ACRYLIC STUDIO - Acrylicos Vallejo
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
English (UK)
English (USA)
Español
ACRYLIC Deutsch
STUDIO
Français
Italiano
Nederlands
Polski
中文
日本
Safety Data Sheets
Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 1: IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE COMPANY/UNDERTAKING
1.1 Product identifier: ACRYLIC STUDIO
1.2 Relevant identified uses of the substance or mixture and uses advised against:
Relevant uses: Paint
Uses advised against: All uses not specified in this section or in section 7.3
1.3 Details of the supplier of the safety data sheet:
ACRYLICOS VALLEJO, S.L.
Pol. Ind. Sant Jordi - C/ Eusebio Millán, 14
08800 Vilanova i La Geltrú - Barcelona - Spain
Phone.: +34938936012 -
Fax: +34938931154
vallejo@acrylicosvallejo.com
www.acrylicosvallejo.com
1.4 Emergency telephone number: +34 938 936 012 (9:00 - 17:00)
SECTION 2: HAZARDS IDENTIFICATION
2.1 Classification of the substance or mixture:
CLP Regulation (EC) nº 1272/2008:
The product is not classified as dangerous according to CLP Regulation (EC) nº 1272/2008.
2.2 Label elements:
CLP Regulation (EC) nº 1272/2008:
None
2.3 Other hazards:
Non-applicable
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1 Substance:
Non-applicable
3.2 Mixture:
Chemical description: Mixture composed of additives, pigments and resins
Components:
In accordance with Annex II of Regulation (EC) nº1907/2006 (point 3), the product contains:
Identification Chemical name/Classification Concentration
CAS: 9036-19-5 2-(2-[4-(1,1,3,3-Tetramethylbutyl)phenoxy]ethoxy)ethanol Self-classified
EC: 618-541-1Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 4: FIRST AID MEASURES (continued)
By eye contact:
Rinse eyes thoroughly with water for at least 15 minutes. If the injured person uses contact lenses, these should be removed
unless they are stuck to the eyes, as this could cause further damage. In all cases, after cleaning, a doctor should be consulted
as quickly as possible with the SDS of the product.
By ingestion/aspiration:
Do not induce vomiting, but if it does happen keep the head down to avoid aspiration. Keep the person affected at rest. Rinse
out the mouth and throat, as they may have been affected during ingestion.
4.2 Most important symptoms and effects, both acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3 Indication of any immediate medical attention and special treatment needed:
Non-applicable
SECTION 5: FIREFIGHTING MEASURES
5.1 Extinguishing media:
Product is non-flammable under normal conditions of storage, manipulation and use. In the case of inflammation as a result of
improper manipulation, storage or use preferably use polyvalent powder extinguishers (ABC powder), in accordance with the
Regulation on fire protection systems. IT IS NOT RECOMMENDED to use tap water as an extinguishing agent.
5.2 Special hazards arising from the substance or mixture:
As a result of combustion or thermal decomposition reactive sub-products are created that can become highly toxic and,
consequently, can present a serious health risk.
5.3 Advice for firefighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and individual respiratory equipment.
Minimum emergency facilities and equipment should be available (fire blankets, portable first aid kit,...) in accordance with
Directive 89/654/EC.
Additional provisions:
Act in accordance with the Internal Emergency Plan and the Information Sheets on actions to take after an accident or other
emergencies. Destroy any source of ignition. In case of fire, refrigerate the storage containers and tanks for products susceptible
to inflammation, explosion or BLEVE as a result of high temperatures. Avoid spillage of the products used to extinguish the fire
into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1 Personal precautions, protective equipment and emergency procedures:
Isolate leaks provided that there is no additional risk for the people performing this task. Personal protection equipment must be
used against potential contact with the spilt product (See section 8). Evacuate the area and keep out those who do not have
protection.
6.2 Environmental precautions:
Avoid spillage into an aqueous medium as it contains substances potentially dangerous for this. Contain the product absorbed in
hermetically sealed containers. In the case of serious spillage into an aqueous medium notify the relevant authority.
6.3 Methods and material for containment and cleaning up:
It is recommended:
Absorb the spillage using sand or inert absorbent and move it to a safe place. Do not absorb in sawdust or other combustible
absorbents. For any concern related to disposal consult section 13.
6.4 Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1 Precautions for safe handling:
A.- Precautions for safe manipulation
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 2/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 7: HANDLING AND STORAGE (continued)
Comply with the current legislation concerning the prevention of industrial risks. Keep containers hermetically sealed. Control
spills and residues, destroying them with safe methods (section 6). Avoid leakages from the container. Maintain order and
cleanliness where dangerous products are used.
B.- Technical recommendations for the prevention of fires and explosions
Product is non-flammable under normal conditions of storage, manipulation and use. It is recommended to transfer at slow
speeds to avoid the generation of electrostatic charges that can affect flammable products. Consult section 10 for information
on conditions and materials that should be avoided.
