN HEALTH AUTHORITY STANTEC Architecture Ltd.
300-299 Victoria Street 1100-111 Dunsmuir Street
Prince George, BC V2L 5B8 Vancouver, BC, V6B 6A3
Contact: Contact:
Jay Dupras Eleonore Leclerc
tel: (250) 617-3805 tel: (604) 369-6753
email: Jay.Dupras@northernhealth.ca email: Eleonore.Leclerc@stantec.com
MECHANICAL/PLUMBING
ENGINEER: ELECTRICAL ENGINEER:
STANTEC Consulting Ltd. STANTEC Consulting Ltd.
1100-111 Dunsmuir Street 1100-111 Dunsmuir Street
Vancouver, BC, V6B 6A3 Vancouver, BC, V6B 6A3
Contact: Contact:
John Maccarrone Thys Fourie
APPROXIMATE
LOCATION OF
tel: (778) 772-6936 tel: (778) 838-0194
PHARMACY
RENOVATION
email: john.maccarrone@stantec.com email: thys.fourie@stantec.com
DRAWING LIST:
MAIN
ARCHITECTURAL MECHANICAL
ENTRANCE
A001 - COVER SHEET M001 - DRAWING LIST, LEGEND,
LEGEND, SCHEDULES,
SCHEDULES AND HVACHVACCONTROLS
CONTROLS
A002 - GENERAL NOTES, SYMBOLS M101 - STORES
LEVEL 1 -ROOM UPGRADE - LEVEL 1 - MECHANICAL
MECHANICAL
A101 - FLOOR PLAN - DEMOLITION/PROPOSED M102 - STORES
LEVEL 2/3ROOM UPGRADE--NEW
- MECHANICAL LEVEL 1 - MECHANICAL
WORK
A102 - RCP - DEMOLITION/PROPOSED M201 - NAPRA
M200 UPGRADE - LEVEL
HVAC SCHEDULES 1 - MECHANICAL
AND DETAILS
M202 - NAPRA UPGRADE - LEVEL 2/3 - MECHANICAL - NEW WORK
ELECTRICAL M203 - NAPRA UPGRADE - HVAC SCHEDULES AND DETAILS
E000 - COVER PAGE
E100 - ELECTRICAL RENOVATION
OCEANVIEW DRIVE
E200 - ELECTRICAL SPECIFICATIONS
115602082
SITE PLAN - NTS ISSUED FOR TENDER - MAY 3RD 2021G F E D C B A
SYMBOLS LEGEND ABBREVIATIONS
DETAIL NUMBER AFF ABOVE FINISHED FLOOR OSCI OWNER SUPPLIED CONTRACTOR INSTALLED
100A DOOR OPENING NUMBER CLR CLEAR OSOI OWNER SUPPLIED OWNER INSTALLED
1 SIM
0 1 2 3 4 5 6 CIF CONFIRM IN FIELD OSVI OWNER SUPPLIED, VENDER INSTALLED
A802 CLF CLEAR GLASS +FILM PB PANIC BUTTON Stantec Architecture Ltd.
1 GENERAL SHEET NOTE CPT CARPET PE PATCH EXISTING 1100-111 Dunsmuir Street
SHEET ON WHICH Vancouver, V6B 6A3
DETAIL IS SHOWN CMU CONCRETE MASONRY UNIT PT PAINT
Tel: (604) 696-8000 / Fax: (604) 696-8100
1 DEMOLITION SHEET NOTE CONC CONCRETE PL (PLAM) PLASTIC LAMINATE
5 A A1 ELEVATION NUMBER CSCI CONTRACTOR SUPPLIED CONTRACTOR INSTALLED PREFIN PREFINISHED www.stantec.com
A101 SHEET ON WHICH C/W COMPLETE WITH PS PRESSED STEEL
Copyright Reserved
1 DRAWING REVISION
ELEVATION IS SHOWN CT CERAMIC TILE PTR PRESSURE TREATED The Contractor shall verify and be responsible for all dimensions.
1 DBL DOUBLE PLY PLYWOOD DO NOT scale the drawing - any errors or omissions shall be
ELEVATION NUMBER FLOOR FINISH
B DP DEEP RB RUBBER BASE reported to Stantec without delay.
The Copyrights to all designs and drawings are the property of
4 A600 2 FSV-# DTL DETAIL RCP REFLECTED CEILING PLAN Stantec. Reproduction or use for any purpose other than that
LOCATION OF authorized by Stantec is forbidden.
PHARMACY SHEET ON WHICH BSV-# DS DOWN SPOUT RF RESILIENT FLOORING
RENOVATIONS 3 ELEVATION IS SHOWN
BASE FINISH EXIST (EX) EXISTING RRM RAISED RUBBER MAT
C SIM SIM
SECTION NUMBER
PHOTO TAG
EXP
FF
EXPOSED
FACTORY FINISH
RWL
SCW
RAIN WATER LEADER
SOLID CORE WOOD
1 1
A909 A909
BUILDING SECTIONS #
Axxx
PHOTO NUMBER FG FIBERGLASS SC SEALED CONCRETE
SHEET NUMBER FOS FACE OF SILL SDT SMOKE DETECTOR
SHEET ON WHICH
D
FOC FACE OF CONCRETE SIM SIMILAR
SECTION IS SHOWN ROOM TAG
ROOM NAME G GLASS SS STAINLESS STEEL
ROOM NAME
101 GWB GYPSUM WALL BOARD TFF TOP OF FINISHED FLOOR
ROOM NUMBER
150M2 HL HOLLOW METAL T/O TOP OF
ROOM AREA
E SECTION NUMBER HS HANDICAP SHOWER TYP TYPICAL
SIM
1 HSS HOLLOW STEEL SECTION UNF UNFINISHED
A909
WALL SECTIONS EWD-10F-1 WINDOW TAG
LPO LAST PERSON OUT U.N.O. UNLESS NOTED OTHERWISE
LT LIGHT U/S UNDERSIDE
SHEET ON WHICH WALL TAG
SECTION IS SHOWN MT METAL V.I.F VERIFY IN FIELD
# WALL TYPE
NIC NOT IN CONTRACT VSVI VENDER SUPPLIED VENDER INSTALLED
x WALL TERMINATION
OC ON CENTRE VSCI VENDER SUPPLIED CONTRACTOR INSTALLED
4 FLOOR FLOOR OR ROOF LEVEL NAME
O.I.C OPTICAL IMAGING CAMERA WD WOOD
0'-0" VERTICAL ELEVATION
- WALL FINISH TAG OSF OUTSIDE FACE OF WP WATERPROOFING PHARMACY
RENOVATION
CEILING TYPE BL-# INTERIOR WINDOW COVERING TAG
ACT1 3000
LOCATION PLAN - LEVEL 1 CC-# CUBICLE CURTAIN TAG
CEILING HEIGHT
SC-# SHOWER CURTAIN TAG
Clear Dim. Panel Widths & Types Frame Opening
Door Rm. No. of Room Schedule
Room Name Panel Panel Fire
No. No. Width Height Panels Material Finish Thickness Hardware Type Material Finish Note Area Name Number
Width Type Label
Level 01 7.26 m² ANTE ROOM 1-926
New door, frame and hardware. Stantec Architecture Inc
D926 ANTEROOM 1‐926 915 2150 1 915 D1 ED DP 45 Set 1.0 F1 PS PTD N/A 6.59 m² HAZARDOUS COMPOUNDING ROOM 1-927
Interlocked with door D927 23.16 m² STORE 1-925
50 VARIES 50 SEE SCHEDULE
SEE SCHDL
150 150
GENERAL DEMOLITION NOTES
50
200
3 1. AS REQUIRED BY ALL RENOVATION WORK, REMOVE AND DISPOSE OF PORTIONS OF EXISTING MASONRY, GYMSPUN BOARD WALLS AND CEILINGS
INCLUDING ALL WALL MOUNTED ITEMS, WALL MOUNTED EQUIPMENT AND ACCESSORIES ETC. THE CONTRACTOR SHALL BE FULLY RESPONSIBLE TO
CHECK AND ENSURE THE STRUCTURAL INTEGRITY AND STABILITY OF THE RETAINED PORTIONS OF THE EXISTING WALLS AND STRUCTURAL
ELEMENTS INCLUDING COLUMNS AND FLOOR ASSEMBLY, AND SHALL NOT DEMOLISH ANY STRUCTURAL ELEMENTS IF FOUND EMBEDDED IN THE
EXISTING WALLS OR FLOORS.
