BLUEDOG WIRE STRIPPERS - www.copper-wire-stripper.com - BWS-80 Wire Stripping Machine
←
→
Page content transcription
If your browser does not render page correctly, please read the page content below
BWS-80 Wire Stripping Machine
Operation Manual
BLUEDOG WIRE STRIPPERS
www.copper-wire-stripper.comContents 1. Specification and composition…………………………………………………1-4 2. Operation………………………………………………………………………4-5 3. Common trouble shooting and maintenance……………………………………6 4. Security declaration……………………………………………………………6-7
1. Specification and composition
1.1 The use of the machine
This machine is widely used for the waste resource recycling industry. Its
function is to separate the cable’s insulation layer and its conductor to recycle
the copper, aluminum, plastic and rubber etc. in it for recycling.
1.2 Scope of application
1. Cable: dia. φ2mm～φ80mm
1.3 Technical parameter
1.3.1 supply voltage/Motor power/rate: AC380V/3KW/50HZ
(220V/3KW/50HZ)
1.3.2 Overall dimension: 1080mm※850mm※1200mm (L※W※H)
1.3.3 Weight: 405Kg
1.3.4 Processing capacity: 23m / min (left); 33m/min (right)
1.4 Working principle
1.4.1 Take the left cable stripper device as example. In Picture1 the cable stripper
device consists of the upper and lower idler wheels. Between the two wheels
there are blades. In front of the wheels is the inlet device. When the machine
starts, the upper and lower idler wheels operates relatively. The cable is
conveyed to the space between the two wheels through the feed port by
manual work. The cable is transported forward through the relative operation
of the two wheels. The upper and lower blades cut the insulating layer of the
cable open to make it separate from the conductor, thus achieving the
recycling purpose.
1.4.2 The working principle of the right cable stripper machine is the same with the
above statement.
Cable(Picture1)
1.5 Carrying, transporting and storing:
1.5.1 Carrying: The machine is equipped with castors. When the machine is carried
for a short distance, people can retract its sizing block and land on its castors
and then move it directly. When carried for a long distance or elevated, it
should be moved with forklift and other supporting removal tools.
1.5.2 Transporting: When transported, the machine should avoid being crushed and
impacted. Use certain measures to fix it to avoid damage.
1.5.3 Storing: The machine is better to be placed in dry and ventilated condition all
time.
1.6 Composition:
1.6.1 (picture 2)
Hand wheel
Switch Hand wheel ②
Material outlet board
Feed port ②
Shield
Hand wheel③
Motor
Feed port ①
Sizing block
Castors
(picture 2)1.6.2 Introduction of functions of each part:
1.6.2.1 Protection part: protect the workers from accidents while using machine.
1.6.2.2 Adjustment part: this part consists of left and right, up and down
adjustment devices. The cable’s cutting depth can be adjusted by rotating
the hand wheels , .
1.6.2.3 Feed port part: this part mainly consists of the left and right baffles,
pulleys etc. All cables with different diameters can be clamped by rotating
and adjusting the hand wheel .
1.6.2.4 Transmission part: this part mainly consists of electrical machine, transfer
axis, pulley component elements etc.
1.6.2.5 Feed port part: There are nine round feed ports in different sizes to direct
the cable into the machine for stripping. During wire stripping, feed ports
should be selected according to the diameters of cable lines to be stripped.
When there are several feed ports for selection, testing processing should be
conducted from large aperture to small ones in turn.
Pay attention that cables with piecing or plug should be removed first to
avoid influencing the stripping effect or damaging the machine.
1.6.2.6 Wire stripping part: this part mainly consists of the left and right cable
stripper devices. The right one is used for stripping finer cables, while the
left one is used for stripping heavier ones. If the thickness of the cable’s
insulating layer is over 6mm, the upper idler wheel should be replaced by
circular knives. The replacing method is introduced in detail in “2.1.5”.
1.6.2.7 Electronic control part:
Power supply of the machine: AC380/50HZ.（220V/50HZ）
Users should examine carefully whether all the ligatures and electrical
components are in good condition. Only when they are all normal can the
machine be started up. If emergency occurs, please switch off power
rapidly.
1.7 Notes of test run:
1.7.1 Inspection
1. Check whether the fastening piece is fixed or not.
2. Check whether the transmission part is loosened or not.
3. Check whether the electrical part is in good condition.2. Operation
2.1.1 Read this manual in detail before use the machine.
2.1.2 The power of this machine is AC380V; the power should be connected
right.
2.1.3 After the power is on, press the “Co-rotation” button to start the
Machine.
2.1.4. Choose appropriate feed port for wire stripping according to the cable
size (picture 3). Rotate the hand wheels to guarantee the best cutting depth.
While using the left cable stripper device, the cutting depth can have fine
adjustment by adjusting the components to which the arrows point in
(picture4. If the thickness of the cable’s insulating layer is over 6mm, the
upper idler wheel should be replaced by circular knife.
2.1.5 The replacing method for the left circular knives is as following:
First remove the upper long knife and gear (picture 6);
. Install and fix the circular knife (picture 7).
2.1.6 If emergency occurs during the stripping process, press the “Scram” button
to stop the machine.
2.1.7 Clearing the residues on the machine after use.
(picture 3)(picture4) (picture5) (picture6)
3. Common trouble shooting
Common faults Solutions
1. Check whether the power is connected.
The stripper machine doesn’t 2. Check whether the electric wire is in good
work after being started. condition.
3. Check whether the motor is damaged.
1. Reselect the feed port.
The cable is out of rabbet.
2. Adjust hand wheel or .
1. Reselect the feed port.
The insulating layer of the 2. Adjust hand wheel or .
cable can’t be stripped. 3. Check whether the blades are in good condition.
4. Replace new blades.
1. Check whether the belt is in good condition.
The motor belt falls off. 2. Reset the motor.
3. Replace the belt.
1. Check whether some components are loosened.
There is abnormal sound after 2. Check whether the bearing is in good condition.
the machine is started. 3. Check whether the chain is in good condition.
4. Add lubricating oil.
Maintaining:
2.1 Clean up the machine after use.
2.2 Add lubricating oil for bearing.
2.3 Add antirust oil for gear and blade.
2.4 Place it in dry condition.
4. Security declaration
4.1 Unsafe factors:
1. The machine is equipped with sharp blades. When material blockage or
unsmooth ejection occurs during the operation, it will injure people who put
hands into the machine for taking out materials when the machine is in
operation (namely when the blade is running).
2. The used power of this machine is 380V; it is demanded that the operator
should operate according to the requirements to avoid being shocked by
electricity.
3. Take down the shield artificially and repair the machine while it is running.
4.2 Safety rules:
1. The machine can’t be started arbitrarily by person who is not familiar with
its performance and operation rules. It’s suggested that the operator should
read and learn this manual carefully.
2. Prohibit dismantling the protective parts that are related with the machine
safety. Before each use, check carefully the tightness of each part. Checkwhether electric parts are connected well and whether the switch can carry out the relevant action. 3. Prohibit arbitrary maintenance when the machine is running. If the emergency happens, the “OFF” switch should be pressed and the operation should be done after the power is cut off. 4. If the machine is blocked, shut down the machine, wear the protective gloves and pick up the materials using the relevant assistant tools. 5. During operation, please note the warning mark to avoid accidents.
You can also read