C.- Technical recommendations to prevent ergonomic and toxicological risks
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.- Technical recommendations to prevent environmental risks
It is recommended to have absorbent material available at close proximity to the product (See subsection 6.3)
7.2 Conditions for safe storage, including any incompatibilities:
A.- Technical measures for storage
Minimum Temp.: 5 ºC
Maximum Temp.: 30 ºC
B.- General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see subsection 10.5
7.3 Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding the uses of this
product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 Control parameters:
Substances whose occupational exposure limits have to be monitored in the work environment
There are no occupational exposure limits for the substances contained in the product
DNEL (Workers):
Non-applicable
DNEL (General population):
Non-applicable
PNEC:
Non-applicable
8.2 Exposure controls:
A.- General security and hygiene measures in the work place
As a preventative measure it is recommended to use basic Personal Protection Equipment, with the corresponding in accordance with Directive 89/686/EC. For more information on Personal Protection Equipment (storage, use,
cleaning, maintenance, class of protection,…) consult the information leaflet provided by the manufacturer. For more
information see subsection 7.1.
All information contained herein is a recommendation which needs some specification from the labour risk prevention services
as it is not known whether the company has additional measures at its disposal.
B.- Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are exceeded.
C.- Specific protection for the hands
Pictogram PPE Labelling CEN Standard Remarks
Replace gloves in case of any sign of damage. For
prolonged periods of exposure to the product for
Protective gloves against
professional users/industrials, we recommend using
minor risks
CE III gloves in line with standards EN 420 and EN
Mandatory hand 374.
protection
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in advance with
total reliability and has therefore to be checked prior to the application
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 3/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTIONAs
8:the product is aCONTROLS/PERSONAL
EXPOSURE mixture of several substances, the resistance
PROTECTION of the glove material can not be calculated in advance with
(continued)
total reliability and has therefore to be checked prior to the application
D.- Ocular and facial protection
Pictogram PPE Labelling CEN Standard Remarks
Clean daily and disinfect periodically according to
Panoramic glasses against EN 166:2001
the manufacturer´s instructions. Use if there is a
splash/projections. EN ISO 4007:2012
risk of splashing.
Mandatory face
protection
E.- Bodily protection
Pictogram PPE Labelling CEN Standard Remarks
Replace before any evidence of deterioration. For
periods of prolonged exposure to the product for
professional/industrial users CE III is
Work clothing
recommended, in accordance with the regulations
in EN ISO 6529:2001, EN ISO 6530:2005, EN ISO
13688:2013, EN 464:1994.
Replace before any evidence of deterioration. For
periods of prolonged exposure to the product for
Anti-slip work shoes EN ISO 20347:2012 professional/industrial users CE III is
recommended, in accordance with the regulations
in EN ISO 20345 y EN 13832-1
F.- Additional emergency measures
Emergency measure Standards Emergency measure Standards
ANSI Z358-1 DIN 12 899
ISO 3864-1:2002 ISO 3864-1:2002
Emergency shower Eyewash stations
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid environmental
spillage of both the product and its container. For additional information see subsection 7.1.D
Volatile organic compounds:
With regard to Directive 2010/75/EU, this product has the following characteristics:
V.O.C. (Supply): 0,03 % weight
V.O.C. density at 20 ºC: 0,3 kg/m³ (0,3 g/L)
Average carbon number: 6,11
Average molecular weight: 115,95 g/mol
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1 Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 20 ºC: Liquid
Appearance: Dense
Colour: Characteristic
Odour: Characteristic
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: 104 ºC
Vapour pressure at 20 ºC: 2335 Pa
Vapour pressure at 50 ºC: 12250 Pa (12 kPa)
Evaporation rate at 20 ºC: Non-applicable *
Product description:
*Not relevant due to the nature of the product, not providing information property of its hazards.
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 4/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Product description:
Density at 20 ºC: 1089 kg/m³
Relative density at 20 ºC: 1,231
Dynamic viscosity at 20 ºC: 15000 - 20000 cP
Kinematic viscosity at 20 ºC: Non-applicable *
Kinematic viscosity at 40 ºC: Non-applicable *
Concentration: Non-applicable *
pH: 8-9
Vapour density at 20 ºC: Non-applicable *
Partition coefficient n-octanol/water 20 ºC: Non-applicable *
Solubility in water at 20 ºC: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Flammability:
Flash Point: Non Flammable (>60 ºC)
Flammability (solid, gas): Non-applicable *
Autoignition temperature: 379 ºC
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
9.2 Other information:
Surface tension at 20 ºC: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1 Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See section 7.
10.2 Chemical stability:
Chemically stable under the conditions of storage, handling and use.
10.3 Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not expected.
10.4 Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5 Incompatible materials:
Acids Water Combustive materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable Not applicable
10.6 Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the decomposition conditions,
complex mixtures of chemical substances can be released: carbon dioxide (CO2), carbon monoxide and other organic
compounds.
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 5/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 11: TOXICOLOGICAL INFORMATION
11.1 Information on toxicological effects:
The experimental information related to the toxicological properties of the product itself is not available
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than recommended by the occupational exposure
limits, it may result in adverse effects on health depending on the means of exposure:
A.- Ingestion (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met, however, it contains substances classified
as dangerous for consumption. For more information see section 3.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for this effect. For more information see section 3.
B- Inhalation (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met, as it does not contain substances classified
as dangerous for inhalation. For more information see section 3.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for this effect. For more information see section 3.
C- Contact with the skin and the eyes (acute effect):
- Contact with the skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for skin contact. For more information see section 3.
- Contact with the eyes: Based on available data, the classification criteria are not met, however it does contain substances
classified as dangerous for this effect. For more information see section 3.
D- CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
- Carcinogenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified
as dangerous for the effects mentioned. For more information see section 3.
- Mutagenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
- Reproductive toxicity: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for this effect. For more information see section 3.
E- Sensitizing effects:
- Respiratory: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous with sensitising effects. For more information see section 3.