LAMINATED
VARIES SEE SCHEDULE
VARIES SEE SCHEDULE
GLAZING 2. REMOVE AND DISPOSE OF EXISTING WALL/PARTITION AS REQUIRED TO CREATE AN OPENING FOR NEW MECHANICAL OPENINGS
50 16 3. AS INDICATED ON FLOOR PLAN REMOVE AND DISPOSE OF EXISTING FLOOR FINISH TO EXISTING CONCRETE SLAB. SCARIFY OR SHOT BLAST AS
REQUIRED TO PREPARE FLOOR FOR UNDERLAYMENT AND/OR FINISH PER MANUFACTURERS.
4. DISPOSAL OF ITEMS SHALL BE IN COORDINATION WITH FACILITIES MANAGEMENT DEPARTMENT / EMPLOYER'S REPRESENTATIVE AND CAN
13
INCLUDE SALVAGING CERTAIN MATERIALS AND DEPOSITING THEM ON CAMPUS OR OFF-SITE. CONTRACTOR TO PREPARE A LIST OF ITEMS TO
BE SALVAGED IN AGREEMENT PRIOR TO START OF DEMOLITION WORK.
50
5. REFER ALSO TO THE MECHANICAL AND ELECTRICAL DRAWINGS PRIOR TO DEMOLITION. THE SCOPE OF WORK HAS GENERALLY BEEN INDICATED ON
1 ISSUED FOR TENDER RLB EL 2021-05-03
1000
THE DRAWINGS FOR THE CONTRACTORS INFORMATION. THE CONTRACTOR SHALL BE RESPONSIBLE TO DETERMINE THE FULL SCOPE, EXTENT,
NATURE AND MANNER OF DEMOLITION REQUIRED TO COMPLETE THE WORK UNDER THIS PACKAGE.
Revision By Appd YYYY.MM.DD
50
6. ONLY WORKMEN SKILLED AND KNOWLEDGEABLE IN THEIR RESPECTIVE TRADES SHALL BE EMPLOYED IN THE DEMOLITION.
7. FACILITY TO REMAIN OPEN AND ACCESSIBLE TO STAFF DURING THE COURSE OF DEMOLITION AND CONSTRUCTION. PROVIDE TEMPORARY
13
LOCATION OF HOARDING/TARPS, FULLY TAPED AND SEALED TO CONTAIN DUST AND DEBRIS. COORDINATE WITH OWNER/FACILITIES MANAGEMENT.
PHARMACY A
RENOVATIONS F1 D1 8. ALL EXISTING FIRE EXIT DOORS ARE TO REMAIN FUNCTIONAL AND ACCESSIBLE FOR EMERGENCY EGRESS. PROVIDE AND MAINTAIN DUST SEALS
AROUND DOORWAYS TO PREVENT DUST FROM ENTERING STAIRS OR OTHER OCCUPIED SPACES.
9. EXISTING AREAS, SURFACES, AND FINISHES NOT AFFECTED BY THE WORK INTHIS CONTRACT SHALL BE PROTECTED PRIOR TO COMMENCEMENT
FRAME TYPE DOOR TYPE FRAME PROFILE AND UNTIL COMPLETION OF THE WORK.
ISSUED FOR 90% CLIENT REVIEW HB EL 2021.01.15
1 : 25 1 : 25 1:5 10. CONTRACTOR TO TAKE CARE TO DEMOLISH ONLY EXISTING CONSTRUCTION WHICH IS REQUIRED TO BE DEMOLISHED AND NOT DISTURB EXISTING
CONSTRUCTION TO REMAIN. IN THE COURSE OF DEMOLITION, IF THE CONTRACTOR DISTURBS EXISTING CONSTRUCTION TO REMAIN, REPAIRS OR Issued By Appd YYYY.MM.DD
B REPLACEMENT SHALL BE COMPLETED AT THE CONTRACTOR'S EXPENSE.
2 11. WHERE DEMOLITION OF EXISTING CONSTRUCTION AND/OR EQUIPMENT OCCURS, PATCH AND REPAIR FLOOR, WALL, AND CEILING CONSTRUCTION
AND/OR FINISHES TO MATCH ADJACENT EXISTING CONSTRUCTION.
MINIMUM DIMENSION FROM EDGE SEE ARCH, MECH, OR ELECTRICAL 12. IF UNFORSEEN CONDITIONS OR EXISTING UNDOCUMENTED UTILITIES OR STRUCTURAL ELEMENTS ARE DISCOVERED, WORK IN THE IMMEDIATE
OF EQUIPMENT TO EDGE OF
HOUSEKEEPING PAD FOR VIBRATION
DRAWINGS FOR SIZE AND LOCATION AREA IS TO BE STOPPED UNTIL THE STATUS OF THE EXISTING UTILITIES / STRUCTURAL ELEMENTS ARE ESTABLISHED BY THE OWNER OR ENGINEER.
OBTAIN APPROVAL TO PROCEED FROM THE OWNER. PRELIMINARY
ISOLATION REQUIREMENT
15M @ 400 E.W. 13. CONTRACTOR MUST NOTIFY THE OWNER THREE DAYS PRIOR TO STARTING A DEMOLITION PHASE SO THE OWNER MAY REMOVE ITEMS, IF NEEDED.
NOT FOR CONSTRUCTION
14. REMOVE AND DISPOSE OF ITEMS OR DEBRIS THAT IS NOT TO BE TURNED OVER TO THE OWNER. COORDINATE WITH THE FACILITIES
15M@400 (1' - 4") H1E DRILL AND DOWEL
MANAGEMENT DEPARTMENT TO ESTABLISH A LOCATION FOR STORAGE OF SALVAGED ITEMS OR EQUIPMENT TO BE TURNED OVER TO THE OWNER.
Not for permits, pricing or other official purposes.
MAIN 25mm (1") CHAMFER
30
TO SLAB WITH HILTI HY200 This document has not been completed or checked and
ENTRANCE TYP. 100 (4") MIN EMBED
/ EXIT is for general information or comment only.
GENERAL CONSTRUCTION NOTES
150 (6")
MAX.
1. GENERAL CONTRACTOR TO CO-ORDINATE ALL SECTIONS OF WORK, PAY ALL FEES AND OBTAIN ALL PERMITS AS REQUIRED.
2. ANY WORK REQUIRED BY THE DRAWINGS OR REASONABLY NECESSARY TO COMPLETE THE WORKSHALL BE THE RESPONSIBILITY OF
THE CONTRACTOR. Queen Charlotte Pharmacy
3. ALL WORK COMPLETED BY THE CONTRACTOR TO BE IN ACCORDANCE WITH THE DRAWINGS. ALTERNATIVES CAN BE PROPOSED BY
PARTIAL FIRE SEPARATIONS PLAN LEVEL 1 - NTS THE CONTRACTOR FOR NORTHERN AUTHORITY REPRESENTATIVES/ DESIGNER APPROVAL PROVIDED THE APPROVED PROJECT
SCHEDULE IS NOT DELAYED AS A RESULT OF SUBSTITUTION AND THE QUALITY IS NOT TO A LESSER STANDARD. QUEEN CHARLOTTE PHARMACY UPGRADE
ANCHOR BOLTS AS REQUIRED 2-ADDITIONAL 15M DOWELS @200 (8") SLAB-ON-GRADE OR SUSPENDED SLAB
BY EQUIPMENT SUPPLIER IF B>2000 (6' - 7"). EMBEDDED 125 (5") 4. ALL WORK TO BE PERFORMED IN ACCORDANCE WITH LATEST APPLICABLE BUILDING CODES AND FIRE REGULATIONS AND ANY
LOCAL BUILDING REQUIREMENTS.
EMBEDDED 125 (5") IN EXISTING SLAB IN EXISTING SLAB
Title
5. VERIFY AND CONFIRM ALL DIMENSIONS ON SITE AND REPORT ANY DISCREPANCIES TO THE ARCHITECT BEFORE PROCEEDING WITH
WORK.
GENERAL NOTES
1 NOTES: 6. THESE DRAWINGS TO BE READ IN CONJUNCTION WITH ALL OTHER DRAWINGS, SCHEDULES, SPECIFICATIONS, DETAILS AND
1. PAD SIZE SHALL BE MINIMUM INDICATED OR AS SHOWN ON THE PLANS OR AS DETERMINED BY THE EQUIPMENT MANUFACTURER AND APPROVED BY THE ENGINEER. ENGINEERING DRAWINGS AND SPECIFICATIONS FOR COORDINATION WHERE APPLICABLE.