- Cutaneous: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
F- Specific target organ toxicity (STOT) - single exposure:
Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
this effect. For more information see section 3.
G- Specific target organ toxicity (STOT)-repeated exposure:
- Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria are not met, as
it does not contain substances classified as dangerous for this effect. For more information see section 3.
- Skin: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
H- Aspiration hazard:
Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
this effect. For more information see section 3.
Other information:
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
12.1 Toxicity:
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 6/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 12: ECOLOGICAL INFORMATION (continued)
Identification Acute toxicity Species Genus
2-(2-[4-(1,1,3,3-Tetramethylbutyl)phenoxy]ethoxy)ethanol LC50 10 - 100 mg/L (96 h) Fish
CAS: 9036-19-5 EC50 10 - 100 mg/L Crustacean
EC: 618-541-1 EC50 10 - 100 mg/L Algae
12.2 Persistence and degradability:
Identification Degradability Biodegradability
2-(2-[4-(1,1,3,3-Tetramethylbutyl)phenoxy]ethoxy)ethanol BOD5 Non-applicable Concentration 100 mg/L
CAS: 9036-19-5 COD Non-applicable Period 28 days
EC: 618-541-1 BOD5/COD Non-applicable % Biodegradable 22 %
12.3 Bioaccumulative potential:
Not available
12.4 Mobility in soil:
Not available
12.5 Results of PBT and vPvB assessment:
Non-applicable
12.6 Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1 Waste treatment methods:
Waste class (Regulation (EU) No
Code Description
1357/2014)
08 01 12 Waste paint and varnish other than those mentioned in 08 01 11 Non dangerous
Type of waste (Regulation (EU) No 1357/2014):
Non-applicable
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations in accordance with Annex 1 and Annex
2 (Directive 2008/98/EC). As under 15 01 (2014/955/EC) of the code and in case the container has been in direct contact with
the product, it will be processed the same way as the actual product. Otherwise, it will be processed as non-dangerous residue.
We do not recommended disposal down the drain. See paragraph 6.2.
Regulations related to waste management:
In accordance with Annex II of Regulation (EC) nº1907/2006 (REACH) the community or state provisions related to waste
management are stated
Community legislation: Directive 2008/98/EC, 2014/955/EU, Regulation (EU) No 1357/2014
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport (ADR/RID,IMDG,IATA)
SECTION 15: REGULATORY INFORMATION
15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture:
Regulation (EC) No 528/2012: contains a preservative to protect the initial properties of the treated article. Contains 1,3-bis
(hydroxymethyl)-5,5-dimethylimidazolidine-2,4-dione.
Candidate substances for authorisation under the Regulation (EC) 1907/2006 (REACH): 2-(2-[4-(1,1,3,3-Tetramethylbutyl)
phenoxy]ethoxy)ethanol
Substances included in Annex XIV of REACH ("Authorisation List") and sunset date: Non-applicable
Regulation (EC) 1005/2009, about substances that deplete the ozone layer: Non-applicable
- CONTINUED ON NEXT PAGE -
Date of compilation: 31/05/2017 Version: 1 Page 7/8Safety data sheet
According to 1907/2006/EC (REACH), 2015/830/EU
ACRYLIC STUDIO
SECTION 15: REGULATORY INFORMATION (continued)
Regulation (EC) 1005/2009, about substances that deplete the ozone layer: Non-applicable
Article 95, REGULATION (EU) No 528/2012: Non-applicable
REGULATION (EU) No 649/2012, in relation to the import and export of hazardous chemical products: Non-applicable
Limitations to commercialisation and the use of certain dangerous substances and mixtures (Annex XVII REACH,
etc ….):
Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as data used in a risk evaluation of the local
circumstances in order to establish the necessary risk prevention measures for the manipulation, use, storage and disposal of this
product.
Other legislation:
The product could be affected by sectorial legislation
15.2 Chemical safety assessment:
The supplier has not carried out evaluation of chemical safety.
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with ANNEX II-Guide to the compilation of safety data sheets of
Regulation (EC) Nº 1907/2006 (Regulation (EC) Nº 2015/830)
Modifications related to the previous Safety Data Sheet which concerns the ways of managing risks.:
Non-applicable
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and refer to the
individual components which appear in section 3
CLP Regulation (EC) nº 1272/2008:
Acute Tox. 4: H302 - Harmful if swallowed
Aquatic Chronic 3: H412 - Harmful to aquatic life with long lasting effects
Eye Dam. 1: H318 - Causes serious eye damage
Classification procedure:
Non-applicable
Advice related to training:
Minimal training is recommended to prevent industrial risks for staff using this product, in order to facilitate their comprehension
and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
http://esis.jrc.ec.europa.eu
http://echa.europa.eu
http://eur-lex.europa.eu
Abbreviations and acronyms:
ADR: European agreement concerning the international carriage of dangerous goods by road
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5-day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
LC50: Lethal Concentration 50
EC50: Effective concentration 50
Log-POW: Octanol–water partition coefficient
Koc: Partition coefficient of organic carbon
The information contained in this safety data sheet is based on sources, technical knowledge and current legislation at European and state level, without being able to guarantee its accuracy. This
information cannot be considered a guarantee of the properties of the product, it is simply a description of the security requirements. The occupational methodology and conditions for users of
this product are not within our awareness or control, and it is ultimately the responsibility of the user to take the necessary measures to obtain the legal requirements concerning the
manipulation, storage, use and disposal of chemical products. The information on this safety data sheet only refers to this product, which should not be used for needs other than those specified.
- END OF SAFETY DATA SHEET -
Date of compilation: 31/05/2017 Version: 1 Page 8/8Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 1: IDENTIFICATION
1.1 GHS Product identifier: ACRYLIC STUDIO
1.2 Recommended use of the chemical and restrictions on use:
Relevant uses: Paint
Uses advised against: All uses not specified in this section or in section 7.3
1.3 Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party:
ACRYLICOS VALLEJO, S.L.
Pol. Ind. Sant Jordi - C/ Eusebio Millán, 14
08800 Vilanova i La Geltrú - Barcelona - Spain
Phone.: +34938936012 -
Fax: +34938931154
vallejo@acrylicosvallejo.com
www.acrylicosvallejo.com
1.4 Emergency phone number: +34 938 936 012 (9:00 - 17:00)
SECTION 2: HAZARD(S) IDENTIFICATION
2.1 Classification of the substance or mixture:
29 CFR 1910.1200:
While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this SDS
contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and
available for employees and other users of this product.
2.2 Label elements:
29 CFR 1910.1200:
None
2.3 Other hazards which do not result in classification:
Non-applicable
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1 Substances:
Non-applicable
3.2 Mixtures:
Chemical description: Mixture composed of additives, pigments and resins
Components:
None of the substances contained in the mixture are above the values fixed in Appendix D to § 1910.1200.
SECTION 4: FIRST-AID MEASURES
4.1 Description of necessary measures:
Consult a doctor in case of discomfort with this Safety data Sheet.
By inhalation:
In case of symptoms, move the person affected into fresh air.
By skin contact:
In case of contact it is recommended to clean the affected area thoroughly with water and neutral soap. In case of modifications
on the skin (stinging, redness, rashes, blisters,…), seek medical advice with this Safety data Sheet
By eye contact:
Rinse with water until the product has been eliminated. In case of problems, consult a doctor with the SDS of this product.
By ingestion/aspiration:
In case of consumption in large quantities, it is recommended to seek medical assistance.
4.2 Most important symptoms/effects, acute and delayed:
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 1/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 4: FIRST-AID MEASURES (continued)
Acute and delayed effects are indicated in sections 2 and 11.
4.3 Indication of immediate medical attention and special treatment needed, if necessary:
Non-applicable
SECTION 5: FIRE-FIGHTING MEASURES
5.1 Suitable (and unsuitable) extinguishing media:
Product is non-flammable, low risk of fire by the inflammability characteristics of the product in normal conditions of storage,
manipulation and use. In the case of the existence of sustained combustion as a result of improper manipulation, storage or use
any type of extinguishing agent can be used (ABC Powder, water,...)
5.2 Specific hazards arising from the chemical:
Due to its non-flammable nature, the product does not present a fire risk under normal conditions of storage, manipulation and
use.
5.3 Special protective equipment and precautions for fire-fighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and individual respiratory equipment.
Minimum emergency facilities and equipment should be available (fire blankets, portable first aid kit,...)
Additional provisions:
As in any fire, prevent human exposure to fire, smoke, fumes or products of combustion. Only properly trained personnel should
be involved in firefighting. Evacuate nonessential personnel from the fire area. Destroy any source of ignition. In case of fire,
refrigerate the storage containers and tanks for products susceptible to inflammation. Avoid spillage of the products used to
extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1 Personal precautions, protective equipment and emergency procedures:
Isolate leaks provided that there is no additional risk for the people performing this task.
6.2 Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and underground water.
6.3 Methods and materials for containment and cleaning up:
It is recommended:
Absorb the spillage using sand or inert absorbent and move it to a safe place. Do not absorb in sawdust or other combustible
absorbents. For any concern related to disposal consult section 13.
6.4 Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1 Precautions for safe handling:
A.- Precautions for safe manipulation
Comply with the current standards 29 CFR 1910 Occupational Safety and Health Standards. Keep containers hermetically
sealed. Control spills and residues, destroying them with safe methods (section 6). Avoid leakages from the container.
Maintain order and cleanliness where dangerous products are used.
B.- Technical recommendations for the prevention of fires and explosions
It is recommended to transfer at a slow speed to avoid the creation of electrostatic charges that could affect flammable
products. Consult section 10 for conditions and materials that should be avoided.
C.- Technical recommendations to prevent ergonomic and toxicological risks
Do not eat or drink during the process, washing hands afterwards with suitable cleaning products.
D.- Technical recommendations to prevent environmental risks
It is not necessary to take special measures to prevent environmental risks. For more information see subsection 6.2
7.2 Conditions for safe storage, including any incompatibilities:
A.- Technical measures for storage
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 2/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 7: HANDLING AND STORAGE (continued)
Minimum Temp.: 41 ºF
Maximum Temp.: 86 ºF
B.- General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see subsection 10.5
7.3 Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding the uses of this
product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 Control parameters:
Substances whose occupational exposure limits have to be monitored in the work environment
There are no occupational exposure limits for the substances contained in the product
8.2 Appropriate engineering controls:
A.- Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protection Equipment. For more information on Personal
Protection Equipment (storage, use, cleaning, maintenance, class of protection,…) consult the information leaflet provided by
the manufacturer. For more information see subsection 7.1. All information contained herein is a recommendation, the
information on clothing performance must be combined with professional judgment, and a clear understanding of the clothing
application, to provide the best protection to the worker. All chemical protective clothing use must be based on a hazard
assessment to determine the risks for exposure to chemicals and other hazards. Conduct hazard assessments in accordance
with 29 CFR 1910.132.