2. THE SIZE, NUMBER, TYPE, LOCATION, AND THREAD PROJECTION OF THE ANCHOR BOLTS SHALL BE DETERMINED BY THE EQUIPMENT MANUFACTURER, AND SHALL BE AS
APPROVED BY THE ENGINEER. ANCHOR BOLTS SHALL BE HELD IN POSITION WITH A TEMPLATE WHILE PAD IS BEING PLACED. Project No.
3. EQUIPMENT BASES SHALL BE INSTALLED LEVEL UNLESS SPECIFIED OTHERWISE.
Scale
4. WEDGES OR SHIMS SHALL BE USED TO SUPPORT THE BASE WHILE THE NON-SHRINK GROUT IS PLACED. TEMPORARY LEVELING NUTS SHALL BE BACKED OFF. IF LEFT IN, 115602082 As indicated
HE WEDGES OR SHIMS SHALL NOT BE EXPOSED TO VIEW.
5. USE HILTI HIT HY 200 SYSTEM FOR ALL REBAR AND ANCHOR BOLTS FASTENING TO EXISTING CONCRETE SLAB Revision Drawing No.
1
3/5/2021 7:25:55 PM
TYPICAL HOUSEKEEPING PAD
1 : 10 A-002
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
2 3
8800
REMOVE REFRIGERATOR Stantec Architecture Ltd.
EXISTING COUNTERS AND SET ASIDE FOR
1100-111 Dunsmuir Street
TO REMAIN IN PLACE RELOCATION
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
www.stantec.com
5 TS
EXIST. GLOVE
BOX TO REMAIN Copyright Reserved
EXIST. TALL
The Contractor shall verify and be responsible for all dimensions.
SHELVES
EXISTING PASS-THROUGH DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
TO REMAIN IN PLACE The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
authorized by Stantec is forbidden.
4
3 A-101
A-101
EXIST. STRIP OF FLOORING TO
RESILIENT BE REMOVED (3" W)
FLOORING
REMOVE DOOR, FRAME STORE
2965
AND HARDWARE 1-925
REMOVE STRIP OF EXIST.
SHEET VINYL TO SUIT
NEW DEMARCATION LINE
TS AS SHOWN BELOW
HAZARDOUS COMPOUNDING
ANTE ROOM
ROOM
1-926
EXISTING BSC 1-927
TS TS
EXIST. EXIST. SINK
EXIST. EYEWASH
HOOKS
4
PHARMACY
2450 RENOVATION
1 FLOOR PLAN - DEMOLITION
A-101 1 : 25
EXISTING PASS THROUGH
Stantec Architecture Inc
TS
EXIST. GLOVE
BOX
RAISE EXIST. SS COUNTER TO EXIST. TALL
SUIT RELOCATED FRIDGE EXIST COUNTER SHELVES
RELOCATE EXISTING UNDER
COUNTER REFRIGERATOR DIRTY ZONE
3 EXIST. 4 PATCH AND REPAIR EXIST. WALL
3 DOOR A-101 PROTECTION AFFECTED BY
A-101 DOOR HARDWARE REMOVAL.
NEW CONTRASTING COLOUR STORE
STRIP OF FLOORING TO BE EXIST. DOOR, FRAME AND 1-925
HOT WELDED TO EXISTING HARDWARE RELOCATED.
VINYL FLOOR D926 REFER TO EXIST.
MOUNTING HEIGHTS.
TS CLEAN ZONE
HAZARDOUS COMPOUNDING
ANTE ROOM
EXISTING BSC ROOM TS TS
1-926 1 ISSUED FOR TENDER RLB EL 2021-05-03
1-927
Revision By Appd YYYY.MM.DD
EXIST. EXIST. SINK
EXIST. EYEWASH
HOOKS
ISSUED FOR 90% CLIENT REVIEW HB EL 2021.01.15
Issued By Appd YYYY.MM.DD
2 FLOOR PLAN - PROPOSED
2 A-101 1 : 25
1536 914
PRELIMINARY
NOT FOR CONSTRUCTION
Not for permits, pricing or other official purposes.
515
This document has not been completed or checked and
is for general information or comment only.
350
EXISTING EXISTING
GLOVE BOX TALL
SHELVES
RAISE EXISTING COUNTER TO
SUIT RELOCATED FRIDGE.
DIMS TO BE CONFIRNED.
Queen Charlotte Pharmacy
530
RELOCATE EXISTING
FRIDGE
2185
QUEEN CHARLOTTE PHARMACY UPGRADE
Title
1100
FLOOR PLANS - DEMO AND PROPOSED
TBD
900
900
EXISTING EXISTING
1 WALL BASE WALL BASE
FINISHED FLOOR FINISHED FLOOR
Project No. Scale
115602082 1 : 25
2220 Revision Drawing No.
1
3/5/2021 7:25:57 PM
3
A-101
LEVEL 1 - RM 1-927 CHEMO - NORTH
1 : 25
4
A-101
LEVEL 1 - RM 1-926 ANTE ROOM - NORTH
1 : 25 A-101
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
1 2 3 Stantec Architecture Ltd.
3683 8800
1100-111 Dunsmuir Street
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
PAINT ENTIRETY OF CEILING www.stantec.com
5 IN ROOMS 1-926 & 1-927
Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
HAZARDOUS COMPOUNDING authorized by Stantec is forbidden.
ANTE ROOM
ROOM
1-926
1-927
EXISTING CEILING TO REMAIN EXISTING CEILING TO REMAIN
1213 661
RETAIN EXISTING
LUMINAIRE
NEW RETAIN EXISTING LUMINAIRE
DIFFUSER.
SEE MECH.
603
EXISTING CEILING TO REMAIN IN PLACE CUT EXISTING OPENING TO EXISTING CEILING TO REMAIN IN PLACE
SUIT NEW DIFFUSER.
REFER TO MECH.
1213
RETAIN EXISTING
LUMINAIRE
RETAIN EXISTING LUMINAIRE
4
1139
PHARMACY
GWB 2700 GWB 2700 RENOVATION
603 93
505
Stantec Architecture Inc
REFRAME EXISTING OPENING WITH 92mm GALV STEEL STUD
FRAMING AS REQUIRED. REMOVE ADJACENT GWB AND FRAMING
AS REQUIRED FOR NEW DIFFUSER INSTALLATION, AND PATCH AND
REPAIR WITH MATCHING STEEL STUD FRAMING AND GWB.
TAPE, FEATHER INTO ADJACENT SURFACE, SAND, AND PAINT.
3 1 LEVEL 1 - RCP
A-102 1 : 25
1 ISSUED FOR TENDER RLB EL 2021-05-03
Revision By Appd YYYY.MM.DD
ISSUED FOR 90% CLIENT REVIEW HB EL 2021.01.15
Issued By Appd YYYY.MM.DD
2
PRELIMINARY
NOT FOR CONSTRUCTION
Not for permits, pricing or other official purposes.
This document has not been completed or checked and
is for general information or comment only.
Queen Charlotte Pharmacy
QUEEN CHARLOTTE PHARMACY UPGRADE
Title
CEILING PLAN -
1
DEMOLITION/PROPOSED
Project No. Scale
115602082 1 : 25
Revision Drawing No.
1
3/5/2021 7:25:57 PM
A-102
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
MECHANICAL SHEET LIST AIR FLOW MEASURING STATION (REFER TO CONTROLS LEGEND)
## SHEET NAME
PIPING SYSTEMS (HVAC) VENTILATION (HVAC) QUANTITY
M001 DRAWING LIST, LEGEND, SCHEDULES, AND HVAC - - TYPE
CONTROLS PROJECT
2 1/2" PIPE SIZE AIR FLOW ARROW - SIZE (IN.) AIR OUTLET OR INLET TAG (REFER TO SCHEDULE)
M101 STORES ROOM UPGRADE - LEVEL 1 MECHANICAL NORTH Stantec Consulting Ltd.
CHWR CHILLED WATER RETURN - VOLUME (CFM)
M102 STORES ROOM UPGRADE - LEVEL 1 - MECHANICAL 18"x12" 18"x12" RECTANGULAR DUCT AND SIZE* 1100-111 Dunsmuir Street
M201 NAPRA UPGRADE - LEVEL 1 - MECHANICAL Vancouver, V6B 6A3
NORTH ARROW CHWR(G) CHILLED WATER RETURN - GLYCOL 18"ø 18"ø ROUND DUCT AND SIZE* Tel: (604) 696-8000 / Fax: (604) 696-8100
M202 NAPRA UPGRADE - LEVEL 2/3 - MECHANICAL - NEW
WORK SECTION NUMBER RECTANGULAR DIFFUSER, SUPPLY. OPTIONAL ARROWS SHOW THE
5 CHWR(P) CHILLED WATER RETURN - PROCESS 18"x12"ø 18"x12"ø FLAT OVAL DUCT AND SIZE* FLOW DIRECTION. www.stantec.com
M203 NAPRA UPGRADE - HVAC SCHEDULES AND DETAILS
SIM RECTANGULAR REGISTER OR GRILLE, RETURN
1 CHWS CHILLED WATER SUPPLY 18"x12" EXTERIOR DUCT TREATMENT* Copyright Reserved
_______
WALL SECTIONS
A909 The Contractor shall verify and be responsible for all dimensions.