B.- Respiratory protection
The use of protection equipment will be necessary if a mist forms or if the occupational exposure limits are exceeded.
C.- Specific protection for the hands
Pictogram PPE Remarks
Replace gloves in case of any sign of damage. For prolonged periods of exposure
to the product for professional /industrial users, we recommend using chemical
Protective gloves against minor risks
protection gloves. Use gloves in accordance with manufacturer´s use limitations
Mandatory hand and OSHA standard 1910.138 (29CFR)
protection
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in advance with
total reliability and has therefore to be checked prior to the application
D.- Ocular and facial protection
Pictogram PPE Remarks
Clean daily and disinfect periodically according to the manufacturer´s instructions.
Panoramic glasses against splash/projections. Use if there is a risk of splashing. Use this PPE in accordance with manufacturer´s
use limitations and OSHA standard 1910.133 (29CFR)
Protección obligatoria
de la cara
E.- Bodily protection
Pictogram PPE Remarks
Work clothing Replace before any evidence of deterioration.
Anti-slip work shoes Replace before any evidence of deterioration.
F.- Additional emergency measures
It is not necessary to take additional emergency measures.
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 3/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid environmental
spillage of both the product and its container. For additional information see subsection 7.1.D
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1 Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 68 ºF: Liquid
Appearance: Dense
Color: Characteristic
Odor: Characteristic
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: 220 ºF
Vapour pressure at 68 ºF: 2335 Pa
Vapour pressure at 122 ºF: 12250 Pa (12 kPa)
Evaporation rate at 68 ºF: Non-applicable *
Product description:
Density at 68 ºF: 1089 kg/m³
Relative density at 68 ºF: 1.231
Dynamic viscosity at 68 ºF: 15000 - 20000 cP
Kinematic viscosity at 68 ºF: Non-applicable *
Kinematic viscosity at 104 ºF: Non-applicable *
Concentration: Non-applicable *
pH: 8-9
Vapour density at 68 ºF: Non-applicable *
Partition coefficient n-octanol/water 68 ºF: Non-applicable *
Solubility in water at 68 ºF: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Flammability:
Flash Point: Non Flammable (>199.4 ºF)
Flammability (solid, gas): Non-applicable *
Autoignition temperature: 714 ºF
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive:
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
9.2 Other information:
Surface tension at 68 ºF: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 4/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Surface tension at 68 ºF: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1 Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See section 7.
10.2 Chemical stability:
Chemically stable under the conditions of storage, handling and use.
10.3 Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not expected.
10.4 Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Not applicable Not applicable Not applicable
10.5 Incompatible materials:
Acids Water Combustive materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable Not applicable
10.6 Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the decomposition conditions,
complex mixtures of chemical substances can be released: carbon dioxide (CO2), carbon monoxide and other organic
compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1 Information on toxicological effects:
LD50 oral > 5000 mg/kg (rat)
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than recommended by the occupational exposure
limits, it may result in adverse effects on health depending on the means of exposure:
A.- Ingestion (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met
- Corrosivity/Irritability: Based on available data, the classification criteria are not met
B- Inhalation (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met
- Corrosivity/Irritability: Based on available data, the classification criteria are not met
C- Contact with the skin and the eyes (acute effect):
- Contact with the skin: Based on available data, the classification criteria are not met
- Contact with the eyes: Based on available data, the classification criteria are not met
D- CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
- Carcinogenicity: Based on available data, the classification criteria are not met
- Mutagenicity: Based on available data, the classification criteria are not met
- Reproductive toxicity: Based on available data, the classification criteria are not met
E- Sensitizing effects:
- Respiratory: Based on available data, the classification criteria are not met
- Cutaneous: Based on available data, the classification criteria are not met
F- Specific target organ toxicity (STOT) - single exposure:
Based on available data, the classification criteria are not met
G- Specific target organ toxicity (STOT)-repeated exposure:
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 5/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 11: TOXICOLOGICAL
G- Specific INFORMATION
target organ toxicity (STOT)-repeated(continued)
exposure:
- Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria are not met
- Skin: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
H- Aspiration hazard:
Based on available data, the classification criteria are not met
Other information:
Non-applicable
Specific toxicology information on the substances:
Not available
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
12.1 Ecotoxicity (aquatic and terrestrial, where available):
Not available
12.2 Persistence and degradability:
Not available
12.3 Bioaccumulative potential:
Not available
12.4 Mobility in soil:
Not available
12.5 Results of PBT and vPvB assessment:
Non-applicable
12.6 Other adverse effects:
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1 Disposal methods:
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations. In case the container has been in
direct contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed as non-
dangerous residue. We do not recommended disposal down the drain. See epigraph 6.2.
Regulations related to waste management:
Legislation related to waste management:
40 CFR Part 261- IDENTIFICATION AND LISTING OF HAZARDOUS WASTE
SECTION 14: TRANSPORT INFORMATION
This product is not regulated for transport.