1 DRAWING REVISION CHWS(G) CHILLED WATER SUPPLY - GLYCOL RECTANGULAR REGISTER OR GRILLE, EXHAUST
18"x12" 18"x12" RECTANGULAR DUCT WITH ACOUSTIC LINING* DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
SHEET ON WHICH CHWS(P) DUCT SECTION, SUPPLY AIR. SIZE* IS HORIZONTAL DIM. x VERTICAL DIM. ROUND DIFFUSER, SUPPLY
CHILLED WATER SUPPLY - PROCESS 30"x12" The Copyrights to all designs and drawings are the property of
SECTION IS SHOWN APPLIES TO RECT., ROUND AND OVAL Stantec. Reproduction or use for any purpose other than that
MATCH LINE CWR CONDENSER WATER RETURN LINEAR DIFFUSER authorized by Stantec is forbidden.
DUCT SECTION, OUTSIDE AIR. APPLIES TO RECT., ROUND AND OVAL
CWR(CT) CONDENSER WATER RETURN (COOLING TOWER) SIDEWALL REGISTER OR GRILLE, SUPPLY
DETAIL NUMBER SECTION NUMBER DUCT SECTION, RETURN AIR. APPLIES TO RECT., ROUND AND OVAL
CWS CONDENSER WATER SUPPLY SIDEWALL GRILLE, RETURN OR EXHAUST
SIM SIM DUCT SECTION, EXHAUST AIR. APPLIES TO RECT., ROUND AND OVAL
1 SIM 1 1
DETAIL CALLOUTS
_______ _______
BUILDING SECTIONS CWS(CT) CONDENSER WATER SUPPLY (COOLING TOWER) UC UNDERCUT DOOR
A802 A909 A909 FLEXIBLE DUCT
DTR DUAL TEMPERATURE RETURN (HOT OR CHILLED) DOOR GRILLE OR LOUVER
ELBOW TURN, SUPPLY DOWN. APPLIES TO RECT., ROUND AND OVAL
SHEET ON WHICH SHEET ON WHICH
DETAIL IS SHOWN SECTION IS SHOWN DTS DUAL TEMPERATURE SUPPLY (HOT OR CHILLED) TRANSFER GRILLE OR LOUVER
ELBOW TURN, OUTSIDE AIR DOWN. APPLIES TO RECT., ROUND AND OVAL
HWR HEATING WATER RETURN COIL (REFER TO CONTROLS LEGEND)
ELBOW TURN, RETURN DOWN. APPLIES TO RECT., ROUND AND OVAL
HWR(G) HEATING WATER RETURN - GLYCOL ELBOW TURN, EXHAUST DOWN. APPLIES TO RECT., ROUND AND OVAL
ID-# EQUIPMENT TAG
GENERAL NOTES HWS HEATING WATER SUPPLY UP CHANGE IN DUCT ELEVATION RISING IN DIRECTION INDICATED QUANTITY
INTENT OF THE DRAWINGS AND SPECIFICATIONS ARE TO PROVIDE COMPLETE PLUMBING, FIRE PROTECTION, HEATING, CONTROL, VENTILATION AND AIR CONDITIONING SYSTEMS FOR THE PROPOSED PROJECT. THE - - TYPE
HWS(G) HEATING WATER SUPPLY - GLYCOL
SYSTEMS PROVIDED SHALL CONFORM TO THE DETAILS STATED IN THE SPECIFICATIONS AND SHOWN ON THE DRAWINGS. ITEMS OR WORK NOT SHOWN OR SPECIFIED, BUT REQUIRED FOR A COMPLETE HEATING, DN CHANGE IN DUCT ELEVATION DROPPING IN DIRECTION INDICATED RADIATION HEATING TAG (REFER TO SCHEDULE)
- LENGTH (FT)
VENTILATION AND AIR CONDITIONING SYSTEM, SHALL BE PROVIDED AND SHALL CONFORM WITH ACCEPTED TRADE PRACTICES, LOCAL CODES, AND GOVERNING AUTHORITIES. PIPE INSULATION - CAPACITY (MBH)
THE DRAWINGS AND SPECIFICATIONS ARE PRESENTED TO DEFINE SPECIFIC SYSTEM REQUIREMENTS AND SERVE TO EXPAND ON THE PRIMARY CONTRACT REQUIREMENTS OF PROVIDING COMPLETE SYSTEMS. THE END CAP
4
DRAWINGS ARE DIAGRAMMATIC AND INDICATE ONLY THE GENERAL ARRANGEMENT OF THE ITEMS COMPRISING THE SEVERAL SYSTEMS INCLUDED IN THE HEATING, VENTILATION AND AIR CONDITIONING WORK.
ELBOW, RECTANGULAR, SMOOTH RADIUS WITH SPLITTER VANES
DO NOT SCALE THE DRAWINGS. BECAUSE OF THE SCALE OF THE DRAWINGS, IT IS NOT POSSIBLE TO INDICATE ALL OFFSETS, FITTINGS, VALVES, OR SIMILAR ITEMS WHICH MAY BE REQUIRED TO MAKE A COMPLETE PIPING COMPONENTS (0.25 R/W DEFAULT) T THERMOSTAT
OPERATING SYSTEM. CAREFULLY INVESTIGATE CONDITIONS AFFECTING WORK AND INSTALL WORK IN SUCH A MANNER THAT INTERFERENCES BETWEEN PIPES, CONDUIT, DUCTS, EQUIPMENT, ARCHITECTURAL AND ELBOW, RECTANGULAR, SMOOTH RADIUS WITHOUT VANES (1.5 R/W H HUMIDITY SENSOR
STRUCTURAL FEATURES SHALL BE AVOIDED. PROVIDE ITEMS THAT MAY BE REQUIRED TO MEET THE CONDITIONS AT THE BUILDING. DEFAULT)
CONTRACTORS SHALL HAVE SUFFICIENT EXPERTISE IN THIS TYPE OF CONSTRUCTION TO REALIZE THE EXTENT OF THE WORK REQUIRED. THEREFORE, IT SHOULD BE OBVIOUS TO ANY PRUDENT FIRM WITH ELBOW, ROUND, SMOOTH RADIUS (1.5 R/W DEFAULT)
EXPERIENCE IN THIS FIELD THAT THESE DOCUMENTS MAY NOT EXPLICITLY DISCLOSE FINAL DETAILS; HOWEVER, CONTRACTORS SHALL HAVE THE EXPERTISE NECESSARY TO INCLUDE NECESSARY APPOINTMENTS. ISOLATION VALVE (GENERIC)
MITERED ELBOW, RECTANGULAR, WITH TURNING VANES
PROTECT FLOORING FROM DAMAGE DURING THE CONSTRUCTION PERIOD. PROVIDE PLYWOOD OR SIMILAR MATERIAL UNDER EQUIPMENT OR MATERIALS STORED ON FLOORS, AND IN AREA WHERE CONSTRUCTION GATE VALVE
MAY DAMAGE THE FLOOR SURFACES. FLOOR SURFACES (INCLUDING SEALER) DAMAGED DURING THE CONSTRUCTION SHALL BE REPLACED AT THE COST OF THE CONTRACTOR AT FAULT. RECTANGULAR TO ROUND TRANSITION
GLOBE VALVE AD
COORDINATE ALL WORK WITH WORK SHOWN ON DRAWINGS FOR OTHER TRADES. COORDINATE EXACT LOCATION OF DIFFUSERS, REGISTERS AND GRILLES WITH ARCHITECTURAL AND ELECTRICAL REFLECTED AD AD DUCT ACCESS DOOR (TOP, SIDE, BOTTOM)
CEILING PLANS.
CHECK VALVE (GENERIC)
FLEXIBLE CONNECTION
PROVIDE MAINTENANCE AREAS AROUND ALL EQUIPMENT AS REQUIRED BY CODES AND RECOMMENDED BY THE EQUIPMENT MANUFACTURER. PAY PARTICULAR ATTENTION TO COIL ACCESS AND REMOVAL. FC
BALANCING VALVE
INDICATED DUCT SIZES ARE CLEAR INSIDE OF DUCT DIMENSIONS, INCLUDING ACOUSTIC DUCT LINER WHERE USED. * NOTE: ALL DUCT SIZES ARE INTERIOR, FREE DIMENSIONS (ALWAYS
PRESSURE REDUCING VALVE WIDTH X HEIGHT IN FLOOR PLAN AND SECTION)
INDICATED DUCT AND PIPING RUNS ARE DIAGRAMMATIC. CONTRACTOR SHALL DETERMINE ALL REQUIRED OFFSETS AND DIRECTION CHANGES BEFORE FABRICATION AND INSTALLATION TO AVOID INTERFERENCE 2-WAY
WITH OTHER TRADES. 2-WAY CONTROL VALVE (GENERIC)
BACKDRAFT DAMPER
3-WAY
3-WAY CONTROL VALVE (GENERIC) BDD
UNLESS OTHERWISE NOTED, ALL DUCTWORK AND PIPING IS OVERHEAD, TIGHT TO UNDERSIDE OF SLAB/STEEL, WITH SPACE FOR INSULATION IF REQUIRED. MANUAL DAMPER
3-WAY
ALL PIPING AND DUCTWORK IN FINISHED ROOMS OR SPACES SHALL BE INSTALLED CONCEALED IN A FURRED CHASE OR ABOVE THE CEILING. PUMP (GENERIC) MOTORIZED DAMPER
M
INSTALL PIPING AND DUCTWORK SO THAT ALL VALVES, DAMPERS AND ACCESS DOORS ARE ACCESSIBLE. Y STRAINER (GENERIC) FIRE DAMPER
NO PIPING OR DUCTWORK SHALL BE LOCATED IN ELECTRICAL ROOMS, ELECTRICAL CLOSETS OR TELECOMMUNICATIONS ROOMS UNLESS THOSE PIPES OR DUCTS SERVE ONLY THAT SPACE AND ARE INDICATED ON PIPE CAP SMOKE DAMPER
3 THE DRAWINGS.
PIPE BREAK SMOKE AND FIRE DAMPER
FLOOR PLANS SHOW GENERAL PIPE ROUTING. REFER TO PIPING DIAGRAMS AND DETAILS FOR LOCATIONS OF VALVES AT EQUIPMENT.
PIPING ELBOW UP DUCT SILENCER
INSTALL ALL DRAIN PIPING WITH 2% MINIMUM GRADE UNLESS OTHERWISE NOTED.
PIPING ELBOW DOWN X CONTROL DEVICE
PROVIDE DRAIN VALVES AT THE BASE OF ALL RISERS AND AT ALL PIPING LOW POINTS ON HOT WATER, GLYCOL WATER AND CHILLED WATER PIPING SYSTEMS. VALVES SHALL BE COMPLETE WITH HOSE
CONNECTIONS AND SCREW-ON CAPS.
UNION CONNECTION 2 3
PROVIDE MANUAL AIR VENTS ON HOT WATER AND CHILLED WATER PIPING BRANCHES AND AT ALL HIGH POINTS FOR VENTING.
PROVIDE SHUT-OFF VALVES AT EQUIPMENT REQUIRING CONNECTION, REGARDLESS OF WHETHER SHOWN ON DRAWINGS.
PROVIDE SHUT-OFF VALVES IN UTILITY SHAFTS ON EACH FLOOR FOR ALL PIPING SERVING THE FLOOR.
DO NOT PROVIDE VALVES IN WATER PRESSURE RELIEF PIPING. Revision By Appd YYYY.MM.DD
PIPING, EXCEPT IN MECHANICAL ROOMS AND ROOMS WITHOUT CEILINGS, SHALL BE LOCATED CONCEALED IN CHASES OR ABOVE THE CEILING UNLESS OTHERWISE NOTED.
UNLESS OTHERWISE NOTED, MINIMUM SIZE FOR ALL PIPING SHALL BE 20mm (3/4"). HAZARDOUS STERILE COMPOUNDING ROOM (Pc - CLEAN HAZARDOUS (HD) STERILE PREP ANTE ROOM (Pb) -NAPRA
ROOM), NAPRA CRITERIA: CRITERIA:
THE MECHANICAL CONTRACTOR SHALL PROVIDE ACCESS PANELS NOT SMALLER THAN 600mmX600mm (24"x24") FOR ACCESS TO CONCEALED TRAPS, VALVES, CLEANOUTS, MOTORS, FIRE DAMPERS, CONTROLS, - ISO CLASS 7 - ISO CLASS 7
DRAIN POINTS, OR SIMILAR ITEMS WHERE NO OTHER MEANS OF ACCESS IS PROVIDED. - 30 AIR CHANGES PER HOUR - 30 AIR CHANGES PER HOUR
- RELATIVE PRESSURIZATION: NEGATIVE: PB-PC > 2.5 Pa - RELATIVE PRESSURIZATION: POSITIVE: PB-PA ≥5 Pa
COORDINATE ALL DUCTWORK PENETRATIONS IN MASONRY WITH STRUCTURAL ENGINEER PRIOR TO ANY WORK BEING PERFORMED. ALL LINTELS REQUIRED TO BE DETAILED BY STRUCTURAL ENGINEER AND - TEMPERATURE ≤ 20oC - TEMPERATURE ≤20oC PHARMACY WORKROOM. REFER TO M100 SERIES DRAWINGS. ISSUED FOR TENDER NG DB 2021.05.03
PROVIDED BY GENERAL CONTRACTOR. PROVIDE SLEEVES FOR ROUND DUCTWORK. - RELATIVE HUMIDITY 40% (RANGE 30 TO 60) - RELATIVE HUMIDITY 40% (RANGE 30 TO 60) ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
- ALL AIR EXHAUSTED TO THE EXTERIOR - ALL AIR EXHAUSTED TO THE EXTERIOR By Appd YYYY.MM.DD
PROVIDE SLEEVES IN STRUCTURE FOR ALL PIPING PENETRATING WALLS OR FLOORS. Issued
E-1
PROVIDE APPROVED FIRESAFING AT OPENINGS IN FLOORS, WALLS, ETC. 200x200
2 TS 25 L-1
LOCATE ALL ROOM THERMOSTATS 1500mm (5'-0") (CENTERLINE) ABOVE FINISHED FLOOR ON THE VERTICAL CENTERLINE OF THE ROOM LIGHT SWITCH. NOTIFY THE ARCHITECT OF ANY ROOMS WHERE THE ABOVE ROOM SCHEDULE 300ø
LOCATION CANNOT BE MAINTAINED OR WHERE THERE IS A QUESTION ON LOCATION. 165
DIFFUSER, REGISTER AND GRILLE SIZES SHOWN ON FLOOR PLANS ARE NECK SIZES OR AS INDICATED BY SCHEDULE. NAPRA - HD Anteroom (Pb) DPS
Pb
PRELIMINARY
1-927 Pa
PAINT ALL PIPING, SUPPORTS, ETC. THAT WILL BE EXPOSED TO WEATHER.
HAZARDOUS
COMPOUNDING
Pc Pb
++ +- NOT FOR CONSTRUCTION
PAINT ALL PIPING, SUPPORTS, ETC. THAT WILL BE EXPOSED IN MECHANICAL ROOMS AND INTERIOR SPACES. NAPRA - HD Sterile ROOM -- ++ 1-925 Not for permits, pricing or other official purposes.
Compounding Room (Pc)
DPS STORE
E-1 TS This document has not been completed or checked and
WHERE SPACE IS AVAILABLE, CONTRACTOR, AT HIS OPTION, MAY SUBSTITUTE RADIUS ELBOWS FOR RECTANGULAR ELBOWS WITH TURNING VANES.
Pharmacy 200x200 TS TS is for general information or comment only.
ARCHITECTURAL, MECHANICAL AND ELECTRICAL ITEMS ARE TO BE SUPPORTED FROM SECONDARY MEMBERS, SUPPLIED AND INSTALLED BY THE CONTRACTOR THAT ARE INDEPENDENT OF THE MAIN STRUCTURAL 25 1-926
MEMBERS. WHERE THE PRIMARY MEMBERS ARE TRUSSES, THE SECONDARY MEMBERS SHOULD BE LOCATED ON THE TOP CHORD NEAR THE INTERSECTION OF THE VERTICAL / DIAGONAL WEB MEMBERS AND THE ANTE ROOM
TOP CHORD, OR ATTACHED TO THE VERTICAL MEMBERS. LOADS LESS THAN 25 KG. MAY BE SUPPORTED FROM THE BOTTOM CHORD, PROVIDED NO MATERIAL IS REMOVED FROM THE BOTTOM CHORD AND THE L-1 E-1
SUPPORT IS LOCATED ADJACENT THE INTERSECTION OF THE VERTICAL /DIAGONAL WEB MEMBERS AND THE BOTTOM CHORD OF THE TRUSSES. 300ø 200x200
200 65
ITEMS ARE NOT TO BE SUPPORTED DIRECTLY FROM THE METAL DECK UNLESS APPROVED BY THE CONSULTANT.