SECTION 15: REGULATORY INFORMATION
15.1 Safety, health and environmental regulations specific for the product in question:
- CONTINUED ON NEXT PAGE -
Date of compilation: 5/31/2017 Version: 1 Page 6/7Safety data sheet
according to 29 CFR 1910.1200
ACRYLIC STUDIO
SECTION 15: REGULATORY INFORMATION (continued)
SARA Title III - Toxic Chemical Release Inventory Reporting (Section 313): Non-applicable
California Proposition 65 (the Safe Drinking Water and Toxic Enforcement Act of 1986): Non-applicable
The Toxic Substances Control Act (TSCA) : Non-applicable
Massachusetts RTK - Substance List: Non-applicable
New Jersey Worker and Community Right-to-Know Act: Non-applicable
New York RTK - Substance list: Non-applicable
Pennsylvania Worker and Community Right-to-Know Law: Non-applicable
NTP (National Toxicology Program): Non-applicable
Hazardous substances release notification under CERCLA sections 102-103 (40 CFR Part 302): Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as data used in a risk evaluation of the local
circumstances in order to establish the necessary risk prevention measures for the manipulation, use, storage and disposal of this
product.
Other legislation:
The Toxic Substances Control Act (TSCA)
SARA Title III - Community Right-to-Know Reporting Requirements (Sections 311-312)
SARA Title III - Toxic Chemical Release Inventory Reporting (Section 313)
Emergency Planning and Community Right-to-Know Act (EPCRA) Reportable Quantities
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with Appendix d to §1910.1200 – Safety data sheets
Texts of the legislative phrases mentioned in section 3:
The phrases indicated do not refer to the product itself; they are present merely for informative purposes and refer to the
individual components which appear in section 3
29 CFR 1910.1200:
Non-applicable
Advice related to training:
Minimal training is recommended to prevent industrial risks for staff using this product, in order to facilitate their comprehension
and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
Occupational Safety & Health Administration (OSHA).
Abbreviations and acronyms:
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5-day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
CL50: Lethal Concentration 50
EC50: Effective concentration 50
Log-POW: Octanol–water partition coefficient
Koc: Partition coefficient of organic carbon
The information contained in this safety data sheet is based on sources, technical knowledge and current USA legislation, without being able to guarantee its accuracy. This information cannot be
considered a guarantee of the properties of the product, it is simply a description of the security requirements. The occupational methodology and conditions for users of this product are not
within our awareness or control, and it is ultimately the responsibility of the user to take the necessary measures to obtain the legal requirements concerning the manipulation, storage, use and
disposal of chemical products. The information on this safety data sheet only refers to this product, which should not be used for needs other than those specified.
END OF SAFETY DATA SHEET
Date of compilation: 5/31/2017 Version: 1 Page 7/7Ficha de datos de seguridad
según 1907/2006/CE (REACH), 2015/830/EU
ACRYLIC STUDIO
SECCIÓN 1: IDENTIFICACIÓN DE LA SUSTANCIA O LA MEZCLA Y DE LA SOCIEDAD O EMPRESA
1.1 Identificador del producto: ACRYLIC STUDIO
1.2 Usos pertinentes identificados de la sustancia o de la mezcla y usos desaconsejados:
Usos pertinentes: Pintura
Usos desaconsejados: Todo aquel uso no especificado en este epígrafe ni en el epígrafe 7.3
1.3 Datos del proveedor de la ficha de datos de seguridad:
ACRYLICOS VALLEJO, S.L.
Pol. Ind. Sant Jordi - C/ Eusebio Millán, 14
08800 Vilanova i La Geltrú - Barcelona - Spain
Tfno.: +34938936012 -
Fax: +34938931154
vallejo@acrylicosvallejo.com
www.acrylicosvallejo.com
1.4 Teléfono de emergencia: +34 938 936 012 (9:00 - 17:00)
SECCIÓN 2: IDENTIFICACIÓN DE LOS PELIGROS
2.1 Clasificación de la sustancia o de la mezcla:
Reglamento nº1272/2008 (CLP):
De acuerdo al Reglamento nº1272/2008 (CLP), el producto no es clasificado como peligroso
2.2 Elementos de la etiqueta:
Reglamento nº1272/2008 (CLP):
Ninguno
2.3 Otros peligros:
No relevante
SECCIÓN 3: COMPOSICIÓN/INFORMACIÓN SOBRE LOS COMPONENTES
3.1 Sustancia:
No aplicable
3.2 Mezclas:
Descripción química: Mezcla a base de aditivos, pigmentos y resinas
Componentes:
De acuerdo al Anexo II del Reglamento (CE) nº1907/2006 (punto 3), el producto presenta:
Identificación Nombre químico/clasificación Concentración
CAS: 9036-19-5 2-(2-[4-(1,1,3,3-tetrametilbutil)fenoxi]etoxi)etanol Autoclasificada
CE: 618-541-1Ficha de datos de seguridad
según 1907/2006/CE (REACH), 2015/830/EU
ACRYLIC STUDIO
SECCIÓN 4: PRIMEROS AUXILIOS (continúa)
Se trata de un producto que no contiene sustancias clasificadas como peligrosas en contacto con la piel, sin embargo, en caso de
contacto se recomienda limpiar la zona afectada con agua por arrastre y con jabón neutro.
Por contacto con los ojos:
Enjuagar los ojos con abundante agua al menos durante 15 minutos. En el caso de que el accidentado use lentes de contacto,
éstas deben retirarse siempre que no estén pegadas a los ojos, de otro modo podría producirse un daño adicional. En todos los
casos, después del lavado, se debe acudir al médico lo más rápidamente posible con la FDS del producto.
Por ingestión/aspiración:
No inducir al vómito, en el caso de que se produzca mantener inclinada la cabeza hacia delante para evitar la aspiración.