IN AREAS WITH EXPOSED CEILING SPACE, ROUTE DUCTS AS HIGH AS POSSIBLE TO UNDERSIDE OF FLOOR DECK. DUCTS TO BE ROUTED BETWEEN STRUCTURAL MEMBERS WHEN RUNNING PARALLEL, AND RUN THRU
OPEN WEB STEEL JOISTS WHEN RUNNING PERPENDICULAR TO STRUCTURAL MEMBERS. ONLY RUN DUCTS BELOW STRUCTURAL MEMBERS WHEN RUNNING PERPENDICULAR TO SOLID STRUCTURAL MEMBERS SUCH
AS BEAMS, WHERE RUNNING THRU IS NOT AN OPTION. NOTE: THE ANTEROOM AND HAZARDOUS COMPOUNDING
Queen Charlotte Pharmacy
ROOM ARE TO BE PROVIDED WITH NEW LOCAL
PRESSURE/HUMIDITY/TEMPERATURE SENSORS AND
CONTROLS. WALL MOUNTED PRESSURE MONITORS TO BE QUEEN CHARLOTTE PHARMACY UPGRADE
PROVIDED, REFER TO SPECIFICATIONS. INTEGRATE NEW
CONTROLS SEQUENCE INTO EXISTING BMS AND PROVIDE
UPDATE TO GRAPHICS AS REQUIRED. Title
C DRAWING LIST, LEGEND, SCHEDULES,
1 CSA VENTILATION SCHEDULE AND HVAC CONTROLS
Room: CSA Space Space Limit CSA Exhaust Specified CSA Minimum Supply Specified Exhaust Design GE Design WE
Level Number Room: Name Classification Type Volume Area Offset CSA Pressurization Req. Supply Airflow Airflow (L/s) Airflow Airflow Airflow Project No. Scale
LEVEL 1
115602082 As indicated
AHU-2
LEVEL 1 1-926 ANTE ROOM NAPRA - HD Anteroom ISO 7 19.6 m³ 7.3 m² 2700 Pos All Air Exhausted 165 L/s 163 L/s 65 L/s 65 L/s 0 L/s Revision Drawing No.
(Pb) To The Exterior
LEVEL 1 - ENVIRONMENTAL CONTROLS
3/9/2021 1:38:31 PM
LEVEL 1 1-927 HAZARDOUS NAPRA - HD Sterile ISO 7 17.8 m³ 6.6 m² 2700 Neg Pb-Pc = 2.5 Pa All Air Exhausted 200 L/s 148 L/s 250 L/s 250 L/s 0 L/s 1
COMPOUNDING ROOM Compounding Room (Pc) To The Exterior
M001 1 : 50
M001
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
NOTE:
THESE DRAWINGS DO NOT SHOW THE SCOPE FOR THE
NAPRA UPGRADES. REFER TO 200 SERIES DRAWINGS.
Stantec Consulting Ltd.
1100-111 Dunsmuir Street
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
www.stantec.com
5
Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
authorized by Stantec is forbidden.
4
1 STORES ROOM UPGRADE - KEY PLAN 2 STORES ROOM UPGRADE - DEMOLITION
M101 1 : 200 M101 1 : 200
50
3
SEE DETAIL 4 M101
FOR CONTINUATION
SEE DETAIL 3 M101
FOR CONTINUATION
By Appd YYYY.MM.DD
Revision
ISSUED FOR TENDER NG DB 2021.05.03
ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
Issued By Appd YYYY.MM.DD
2
PRELIMINARY
NOT FOR CONSTRUCTION
Not for permits, pricing or other official purposes.
This document has not been completed or checked and
is for general information or comment only.
Queen Charlotte Pharmacy
QUEEN CHARLOTTE PHARMACY UPGRADE
3 STORES ROOM UPGRADE - HVAC - NEW WORK 4 STORES ROOM UPGRADE - HVAC - NEW WORK - CONT'D Title
M101 1 : 200
50 M101 1 : 200
50 STORES ROOM UPGRADE - LEVEL 1
1
MECHANICAL
Project No. Scale
115602082 1AS SHOWN
: 200
Revision Drawing No.
3/9/2021 1:38:32 PM
M101
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
Stantec Consulting Ltd.
1100-111 Dunsmuir Street
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
www.stantec.com
5
Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
authorized by Stantec is forbidden.
TIE INTO NEW CHILLED WATER CONNECTIONS SHOWN
ON NAPRA UPGRADE DWG.
TIE INTO CAPPED CONNECTIONS.
REFER TO M201.
4
NOTE
THIS DRAWING DOES NOT SHOW THE WORK FOR
THE NAPRA UPGRADE. REFER TO M201 FOR
SCOPE. DEPENDING ON WHICH SCOPE IS TO BE
COMPLETED FIRST, PROVIDE 32mm MAIN
CONNECTION AND CAPS FOR EITHER THE NAPRA
UPGRADE OR FOR THIS PROJECT SCOPE.
DRAWING M201 SHOWS THE MAINS AND TIE IN
POINT.
1 STORES ROOM UPGRADE - HYDRONICS - NEW WORK
M102 1 : 200
50
3
By Appd YYYY.MM.DD
Revision
ISSUED FOR TENDER NG DB 2021.05.03
ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
Issued By Appd YYYY.MM.DD
2
PRELIMINARY
NOT FOR CONSTRUCTION
Not for permits, pricing or other official purposes.
This document has not been completed or checked and
is for general information or comment only.
Queen Charlotte Pharmacy
QUEEN CHARLOTTE PHARMACY UPGRADE
Title
STORES ROOM UPGRADE - LEVEL 1 -
1
MECHANICAL
2 STORES ROOM UPGRADE - SCHEDULES
M102 1N.T.S.
: 200 Project No. Scale
115602082 AS SHOWN
1 : 200
Revision Drawing No.
3/9/2021 1:38:32 PM
M102
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
2 3 2 3
Stantec Consulting Ltd.
1100-111 Dunsmuir Street
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
5
B B www.stantec.com
Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
EXACT CONNECTION POINT authorized by Stantec is forbidden.
CAP DUCTWORK FOR TO BE DETERMINED ON SITE.
RECONNECTION
PROVIDE NEW CONTROLLER
EXISTING LAMINAR FLOW EXHAUST DUCT UP
FOR EXISTING AIR VALVE AND
DIFFUSERS IN ANTE ROOM THROUGH EXISTING SHAFT.
INTEGRATE WITH NEW
AND HD COMPOUNDING CONFIRM EXACT ROUTING
PHARMACY CONTROL
ROOM TO BE REMOVED ON SITE.
E-1 SEQUENCE.
200x200
TS 25
200x100 EA(SS) 300ø SA
E-1
200x200
25
L-1
L-1
300ø
300ø
TS 165
200
300ø
TS TS
250ø SA
4 200x100 E-1
200x200
65
200x100 EA(SS)
250ø EA(SS)
CAP DUCT VAV-114B VAV-113C
PERMANENTLY CC-113B
VAV-113B
200ø
200ø 250ø EA(SS)
C C
DUCTWORK COOLING COIL.
PROVIDE DRIP PAN AND DRAIN
TO NEAREST SINK P-TRAP OR TO
HOUSEKEEPING MOP SINK.
ROUTING TO FOLLOW EXISTING
COOLING COIL DRAINAGE.
3
1 LEVEL 1 - DEMOLITION 2 LEVEL 1 - NEW WORK
M201 1 : 50 M201 1 : 50
By Appd YYYY.MM.DD
GENERAL DEMOLITION AND NEW WORK NOTES:
Revision
2 3
1. ALLOW FOR REMOVING AND RELOCATION OF EXISTING SERVICES TO PROVIDE SPACE FOR
NEW SERVICES. ALL DUCTWORK AND PIPING RUNS TO BE COORDINATED WITH SERVICES
ON SITE.
2. MODIFY NEW VAV AND COIL TAG NUMBERS TO CONTINUE FROM EXISTING NUMBERING
SCHEME.