Mantener al afectado en reposo. Enjuagar la boca y la garganta, ya que existe la posibilidad de que hayan sido afectadas en la
ingestión.
4.2 Principales síntomas y efectos, agudos y retardados:
Los efectos agudos y retardados son los indicados en las secciones 2 y 11.
4.3 Indicación de toda atención médica y de los tratamientos especiales que deban dispensarse inmediatamente:
No relevante
SECCIÓN 5: MEDIDAS DE LUCHAS CONTRA INCENDIOS
5.1 Medios de extinción:
Producto no inflamable bajo condiciones normales de almacenamiento, manipulación y uso. En caso de inflamación como
consecuencia de manipulación, almacenamiento o uso indebido emplear preferentemente extintores de polvo polivalente (polvo
ABC), de acuerdo al Reglamento de instalaciones de protección contra incendios (R.D. 1942/1993 y posteriores modificaciones).
NO SE RECOMIENDA emplear agua a chorro como agente de extinción.
5.2 Peligros específicos derivados de la sustancia o la mezcla:
Como consecuencia de la combustión o descomposición térmica se generan subproductos de reacción que pueden resultar
altamente tóxicos y, consecuentemente, pueden presentar un riesgo elevado para la salud.
5.3 Recomendaciones para el personal de lucha contra incendios:
En función de la magnitud del incendio puede hacerse necesario el uso de ropa protectora completa y equipo de respiración
autónomo. Disponer de un mínimo de instalaciones de emergencia o elementos de actuación (mantas ignífugas, botiquín
portátil,...) conforme al R.D.486/1997 y posteriores modificaciones
Disposiciones adicionales:
Actuar conforme el Plan de Emergencia Interior y las Fichas Informativas sobre actuación ante accidentes y otras emergencias.
Suprimir cualquier fuente de ignición. En caso de incendio, refrigerar los recipientes y tanques de almacenamiento de productos
susceptibles a inflamación, explosión o BLEVE como consecuencia de elevadas temperaturas. Evitar el vertido de los productos
empleados en la extinción del incendio al medio acuático.
SECCIÓN 6: MEDIDAS EN CASO DE VERTIDO ACCIDENTAL
6.1 Precauciones personales, equipo de protección y procedimientos de emergencia:
Aislar las fugas siempre y cuando no suponga un riesgo adicional para las personas que desempeñen esta función. Ante la
exposición potencial con el producto derramado se hace obligatorio el uso de elementos de protección personal (ver sección 8).
Evacuar la zona y mantener a las personas sin protección alejadas.
6.2 Precauciones relativas al medio ambiente:
Evitar el vertido al medio acuático debido a que contiene sustancias peligrosas para el mismo. Contener el producto
absorbido/recogido en recipientes precintables Notificar en caso de grandes vertidos al medio acuático a la autoridad competente.
6.3 Métodos y material de contención y de limpieza:
Se recomienda:
Absorber el vertido mediante arena o absorbente inerte y trasladarlo a un lugar seguro. No absorber en serrín u otros
absorbentes combustibles. Para cualquier consideración relativa a la eliminación consultar la sección 13.
6.4 Referencias a otras secciones:
Ver secciones 8 y 13.
SECCIÓN 7: MANIPULACIÓN Y ALMACENAMIENTO
7.1 Precauciones para una manipulación segura:
- CONTINÚA EN LA SIGUIENTE PÁGINA -
Emisión: 31/05/2017 Versión: 1 Página 2/9Ficha de datos de seguridad
según 1907/2006/CE (REACH), 2015/830/EU
ACRYLIC STUDIO
SECCIÓN 7: MANIPULACIÓN Y ALMACENAMIENTO (continúa)
A.- Precauciones generales
Cumplir con la legislación vigente en materia de prevención de riesgos laborales. Mantener los recipientes herméticamente
cerrados. Controlar los derrames y residuos, eliminándolos con métodos seguros (sección 6). Evitar el vertido libre desde el
recipiente. Mantener orden y limpieza donde se manipulen productos peligrosos.
B.- Recomendaciones técnicas para la prevención de incendios y explosiones.
Producto no inflamable bajo condiciones normales de almacenamiento, manipulación y uso. Se recomienda trasvasar a
velocidades lentas para evitar la generación de cargas electroestáticas que pudieran afectar a productos inflamables.
Consultar la sección 10 sobre condiciones y materias que deben evitarse.
C.- Recomendaciones técnicas para prevenir riesgos ergonómicos y toxicológicos.
Para control de exposición consultar la sección 8. No comer, beber ni fumar en las zonas de trabajo; lavarse las manos
después de cada utilización, y despojarse de prendas de vestir y equipos de protección contaminados antes de entrar en las
zonas para comer.
D.- Recomendaciones técnicas para prevenir riesgos medioambientales
Se recomienda disponer de material absorbente en las proximidades del producto (ver epígrafe 6.3)
7.2 Condiciones de almacenamiento seguro, incluidas posibles incompatibilidades:
A.- Medidas técnicas de almacenamiento
ITC (R.D.379/2001): No relevante
Clasificación: No relevante
Tª mínima: 5 ºC
Tª máxima: 30 ºC
B.- Condiciones generales de almacenamiento.
Evitar fuentes de calor, radiación, electricidad estática y el contacto con alimentos. Para información adicional ver epígrafe
10.5
7.3 Usos específicos finales:
Salvo las indicaciones ya especificadas no es preciso realizar ninguna recomendación especial en cuanto a los usos de este
producto.
SECCIÓN 8: CONTROLES DE EXPOSICIÓN/PROTECCIÓN INDIVIDUAL
8.1 Parámetros de control:
Sustancias cuyos valores límite de exposición profesional han de controlarse en el ambiente de trabajo (INSHT 2015):
No existen valores límites ambientales para las sustancias que constituyen el producto.
DNEL (Trabajadores):
No relevante
DNEL (Población):
No relevante
PNEC:
No relevante
8.2 Controles de la exposición:
A.- Medidas generales de seguridad e higiene en el ambiente de trabajo:
Como medida de prevención se recomienda la utilización de equipos de protección individual básicos, con el correspondiente
""marcado CE"" de acuerdo al R.D.1407/1992 y posteriores modificaciones. Para más información sobre los equipos de
protección individual (almacenamiento, uso, limpieza, mantenimiento, clase de protección,…) consultar el folleto informativo
facilitado por el fabricante del EPI. Las indicaciones contenidas en este punto se refieren al producto puro. Las medidas de
protección para el producto diluido podrán variar en función de su grado de dilución, uso, método de aplicación, etc. Para
determinar la obligación de instalación de duchas de emergencia y/o lavaojos en los almacenes se tendrá en cuenta la
normativa referente al almacenamiento de productos químicos aplicable en cada caso. Para más información ver epígrafes 7.1
y 7.2.
Toda la información aquí incluida es una recomendación siendo necesario su concreción por parte de los servicios de
prevención de riesgos laborales al desconocer las medidas de prevención adicionales que la empresa pudiese disponer.
B.- Protección respiratoria.
- CONTINÚA EN LA SIGUIENTE PÁGINA -
Emisión: 31/05/2017 Versión: 1 Página 3/9Ficha de datos de seguridad
según 1907/2006/CE (REACH), 2015/830/EU
ACRYLIC STUDIO
SECCIÓN 8: CONTROLES DE EXPOSICIÓN/PROTECCIÓN INDIVIDUAL (continúa)
Será necesario la utilización de equipos de protección en el caso de formación de nieblas o en el caso de superar los límites de
exposición profesional si existiesen (Ver Epígrafe 8.1).
C.- Protección específica de las manos.
Pictograma EPI Marcado Normas CEN Observaciones
Reemplazar los guantes ante cualquier indicio de
deterioro. Para periodos de exposición prolongados
Guantes de protección contra
al producto para usuarios profesionales/industriales
riesgos menores
se hace recomendable la utilización de guantes CE
Proteccion obligatoria III, de acuerdo a las normas EN 420 y EN 374
de la manos
Dado que el producto es una mezcla de diferentes materiales, la resistencia del material de los guantes no se puede calcular
de antemano con total fiabilidad y por lo tanto tiene que ser controlados antes de su aplicación.
D.- Protección ocular y facial
Pictograma EPI Marcado Normas CEN Observaciones
Limpiar a diario y desinfectar periodicamente de
Gafas panorámicas contra
EN 166:2001 acuerdo a las instrucciones del fabricante. Se
salpicaduras y/o
EN ISO 4007:2012 recomienda su uso en caso de riesgo de
proyecciones
Proteccion obligatoria salpicaduras.
de la cara
E.- Protección corporal
Pictograma EPI Marcado Normas CEN Observaciones
Reemplazar ante cualquier indicio de deterioro.
Para periodos de exposición prolongados al
producto para usuarios profesionales/industriales se
Ropa de trabajo
hace recomendable CE III, de acuerdo a las normas
EN ISO 6529:2001, EN ISO 6530:2005, EN ISO
13688:2013, EN 464:1994
Reemplazar ante cualquier indicio de deterioro.
Para periodos de exposición prolongados al
Calzado de trabajo
EN ISO 20347:2012 producto para usuarios profesionales/industriales se
antideslizamiento
hace recomendable CE III, de acuerdo a las normas
EN ISO 20345 y EN 13832-1
F.- Medidas complementarias de emergencia
Medida de emergencia Normas Medida de emergencia Normas
ANSI Z358-1 DIN 12 899
ISO 3864-1:2002 ISO 3864-1:2002
Ducha de emergencia Lavaojos
Controles de la exposición del medio ambiente:
En virtud de la legislación comunitaria de protección del medio ambiente se recomienda evitar el vertido tanto del producto como
de su envase al medio ambiente. Para información adicional ver epígrafe 7.1.D
Compuestos orgánicos volátiles:
En aplicación al R.D.117/2003 y posteriores modificaciones (Directiva 2010/75/EU), este producto presenta las siguientes
características:
C.O.V. (Suministro): 0,03 % peso
Concentración C.O.V. a 20 ºC: 0,3 kg/m³ (0,3 g/L)
Número de carbonos medio: 6,11
Peso molecular medio: 115,95 g/mol
SECCIÓN 9: PROPIEDADES FÍSICAS Y QUÍMICAS
9.1 Información de propiedades físicas y químicas básicas:
Para completar la información ver la ficha técnica/hoja de especificaciones del producto.
Aspecto físico:
Estado físico a 20 ºC: Líquido
*No relevante debido a la naturaleza del producto, no aportando información característica de su peligrosidad.
- CONTINÚA EN LA SIGUIENTE PÁGINA -
Emisión: 31/05/2017 Versión: 1 Página 4/9You can also read