ISSUED FOR TENDER NG DB 2021.05.03
3. OPEN UP CEILING AS REQUIRED TO PERMIT DEMOLITION WORK. NOTE THAT EXISTING
ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
CEILING WITHIN THE PHARMACY ROOMS ARE DRYWALL (1-926 AND 1-927).
Issued By Appd YYYY.MM.DD
4. MAKE GOOD EXISTING CEILINGS AT COMPLETION OF WORK
2 5. COORDINATE ANY REQUIRED SHUTDOWNS WITH OWNER. ASSUME ANY WORK OUTSIDE OF
THE MAIN RENOVATION AREA TO BE COMPLETED AFTER HOURS/OVERNIGHT. COORDINATE
WORK INSIDE THE RENOVATION AREA WITH OWNER.
32 CHWR
6. ALL EQUIPMENT TO BE SEISMICALLY SECURED - REFER TO SPECIFICATIONS.
32 CHWS
PRELIMINARY
TS
7. ALL SERVICE PENETRATIONS THROUGH EXISTING PHARMACY WALLS TO BE
CAULKED/OTHERWISE SEALED TO MAINTAIN PRESSURIZATION OF THE SPACE. FOR
LINE SIZE VALVE AND CAP
FOR FUTURE
NOT FOR CONSTRUCTION
EXISTING SERVICES BEING DEMOLISHED, PENETRATIONS TO BE PATCHED/SEALED. Not for permits, pricing or other official purposes.
CONNECT TO EXISTING
8. AHU S-2 SUPPLY FAN TO BE REBALANCED TO SUIT THE ADDITIONAL 140 L/s REQUIRED FOR 32mm CHILLED WATER LINE. This document has not been completed or checked and
THE ANTEROOM AND HEPA DIFFUSERS. COORDINATE SHUTDOWN is for general information or comment only.
WITH OWNER AND ASSUME
9. LOW LEVEL EXHAUSTS TO BE MOUNTED 300mm AFF. TIE IN TO OCCUR AFTER
HOURS. ASSUME FREEZING
10. EXHAUST DUCTWORK TO BE OF STAINLESS STEEL CONSTRUCTION. TS WILL BE REQUIRED FOR TIE
IN TO MINIMIZE IMPACT TO
TS TS ADJACENT SPACES.
GRILLE, REGISTER, DIFFUSER SCHEDULE NOTE:
CC-113B 20 CHWS / CHWR
20 CHWR
CONNECTIONS FOR STORES Queen Charlotte Pharmacy
NOTES: UPGRADE. REFER TO M201.
1. REFER TO REFLECTED CEILING PLANS EXACT LOCATION. PROVIDE ALL FRAMES AND ACCESSORIES AS REQUIRED FOR PROPER INSTALLATION. 20 CHWS
20mm - 0.063 L/s
2. COLOR TO BE SELECTED BY ARCHITECT FROM STANDARD COLORS.
3. STAINLESS STEEL LAMINAR FLOW NON-ASPIRATING DIFFUSER WITH HEPA FILTER, INLET DIFFUSION BRACKET, STATIC PRESSURE PORT, PRESSURE SWITCH QUEEN CHARLOTTE PHARMACY UPGRADE
C/W BUILDING AUTOMATION SYSTEM INTERFACE FOR FILTER STATUS, BALANCING DAMPER ACCESSIBLE FROM DIFFUSER FACE.
4. PROVIDE S.S. DAMPER FOR LOW LEVEL EXHAUST GRILLES.
5. EXCEPT FOR T-BAR INSTALLATION, GRILLES SHALL BE COMPLETE WITH MOUNTING FRAME TYPE D AND 1/4 TURN QUICK RELEASE FASTENERS. Title
6. STAINLESS STEEL LOUVERED RETURN/EXHAUST GRILLE, 45 DEGREE DEFLECTION, 19MM BLADE SPACING.
NAPRA UPGRADE - LEVEL 1 -
1
MARK
DIFFUSER NECK SIZE
(IN)
MATERIAL MANUFACTURER MODEL NUMBER NOTES MECHANICAL
E-1 200x200 STAINLESS STEEL PRICE 730 RETURN 1,2,4-6
L-1 300ø STAINLESS STEEL PRICE LFDC 1,2,3
Project No. Scale
115602082 1 : 50
Revision Drawing No.
LEVEL 1 - PIPING - NEW WORK
3/9/2021 1:38:35 PM
3
M201 1 : 50
M201
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
3 4
Stantec Consulting Ltd.
3 4 1100-111 Dunsmuir Street
Vancouver, V6B 6A3
Tel: (604) 696-8000 / Fax: (604) 696-8100
www.stantec.com
5
FD Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
B A
3
_______
M202
The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
authorized by Stantec is forbidden.
200mm EXHAUST DUCT UP TO 3M
250ø ABOVE HIGHEST POINT ON ROOF TO
MATCH EXISTING STACKS. TIE INTO
EXISTING SUPPORT STRUCTURE FOR
DUCT. PATCH/SEAL AROUND
OPENING AND MAKE WATER TIGHT
AS REQUIRED. PROVIDE NOZZLE
EXIST TO REACH 3000FPM MINIMUM
(APPROX 100mm EXIT)
EF-PHARM-1
FD NOTE: DUCT RUN IS IN ACTIVE 3
_______
HOSPITAL SPACE. WORK IN M202 ROUND ELBOW SILENCER EF-
250ø EA(SS) CLINICAL AREAS OUTSIDE OF THE
PHARM-1-SIL-1
RENOVATION AREA TO BE
ASSUMED TO OCCUR AFTER NEW EXHAUST FAN ON 100mm
HOURS. COORDINATE WITH HOUSEKEEPING PAD (REFER TO
OWNER. EXACT ROUTING TO BE ARCH FOR HOUSEKEEPING PAD
COORDINATED WITH EXISTING DETAIL).. MOUNT VFD IN LOCATION
4 SERVICES ON SITE. WITH ADEQUATE CLEARANCE (1M).
PROVIDE UNISTRUT FOR
OPEN UP SHAFT TO MOUNTING VSD. CONFIRM EXACT
PERMIT DUCTWORK LOCATION ON SITE.
INSTALLATION.
CONFIRM EXACT RUN PROVIDE OPENINGS AS
LOCATION ON SITE. REQUIRED TO RUN
PROVIDE FIRE DUCTWORK AS SHOWN.
DAMPER AT SHAFT NOTE - THIS DUCTWORK
PROVIDE FIRE DAMPER AT
EXIT. RUN IS IN LEVEL 2
PENETRATION INTO
CEILING (TYP.)
MECHANICAL SPACE. RUN
DUCT WITHIN THE
MECHANICAL SPACE AT HIGH
LEVEL TO MAINTAIN ACCESS
CLEARANCE.
250ø EA(SS)
B
C
3
DUCT UP FROM BELOW
1 LEVEL 2 - NEW WORK
M202 1 : 50 FD
A
By Appd YYYY.MM.DD
Revision
SIZE NOZZLE TO MAINTAIN
3000FPM EXIT VELOCITY PER
ASHRAE (APPROX 100MM)
EXISTING EXHAUSTS IN THIS
AREA. ISSUED FOR TENDER NG DB 2021.05.03
ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
3000
Issued By Appd YYYY.MM.DD
2
C
TOP OF ROOF
15300 PRELIMINARY
PROVIDE WEATHERPROOF NOT FOR CONSTRUCTION
DUCT PENETRATION
THROUGH ROOF. Not for permits, pricing or other official purposes.
S.S. DUCT STACK
This document has not been completed or checked and
is for general information or comment only.
200ø EA(SS)
NEW EXHAUST STACK.
SUPPORT FROM EXISTING
SUPPORT STRUCTURE.
SUPPORT HORIZONTAL
RUNS AS REQUIRED IN
PENTHOUSE
Queen Charlotte Pharmacy
QUEEN CHARLOTTE PHARMACY UPGRADE
PROVIDE LOW POINT DRAIN
AT BOTTOM OF STACK.
ROUTE TO NEAREST DRAIN
TO MATCH OTHER STACKS
Title
ON SITE. NAPRA UPGRADE - LEVEL 2/3 -
1
EF-PHARM-1 NEW EXHAUST FAN ON
2 LEVEL 3 - PENTHOUSE - NEW WORK MECHANICAL - NEW WORK
100mm HOUSEKEEPING PAD. M202 1 : 50
CONFIRM EXACT LOCATION
OF FAN ON SITE.
Project No. Scale
115602082 1 : 50
LEVEL 3 - PENTHOUSE
9000 Revision Drawing No.
3/9/2021 1:38:37 PM
EXHAUST FAN SECTION
3
M202 1 : 50 M202
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
SILENCER SCHEDULE
UNIT IDENTIFICATION AIRFLOW INFORMATION DYNAMIC INSERTION LOSSES DB
OPERATING
DEVICE CONNECTION DIMENSIONS CASING DIMENSIONS MODEL
AIRFLOW VELOCITY WEIGHT MANUFACTURER NOTES
TAG APD CASING GAUGE PERF Media ROUND HEIGHT WIDTH LENGTH 63 125 250 500 1K 2K 4K 8K NUMBER
(L/S) (M/S) (KG)
(PA) (mm) (mm) (mm) (mm) Stantec Consulting Ltd.
EF-PHARM-1-SIL 150 10 3.0 24 GA 304 SS 26 GA 304 SS NONE 250 762 762 2184 (CL) 29 18 43 26 20 19 15 12 - PRICE PECMB86/10 1 1100-111 Dunsmuir Street
Vancouver, V6B 6A3
NOTES: Tel: (604) 696-8000 / Fax: (604) 696-8100
1. ROUND ELBOW SILENCER C/W 2" SLIP, EXTENDED WIDTH CASING
www.stantec.com
5
Copyright Reserved
The Contractor shall verify and be responsible for all dimensions.
FAN SCHEDULE DO NOT scale the drawing - any errors or omissions shall be
reported to Stantec without delay.
UNIT IDENTIFICATION FAN WHEEL FAN MOTOR (EACH FAN) ELECTRICAL The Copyrights to all designs and drawings are the property of
Stantec. Reproduction or use for any purpose other than that
MAX NOISE OPERATING
ESP authorized by Stantec is forbidden.
ASSET AIRFLOW CONTROL SPEED SPEED DRIVE LEVEL WEIGHT MANUFACTURER MODEL NUMBER NOTES
MARK SYSTEM (Pa) TYPE BHP HP VOLTS PHASE
NUMBER (l/s) (RPM) (RPM) TYPE (dBA) (kg)
EF-PHARM-1 HAZARDOUS COMPOUNDING ROOM EXHAUST 150 750 VFD SINGLE WIDTH CENT. BLOWER 3,126 0.67 0.75 3,600 BELT 208 3 73 70 GREENHECK USF-06 ALL
NOTES:
1. NEMA PREMIUM EFFICIENT MOTOR, INVERTER DUTY, TEFC, CLASS B OR GREATER INSULATION, CSA APPROVED, SHAFT GROUNDING, 120K HOUR BEARINGS, FACTORY VIBRATION TESTED, MOTOR COVER.
2. VFD MOUNTED AND WIRED
3. HI-PRO POLYESTER COATING
AIR VALVE SCHEDULE (AV)
COOLING COIL OCCUPIED MODE UNOCCUPIED MODE
AIR VALVE No. ASSET NUMBER MANUFACTURER MODEL SIZE BODY CONST'N COOLING. CAP. MIN. MAX. MIN. NOTES
ROWS FLOW (L/s) MAX. (L/s)
(kW) (L/s) (L/s) (L/s)
ANTEC ALUMINUM/COATED
VAV-114B PRICE 8 100 50 100 50 1,2,5,6
CONTROLS STAINLESS
4
ANTEC ALUMINUM/COATED
VAV-113C PRICE 8 100 65 100 65 1,2,5,6
DUCT CONNECTIONS TO AIR TERMINAL CONTROLS STAINLESS
ANTEC ALUMINUM/COATED
VAV-113B PRICE 10 2 0.064 0.75 150 150 150 150 1,2,3,4,5,6
1 UNITS CONTROLS STAINLESS
M203 N.T.S. E-VAV-114 EXISTING 10 EXISTING 200 200 200 200 1,2,3
NOTES:
1. AIR VALVES TO BE SUPPLIED WITH AIR PRESSURE MONITORS AND COMPONENTS IN DESIGNATED LOCATIONS AS NOTED ON THE PLANS. PRESSURE MONITOR +/- 1%.
2. EACH AIR VALVE TO BE PROVIDED WITH AN ON-BOARD FACTORY INSTALLED CONTROLLER, COMPLETE WITH PROGRAMMING FOR ROOM LEVEL PRESSURE CONTROL (POC).
3. FACTORY CONTROLLERS TO PROVIDE ROOM-LEVEL HUMIDITY AND TEMPERATURE CONTROL.
4. AIR VALVES TO BE SUPPLIED WITH DUCT MOUNTED COOLING COILS, PERFORMANCE AS FOLLOWS: EWT:10C, LWT:16C, EAT: 18/14.6C DB/WB, LAT: 14/12.3C DB/WB
5. AIR VALVES TO BE SUPPLIED WITH ATTENUATORS.
6. PROVIDE LOW PRESSURE MODELS, 0.3" W.G. (75PA)
7. NOTE: MINIMUM AIRFLOWS ARE TO BE USED FOR BALANCING IN CONJUNCTION WITH THE VALUES ON THE DRAWINGS. THE VALVE CAN OPERATE UP TO THE MAXIMUM IF REQUIRED TO MAINTAIN
SPACE PRESSURE DIFFERENTIALS.
3
PIPE OR DUCT
NOTE:
THE DETAILS ON THIS SHEET ARE TO BE USED FOR BOTH THE STORES FLASHING
UPGRADE AND NAPRA UPGRADES PROJECTS AS APPLICABLE
FIBERGLASS BUILDING Revision By Appd YYYY.MM.DD
INSULATION 0.75 PCF DENSITY
ACOUSTICAL SEALANT
2 DUCT MOUNTED COOLING COIL INSTALLATION DETAIL 25 GA. (MIN.) METAL SLEEVE
M203 N.T.S. (ROOF JACK)
ISSUED FOR TENDER NG DB 2021.05.03
ISSUED FOR 90% CLIENT REVIEW NG DB 2021.01.15
Issued By Appd YYYY.MM.DD
SHEET
2
METAL 2 LOAD RATED FASTENER (TYP)
DUCT
PRELIMINARY
NOT FOR CONSTRUCTION
ROOF CONSTRUCTION Not for permits, pricing or other official purposes.
This document has not been completed or checked and
is for general information or comment only.
25mm (TYP.)
1
R=1.5D
SEISMIC
CABLELLING AS Queen Charlotte Pharmacy
REQUIRED CL
NOTES:
QUEEN CHARLOTTE PHARMACY UPGRADE
1. PROVIDE PITCH POCKET CONSTRUCTION, ADDITIONAL FLASHING OR WEATHER CAP AS REQUIRED FOR WATERPROOF CONSTRUCTION.
DO NOT RIGIDLY TIE DUCT OR PIPE TO STRUCTURE IN ANY WAY.
2. SPACE BETWEEN DUCT OR PIPE AND METAL SLEEVE SHALL BE FREE OF ANY FOREIGN MATERIALS. Title
3. DUCT OR PIPE SHALL NOT DIRECTLY CONTACT STRUCTURE. WEDGES SHALL NOT BE USED TO MAINTAIN PIPE IN POSITION. NAPRA UPGRADE - HVAC SCHEDULES
1
4. DUCT OR PIPE MUST BE APPROX. CENTERED ON OPENING. PROVIDE ADDITIONAL CLEARANCE FOR POSITIONAL CHANGE OF DUCT AND DETAILS
DUE TO LOADING OF DUCT OR OPERATION OF SYSTEM.
KEY NOTES: Project No. Scale
5. NEW PIPE TO BE CENTERED BETWEEN STANDING SEAMS ON METAL ROOF.
1 FLEXIBLE DUCT MAXIMUM LENGTH SHALL BE 1'-0". PROVIDE HARD DUCT ELBOW - 115602082 NTS
USE OF FLEX IS ONLY PERMITTED FOR THE FINAL STRAIGHT LENGTH.
Revision Drawing No.
2 MAXIMUM ALLOWABLE SAG SHALL NOT EXCEED d" PER LINEAR FOOT.
3/9/2021 1:38:39 PM
3
M203
VAV TERMINAL UNIT INSTALLATION DETAIL
N.T.S. M203
4 LAMINAR FLOW SUPPLY DIFFUSER
NTS M203
5 TYPICAL WATERPROOFED PIPE-DUCT PENETRATION DETAIL - PITCHED ROOF
NTS M203
ORIGINAL SHEET - ARCH D (24"x36")G F E D C B A
GENERAL NOTES
Stantec
1.
Staniec Consulting ltd.
ALLOW FOR REMG F E D C B A
4 5
Stantec
' "'" Staniec Consulting ltd.
I I�- , II I I L...___JJ
--�
IYou can also read
